2007 NISSAN 350Z brake rotor

BR-2Revision: 2006 November2007 350Z REMOVAL ........................................................... 29
INSTALLATION .................................................... 29
Removal and Installation of Brake Pad (With
Brembo Calipers) .................................................... 30
REMOVAL ........................................................... 30
HOW TO APPLY GREASE TO THE BRAKE PAD ... 30
INSTALLATION .................................................... 30
Removal and Installation of Brake Caliper Assembly
(Other than Brembo Calipers) ................................ 31
REMOVAL ........................................................... 31
INSTALLATION .................................................... 31
Removal and Installation of Brake Caliper Assembly
(With Brembo Calipers) .......................................... 32
REMOVAL ........................................................... 32
INSTALLATION .................................................... 32
Disassembly and Assembly of Brake Caliper
Assembly (Other than Brembo Calipers) ................ 33
DISASSEMBLY ................................................... 33
INSPECTION AFTER DISASSEMBLY ................ 34
ASSEMBLY ......................................................... 34
DISC ROTOR INSPECTION ............................... 35
Disassembly and Assembly of Brake Caliper
Assembly (With Brembo Calipers) .......................... 36
DISASSEMBLY ................................................... 36
CALIPER INSPECTION ...................................... 36
ASSEMBLY ......................................................... 36
DISC ROTOR INSPECTION ............................... 37
Brake Burnishing Procedure ................................... 38
REAR DISC BRAKE ................................................. 39
On-Vehicle Inspection ............................................. 39
PAD WEAR INSPECTION ................................... 39
Components ........................................................... 40
OTHER THAN BREMBO CALIPERS .................. 40
WITH BREMBO CALIPERS ................................ 41
Removal and Installation of Brake Pad (Other than Brembo Calipers) .................................................... 42
REMOVAL ............................................................ 42
INSTALLATION .................................................... 42
Removal and Installation of Brake Pad (With
Brembo Calipers) .................................................... 42
REMOVAL ............................................................ 42
HOW TO APPLY GREASE TO THE BRAKE PAD ... 43
INSTALLATION .................................................... 43
Removal and Installation of Brake Caliper Assembly
(Other than Brembo Calipers) ................................. 44
REMOVAL ............................................................ 44
INSTALLATION .................................................... 44
Removal and Installation of Brake Caliper Assembly
(With Brembo Calipers) ........................................... 45
REMOVAL ............................................................ 45
INSTALLATION .................................................... 45
Disassembly and Assembly of Brake Caliper
Assembly (Other than Brembo Calipers) ................ 45
DISASSEMBLY .................................................... 45
CALIPER INSPECTION ....................................... 46
ASSEMBLY .......................................................... 47
DISC ROTOR INSPECTION ............................... 48
Disassembly and Assembly of Brake Caliper
Assembly (With Brembo Calipers) .......................... 49
DISASSEMBLY .................................................... 49
CALIPER INSPECTION ....................................... 49
ASSEMBLY .......................................................... 49
DISC ROTOR INSPECTION ............................... 50
SERVICE DATA AND SPECIFICATIONS (SDS) ...... 52
General Specifications ............................................ 52
Brake Pedal ............................................................ 52
Brake Booster ......................................................... 52
Check Valve ............................................................ 52
Front Disc Brake ..................................................... 52
Rear Disc Brake ...................................................... 53

BR-4
PRECAUTIONS
Revision: 2006 November2007 350Z

Use flare nut crowfoot and torque wrench when removing and
installing brake tube.

When installing brake piping, be sure to check torque.

Before working, turn the ignition switch OFF and disconnect the
connectors of ABS actuator and control unit or the battery nega-
tive terminal.

Burnish the brake contact surfaces after refinishing or replacing
drums or rotors, after replacing pads or linings, or if a soft pedal
occurs at very low mileage.
Refer to BR-38, "
Brake Burnishing Procedure" .
WARNING:
Clean brake pads and shoes with a waste cloth, then wipe with a dust collector.SBR686C

BR-6
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
Revision: 2006 November2007 350Z
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTINGPFP:00003
NVH Troubleshooting ChartNFS00005
Use the chart below to help you find the cause of the symptom. If necessary, repair or replace these parts.
×: ApplicableReference page
BR-29
, BR-31
, BR-42
, BR-45
BR-26
, BR-39
BR-27
, BR-40—
—
BR-35
, BR-37
, BR-48
, BR-50
—
—
—
BR-35
, BR-37
, BR-48
, BR-50
—
NVH in PR section
NHV in RFD section
NVH in FAX, RAX and FSU, RSU section
NVH in WT section
NVH in WT section
NVH in RAX section
NVH in PS section
Possible cause and
SUSPECTED PARTS
Pads - damaged
Pads - uneven wear
Shims damaged
Rotor imbalance
Rotor damage
Rotor runout
Rotor deformation
Rotor deflection
Rotor rust
Rotor thickness variation
Drum out of round
PROPELLER SHAFT
DIFFERENTIAL
AXLE AND SUSPENSION
TIRES
ROAD WHEEL
DRIVE SHAFT
STEERING
Symptom BRAKENoise××× ×× ×××
××
Shake× × ×××
××
Shimmy, Judder×××××××× ××× ×

