2007 NISSAN 350Z brake fluid

TROUBLE DIAGNOSIS
AT-79
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: 2006 November2007 350Z58
OthersVehicle does not
decelerate by engine
brake.
Refer to AT-202,
"Vehicle Does Not
Decelerate by Engine
Brake" .ON vehicle1. PNP switchAT-102
2. A/T fluid level and stateAT- 4 9
3. A/T positionAT-206
4. Manual mode switchAT-157
5. CAN communication lineAT- 9 4
6. Control valve with TCMAT-215
OFF vehicle7. Input clutchAT-2768. High and low reverse clutchAT-286
9. Direct clutchAT-288
59Engine brake does
not work M5 → M4 .ON vehicle1. PNP switchAT-102
2. A/T fluid level and stateAT- 4 9
3. A/T positionAT-206
4. Manual mode switchAT-157
5. CAN communication lineAT- 9 4
6. Control valve with TCMAT-215
OFF vehicle 7. Front brake (brake band)AT-255
60Engine brake does
not work M4 → M3 .ON vehicle1. PNP switchAT-102
2. A/T fluid level and stateAT- 4 9
3. A/T positionAT-206
4. Manual mode switchAT-157
5. CAN communication lineAT- 9 4
6. Control valve with TCMAT-215
OFF vehicle7. Front brake (brake band)AT-2558. Input clutchAT-276
61Engine brake does
not work M3 → M2 .ON vehicle1. PNP switchAT-102
2. A/T fluid level and stateAT- 4 9
3. A/T positionAT-206
4. Manual mode switchAT-157
5. CAN communication lineAT- 9 4
6. Control valve with TCMAT-215
OFF vehicle7. Front brake (brake band)AT-2558. Input clutchAT-276
9. High and low reverse clutchAT-286
No. Items Symptom Condition Diagnostic ItemReference
page

AT-80
TROUBLE DIAGNOSIS
Revision: 2006 November2007 350Z
62
OthersEngine brake does
not work M2 → M1 .ON vehicle1. PNP switchAT- 1 0 2
2. A/T fluid level and stateAT- 4 9
3. A/T positionAT- 2 0 6
4. Manual mode switchAT- 1 5 7
5. CAN communication lineAT- 9 4
6. Control valve with TCMAT- 2 1 5
OFF vehicle7. Input clutchAT- 2 7 68. High and low reverse clutchAT- 2 8 6
9. Direct clutchAT- 2 8 8
63 Maximum speed low.ON vehicle1. A/T fluid level and stateAT- 4 9
2. Line pressure testAT- 5 0
3. Accelerator pedal position sensorAT- 1 3 1
4. CAN communication lineAT- 9 4
5. Direct clutch solenoid valveAT- 1 4 9
6. Control valve with TCMAT- 2 1 5
OFF vehicle7. Torque converterAT- 2 5 5
8. Oil pump assemblyAT- 2 7 1
9. Input clutchAT- 2 7 6
10. Gear systemAT- 2 4 6
11. High and low reverse clutchAT- 2 8 6
12. Direct clutchAT- 2 8 8
13. Forward one-way clutch (Parts behind drum support is
impossible to perform inspection by disassembly. Refer to
AT-17, "
Cross-sectional View" .)AT- 2 5 5
14 Forward brake (Parts behind drum support is impossible
to perform inspection by disassembly. Refer to AT-17,
"Cross-sectional View" .)AT- 2 5 5
64Extremely large
creep.ON vehicle1. Engine idle speed EC-76

2. CAN communication lineAT- 9 4
OFF vehicle 3. Torque converterAT- 2 5 5
65With selector lever in
“P” position, vehicle
does not enter parking
condition or, with
selector lever in
another position, park-
ing condition is not
cancelled.ON vehicle1. PNP switchAT- 1 0 2
2. A/T positionAT- 2 0 6
3. Parking pawl componentsAT- 2 4 6
66Vehicle runs with A/T
in “P” position.ON vehicle1. PNP switchAT- 1 0 2
2. A/T fluid level and stateAT- 4 9
3. A/T positionAT- 2 0 6
4. Control valve with TCMAT- 2 1 5
5. Parking pawl componentsAT- 2 4 6
OFF vehicle 6. Gear systemAT- 2 4 6
No. Items Symptom Condition Diagnostic ItemReference
page

