2007 NISSAN 350Z service

REAR DISC BRAKE
BR-43
C
D
E
G
H
I
J
K
L
MA
B
BR
Revision: 2006 November2007 350Z
4. Using pliers, remove the pad from the caliper.
HOW TO APPLY GREASE TO THE BRAKE PAD
Pad Side
Apply PBC (Poly Butyl Cuprysil) grease or silicone-based grease
about 0.5 g (0.018 oz) per surface equally to back plate side of Inner
Pad and Outer Pad. (Refer to the figure)
CAUTION:
Make sure no foreign matter attaches itself to the grease.
Pad Rear
Apply approximately 1.5 g (0.053 oz) of PBC (Poly Butyl Cuprysil)
grease or silicone -based grease between shim cover (1) and pad
(2).

A: Outer side

B: Inner side
CAUTION:
Make sure no foreign matter attaches itself to the grease.
INSTALLATION
1. Insert the piston to the position where the pad is attached.
NOTE:
Using a disc brake piston tool (commercial service tool), etc., makes it easier to push in the piston.
CAUTION:
Pushing the piston in will make the brake fluid return to the master cylinder reservoir tank, so
watch the level of the surface of the reservoir tank.
2. Attach pad and shim cover.
BRD0348D
PFIA0235E
PFIA0704E

BR-52
SERVICE DATA AND SPECIFICATIONS (SDS)
Revision: 2006 November2007 350Z
SERVICE DATA AND SPECIFICATIONS (SDS)PFP:00030
General SpecificationsNFS00019
Unit: mm (in)
Brake PedalNFS0001A
Brake BoosterNFS0001B
Check ValveNFS0001C
Front Disc BrakeNFS0001D
Brake model Other than brembo With brembo
Front brakeRotor outer diameter × thickness 320 × 28.0 (12.60 × 1.102) 324 × 30.0 (12.76 × 1.181)
Pad length × width × thickness130.0 × 50.0 × 11.0
(5.12 × 1.97 × 0.43)11 7 . 1 × 53.3 × 9.3
(4.61 × 2.098 × 0.366)
Cylinder bore diameter 45.0 × 2 (1.772 × 2) 38 (1.50) × 2 + 44 (1.73) × 2
Rear brake Rotor outer diameter × thickness 308 × 16 (12.13 × 0.63) 322 × 22 (12.68 × 0.87)
Pad length × width × thickness83.0 × 31.9 × 8.5
(3.27 × 1.26 × 0.335)76.6 × 45 × 9.1
(3.016 × 1.77 × 0.358)
Cylinder bore diameter 42.86 (1.6874) 40.0 × 2 (1.575)
Master cylinder Cylinder bore diameter 26.99 (1.0626)
Control valve Valve type Electric brake force distribution
Brake booster Diaphragm diameterCoupe 255 (10.04)Pri: 230 (9.06)
Sec: 205 (8.07)
RoadsterPri: 230 (9.06)
Sec: 205 (8.07)Pri: 230 (9.06)
Sec: 205 (8.07)
Recommended brake fluid DOT 3
Brake pedal height (from dash lower panel top surface)M/T models 153.2 – 163.2 mm (6.03 – 6.43 in)
A/T models 161.5 – 171.5 mm (6.36 – 6.75 in)
Depressed pedal height [under a force of 490 N (50 kg, 110 lb)
with the engine running]M/T models More than 90 mm (3.54 in)
A/T models More than 95 mm (3.74 in)
Clearance between threaded end of the stop lamp switch/ASCD cancel switch and
stopper rubber0.74 – 1.96 mm (0.0291 – 0.0772 in)
Pedal play3 – 11 mm (0.12 – 0.43 in)
Vacuum leakage
[at vacuum of −66.7 kPa (−500 mmHg, −19.69 inHg)]Within 3.3 kPa (25 mmHg, 0.98 inHg) of vacuum for 15 seconds
Output rod lengthWith TCS 10.4 mm (0.409 in)
With VDC−6.2 mm (−0.244 in)
Input rod length125 mm (4.92 in)
Vacuum leakage
[at vacuum of −66.7 kPa(−500 mmHg, −19.69 inHg)]Within 1.3 kPa (10 mmHg, 0.39 inHg) of vacuum for 15 seconds
Brake model Other than brembo With brembo
Brake padStandard thickness (new) 11.0 mm (0.433 in) 9.3 mm (0.366 in)
Repair limit thickness 2.0 mm (0.079 in) 2.0 mm (0.079 in)
Disc rotorStandard thickness (new) 28.0 mm (1.102 in) 30.0mm (1.181 in)
Repair limit thickness 26.0 mm (1.024 in) 28.4mm (1.118 in)
Maximum uneven wear (measured at 8 positions) 0.015mm (0.0006 in) or less 0.015 mm (0.0006 in) or less
Runout limit (with it attached to the vehicle) 0.035 mm (0.0014 in) or less 0.040 mm (0.0016 in) or less
Runout limit (just the disc rotor) 0.020 mm (0.0008 in) or less 0.040 mm (0.0016 in) or less

SERVICE DATA AND SPECIFICATIONS (SDS)
BR-53
C
D
E
G
H
I
J
K
L
MA
B
BR
Revision: 2006 November2007 350Z
Rear Disc BrakeNFS0001E
Brake model Other than brembo With brembo
Brake padStandard thickness (new) 8.5 mm (0.335 in) 9.1 mm (0.358 in)
Repair limit thickness 2.0 mm (0.079 in) 2.0 mm (0.079 in)
Disc rotorStandard thickness (new) 16.0 mm (0.630 in) 22.0 mm (0.866 in)
Repair limit thickness 14.0 mm (0.551 in) 20.2 mm (0.795 in)
Maximum uneven wear (measured at 8 positions) 0.015 mm (0.0006 in) or less 0.015 mm (0.0006 in) or less
Runout limit (with it attached to the vehicle) 0.055 mm (0.0022 in) or less 0.070 mm (0.0028 in) or less
Runout limit (just the disc rotor) 0.020 mm (0.008 in) or less 0.040 mm (0.0016 in) or less

BR-54
SERVICE DATA AND SPECIFICATIONS (SDS)
Revision: 2006 November2007 350Z