FRONT DISC BRAKE
BR-27
C
D
E
G
H
I
J
K
L
MA
B
BR
Revision: 2006 November2007 350Z
ComponentsNFS000AT
OTHER THAN BREMBO CALIPERS
WARNING:
Clean dust on caliper and brake pad with a vacuum dust collector to minimize the hazard of airborne
particles or other materials.
CAUTION:

While removing cylinder body, do not depress brake pedal because piston will pop out.

It is not necessary to remove torque member mounting bolts on torque member and brake hose
except for disassembly or replacement of caliper assembly. In this case, hang cylinder body with a
wire so that brake hose is not under tension.

Do not damage piston boot.

If any shim is subject to serious corrosion, replace it with a new one.

Always replace shim and shim covers as a set when replacing brake pads.

Keep disc rotor clean of brake fluid.

Burnish the brake pads and disc rotor mutually contacting surfaces after refinishing or replacing
rotors, after replacing pads, or if a soft pedal occurs at very low mileage. Refer to BR-38, "
Brake
Burnishing Procedure" .
1. Union bolt 2. Copper washer 3. Brake hose
4. Cap 5. Bleed valve 6. Sliding pin bolt
7. Piston seal 8. Piston 9. Piston boot
10. Cylinder body 11. Sliding pin 12. Torque member mounting bolt
13. Washer 14. Sliding pin boot 15. Bushing
16. Torque member 17. inner shim cover 18. inner shim
19. Inner pad 20. Pad retainer 21. Pad wear sensor
22. Outer pad 23. Outer shim 24. Outer shim cover
Refer to GI-11, "
Components" and the followings for the symbols in the figure.
1: Apply rubber grease.
2: Apply PBC (Poly Butyl Cuprysil) grease or silicone-based grease.
3: Apply polyglycol ether based lubricant.
: Apply brake fluid.
PFIA0746J

BR-28
FRONT DISC BRAKE
Revision: 2006 November2007 350Z
WITH BREMBO CALIPERS
NOTE:
Refer to BR-30, "
HOW TO APPLY GREASE TO THE BRAKE PAD" for how to apply grease to brake pads.
WARNING:
Clean dust on caliper and brake pad with a vacuum dust collector to minimize the hazard of airborne
particles or other materials.
CAUTION:

While the brake pad and cylinder body are separated, the piston may suddenly jump out, so do not
depress the brake pedal.

Apart from caliper assembly, disassembly or replacement, there is no need to remove caliper bolts
or brake hose or tube.

Do not damage piston boot.

Keep disc rotor clean of brake fluid.
1. Piston 2. Piston seal 3. Piston boot
4. Cap 5. Bleed valve 6. Washer
7. Bolt 8. Clips 9. Pad pins
10. Caliper 11. Inner pad 12. Cross spring
13. Outer pad 14. Pad wear sensor
Refer to GI-11, "
Components" and the followings for the symbols in the figure.
1: Apply rubber grease.
2: Apply polyglycol ether based lubricant.
: Apply brake fluid.
PFIA0674J

FRONT DISC BRAKE
BR-29
C
D
E
G
H
I
J
K
L
MA
B
BR
Revision: 2006 November2007 350Z

Burnish the brake pads and disc rotor mutually contacting surfaces after refinishing or replacing
rotors, after replacing pads, or if a soft pedal occurs at very low mileage. Refer to BR-38, "
Brake
Burnishing Procedure" .
Removal and Installation of Brake Pad (Other than Brembo Calipers)NFS000AU
REMOVAL
1. Remove tires from vehicle with a power tool.
2. Remove lower sliding pin bolt.
3. Hang cylinder body with a wire, and remove pads, shims and
pad retainers from torque member.
CAUTION:

When removing pad retainer from torque member, lift pad
retainer in the direction shown by arrow (shown in the
figure) so as not to deform it.

Do not damage piston boot.