TROUBLE DIAGNOSIS
AT-81
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: 2006 November2007 350Z
67
OthersVehicle runs with A/T
in “N” position.
Refer to AT-174, "In
“N” Position, Vehicle
Moves" .ON vehicle1. PNP switchAT-102
2. A/T fluid level and stateAT- 4 9
3. A/T positionAT-206
4. Control valve with TCMAT-215
OFF vehicle5. Input clutchAT-276
6. Gear systemAT-246
7. Direct clutchAT-288
8. Reverse brakeAT-255
9. Forward one-way clutch (Parts behind drum support is
impossible to perform inspection by disassembly. Refer to
AT- 1 7 , "
Cross-sectional View" .)AT-255
10. Low coast brake (Parts behind drum support is impossi-
ble to perform inspection by disassembly. Refer to AT-17,
"Cross-sectional View" .)AT-255
68Engine does not start
in “N” or “P” position.
Refer to AT-173, "Engine Cannot Be
Started in “P” or “N”
Position" .ON vehicle1. Ignition switch and starterPG-4
,
SC-8
2. A/T positionAT-206
3. PNP switchAT-102
69Engine starts in posi-
tions other than “N” or
“P”.ON vehicle1. Ignition switch and starterPG-4
,
SC-8
2. A/T positionAT-206
3. PNP switchAT-102
70 Engine stall.ON vehicle1. A/T fluid level and stateAT- 4 9
2. Engine speed signalAT- 11 3
3. Turbine revolution sensorAT-106
4. Torque converter clutch solenoid valveAT-125
5. CAN communication lineAT- 9 4
6. Control valve with TCMAT-215
OFF vehicle 7. Torque converterAT-255
71Engine stalls when
selector lever shifted
“N” → “D”, “R”.ON vehicle1. A/T fluid level and stateAT- 4 9
2. Engine speed signalAT- 11 3
3. Turbine revolution sensorAT-106
4. Torque converter clutch solenoid valveAT-125
5. CAN communication lineAT- 9 4
6. Control valve with TCMAT-215
OFF vehicle 7. Torque converterAT-255
No. Items Symptom Condition Diagnostic ItemReference
page

AT-82
TROUBLE DIAGNOSIS
Revision: 2006 November2007 350Z
72 OthersEngine speed does
not return to idle.
Refer to AT-195,
"Engine Speed Does
Not Return to Idle" .ON vehicle1. A/T fluid level and stateAT- 4 9
2. Direct clutch solenoid valveAT- 1 4 9
3. Front brake solenoid valveAT- 1 4 7
4. Accelerator pedal position sensorAT- 1 3 1
5. Vehicle speed sensor A/T and vehicle speed sensor MTRAT- 1 0 8,
AT- 1 3 9
6. CAN communication lineAT- 9 4
7. Control valve with TCMAT- 2 1 5
OFF vehicle8. Front brake (brake band)AT- 2 5 59. Direct clutchAT- 2 8 8
No. Items Symptom Condition Diagnostic ItemReference
page

TROUBLE DIAGNOSIS
AT-93
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: 2006 November2007 350Z
Judgment Self-diagnosis Code
If there is a malfunction, the lamp lights up for the time corresponding to the suspect circuit.
Erase Self-diagnosis

In order to make it easier to find the cause of hard-to-duplicate malfunctions, malfunction information is
stored into the control unit as necessary during use by the user. This memory is not erased no matter how
many times the ignition switch is turned ON and OFF.

However, this information is erased by turning ignition switch OFF after performing self-diagnostics or by
erasing the memory using the CONSULT-III.
No. Malfunctioning item No. Malfunctioning item
1 Revolution sensor AT-108
12 A/T interlock AT- 1 4 1
2 Direct clutch solenoid valve AT-14913 A/T 1st engine braking AT- 1 4 3
3 Torque converter clutch solenoid valve AT- 1 2 514 Start signal AT- 9 7
4 Line pressure solenoid valve AT- 1 2 915 Accelerator pedal position sensor AT- 1 3 1
5 Input clutch solenoid valve AT- 1 4 516 Engine speed signal AT- 11 3
6 Front brake solenoid valve AT- 1 4 717 CAN communication line AT- 9 4
7 Low coast brake solenoid valve AT- 1 5 3 , AT-15518 1st gear function AT- 11 5
8 High and low reverse clutch solenoid valve AT- 1 5 119 2nd gear function AT- 11 7
9 PNP switch AT-10220 3rd gear function AT- 11 9
10 A/T fluid temperature sensor AT- 1 3 421 4th gear function AT-121
11 Turbine revolution sensor AT- 1 0 622 5th gear function AT-123
SCIA8153E