Keep disc rotor clean of brake fluid.
INSTALLATION
1. Apply PBC (Poly Butyl Cuprysil) grease or silicone-based
grease between pad retainer and pad.
2. Install pad retainers and pad assemblies to torque member.
CAUTION:
Inner pad and outer pad have pad-return mechanism on
upper side of pad retainer. When installing pad to torque
member, be sure to install pad return lever to pad wear sen-
sor securely.
3. Install cylinder body to torque member.
CAUTION:
When replacing pads with new ones, press in piston until
pads can be installed. In this case, carefully monitor brake fluid level in reservoir tank because
brake fluid will return to master cylinder reservoir tank.
4. Install lower sliding pin bolt, and tighten it to the specified torque. Refer to BR-27, "
Components" .
5. Secure disc rotor with wheel nuts. Depress brake pedal a few times until it gets a responsive touch.
6. Check front disc brake for drag.
7. Install tires to vehicle.
SBR433D
SBR556E
SBR557E

FRONT DISC BRAKE
BR-31
C
D
E
G
H
I
J
K
L
MA
B
BR
Revision: 2006 November2007 350Z
2. Attach pad.
CAUTION:

Attach the pad with wear sensor to the outer side.

The side of the shim with the larger cutouts should be on
the entry side of the disc rotor spin.
3. Insert the upper pad pin from the inner cylinder side, then insert
firmly to the outer cylinder side through the hole in the top of the
pad.
4. As shown in the figure, place the top of the cross spring over the
top pad pin, press in the cross spring, push the lower pad pin
from the inner cylinder side to the outer cylinder side, and
secure the cross spring.
5. Insert the clip in the small hole at the end of the pad pin.
CAUTION:
If the clip is not fully attached, the pad pin or the pad could
fall out while the vehicle is in motion.
6. Install tires to vehicle.
Removal and Installation of Brake Caliper Assembly (Other than Brembo Cali-
pers)
NFS000AV
REMOVAL
1. Remove tires from vehicle with a power tool.
2. Fasten disc rotor using wheel nut.
3. Drain brake fluid gradually (from bleed valve while depressing brake pedal). Refer to BR-10, "
Drain and
Refill" .
4. Remove union bolt, and then remove brake hose from caliper
assembly.
5. Remove torque member mounting bolts (from torque member),
and remove caliper assembly (from vehicle with a power tool).
CAUTION:
Do not drop brake pad.
6. Remove disc rotor.
CAUTION:
Put matching marks on wheel hub assembly and disc rotor,
if it is necessary to remove disc rotor.
INSTALLATION
CAUTION:

Refill with new brake fluid “DOT 3”.

Do not reuse drained brake fluid.
1. Install disc rotor.
CAUTION:
Put alignment marks on disc rotor and wheel hub at the time of removal when reusing disc rotor.
2. Install caliper assembly to vehicle, and tighten torque member mounting bolts to the specified torque.
Refer to BR-27, "
Components" .
CAUTION:
Before installing torque member to vehicle, wipe oil and grease on washer seats on steering
knuckle and mounting surface of torque member.
PFIA0275E
PFIA0276E
SFIA0140E

BR-32
FRONT DISC BRAKE
Revision: 2006 November2007 350Z
3. Install a projection of brake hose metal fitting by aligning with protrusions on cylinder body, and tighten
union bolt to the specified torque. Refer to BR-27, "
Components" .
CAUTION:

Do not reuse copper washers for union bolts.

Assemble brake hose securely on caliper assembly.
4. After installing caliper assembly, refill with new brake fluid and bleed air. Refer to BR-11, "
Bleeding Brake
System" .
5. Install tires to vehicle.
Removal and Installation of Brake Caliper Assembly (With Brembo Calipers)NFS0000X
REMOVAL
1. Remove tires from vehicle with a power tool.
2. Drain brake fluid. Refer to BR-10, "
Drain and Refill" .
3. Remove the brake pad. Refer to BR-30, "
Removal and Installation of Brake Pad (With Brembo Calipers)" .
4. Remove the brake tube flare nut using a flare wrench.
5. Remove the brake tube bracket from the knuckle spindle.
6. Remove the caliper bolt and remove the caliper assembly from the vehicle.
7. Remove disc rotor.
CAUTION:
Put matching marks of wheel hub assembly and disc rotor, if it is necessary to remove when
removing disc rotor.
INSTALLATION
CAUTION:

Refill with new brake fluid “DOT 3”.

Never reuse drained brake fluid.
1. Install disc rotor.
CAUTION:
Put alignment marks on disc rotor and wheel hub at the time of removal when reusing disc rotor.
2. Install caliper assembly to the vehicle, and tighten bolts to the specified torque.
CAUTION:
When attaching the caliper assembly to the vehicle, wipe
any oil off the knuckle spindle washers and caliper assem-
bly attachment surfaces.
3. Attach the brake tube to the caliper assembly and partially tighten the flare nut.
PFIA0226E
PFIA0226E