AT-142
DTC P1730 A/T INTERLOCK
Revision: 2006 November2007 350Z
Diagnostic ProcedureNCS00055
1. SELF-DIAGNOSIS
With CONSULT-III
1. Drive vehicle.
2. Stop vehicle and turn ignition switch OFF.
3. Turn ignition switch ON.
4. Select “SELF-DIAG RESULTS” mode for “TRANSMISSION” with CONSULT-III.
Without CONSULT-III
1. Drive vehicle.
2. Stop vehicle and turn ignition switch OFF.
3. Turn ignition switch ON.
4. Perform self-diagnosis. Refer to AT- 9 2 , "
TCM SELF-DIAGNOSTIC PROCEDURE (NO TOOLS)" .
OK or NG
OK >> GO TO 2.
NG >> Check low coast brake solenoid valve circuit and function. Refer to AT- 1 5 3 , "
DTC P1772 LOW
COAST BRAKE SOLENOID VALVE" , AT- 1 5 5 , "DTC P1774 LOW COAST BRAKE SOLENOID
VALVE FUNCTION" .
2. CHECK DTC
Perform AT- 1 4 1 , "
DTC Confirmation Procedure" .
OK or NG
OK >>INSPECTION END
NG >> GO TO 3.
3. CHECK TCM POWER SUPPLY AND GROUND CIRCUIT
Check TCM power supply and ground circuit. Refer to AT- 1 6 2 , "
MAIN POWER SUPPLY AND GROUND CIR-
CUIT" .
OK or NG
OK >> GO TO 4.
NG >> Repair or replace damaged parts.
4. DETECT MALFUNCTIONING ITEM
Check A/T assembly harness connector pin terminals for damage or loose connection with harness connector.
OK or NG
OK >> Replace control valve with TCM. Refer to AT- 2 1 5 , "Control Valve with TCM and A/T Fluid Temper-
ature Sensor 2" .
NG >> Repair or replace damaged parts.

AT-144
DTC P1731 A/T 1ST ENGINE BRAKING
Revision: 2006 November2007 350Z
Diagnostic ProcedureNCS0005B
1. CHECK INPUT SIGNALS
With CONSULT-III
1. Start engine.
2. Select “SELECTION FROM MENU” in “DATA MONITOR” mode for “TRANSMISSION” with CONSULT-III.
3. Drive vehicle in the “M” position (1st gear), and confirm the ON/OFF actuation of “ATF PRES SW 2” and
“ON OFF SOL”.
OK or NG
OK >> GO TO 4.
NG >> GO TO 2.
2. CHECK TCM POWER SUPPLY AND GROUND CIRCUIT
Check TCM power supply and ground circuit. Refer to AT- 1 6 2 , "
MAIN POWER SUPPLY AND GROUND CIR-
CUIT" .
OK or NG
OK >> GO TO 3.
NG >> Repair or replace damaged parts.
3. DETECT MALFUNCTIONING ITEM
Check A/T assembly harness connector pin terminals for damage or loose connection with harness connector.
OK or NG
OK >> Replace control valve with TCM. Refer to AT- 2 1 5 , "Control Valve with TCM and A/T Fluid Temper-
ature Sensor 2" .
NG >> Repair or replace damaged parts.
4. CHECK DTC
Perform AT- 1 4 3 , "
DTC Confirmation Procedure" .
OK or NG
OK >>INSPECTION END
NG >> GO TO 2.
Item name Condition Display value
ON OFF SOLLow coast brake engaged. Refer to AT- 1 9
.ON
Low coast brake disengaged. Refer to AT- 1 9
.OFF
ATF PRES SW 2Low coast brake engaged. Refer to AT- 1 9
.ON
Low coast brake disengaged. Refer to AT- 1 9
.OFF

AT-148
DTC P1757 FRONT BRAKE SOLENOID VALVE
Revision: 2006 November2007 350Z
Diagnostic ProcedureNCS0005T
1. CHECK INPUT SIGNAL
With CONSULT-III
1. Turn ignition switch ON.
2. Select “MAIN SIGNALS” in “DATA MONITOR” mode for “TRANSMISSION” with CONSULT-III.
3. Start engine.
4. Read out the value of “FR/B SOLENOID” while driving.
OK or NG
OK >> GO TO 4.
NG >> GO TO 2.
2. CHECK TCM POWER SUPPLY AND GROUND CIRCUIT
Check TCM power supply and ground circuit. Refer to AT- 1 6 2 , "
MAIN POWER SUPPLY AND GROUND CIR-
CUIT" .
OK or NG
OK >> GO TO 3.
NG >> Repair or replace damaged parts.
3. DETECT MALFUNCTIONING ITEM
Check A/T assembly harness connector pin terminals for damage or loose connection with harness connector.
OK or NG
OK >> Replace control valve with TCM. Refer to AT- 2 1 5 , "Control Valve with TCM and A/T Fluid Temper-
ature Sensor 2" .
NG >> Repair or replace damaged parts.
4. CHECK DTC
Perform AT- 1 4 7 , "
DTC Confirmation Procedure" .
OK or NG
OK >>INSPECTION END
NG >> GO TO 2.
Item name ConditionDisplay value
(Approx.)
FR/B SOLENOIDFront brake engaged. Refer to AT- 1 9
. 0.6 – 0.8 A
Front brake disengaged. Refer to AT- 1 9
. 0 – 0.05 A