2007 NISSAN 350Z Bearing

AT-256
DISASSEMBLY
Revision: 2006 November2007 350Z
6. Remove O-ring from input clutch assembly.
7. Remove tightening bolts for oil pump assembly and transmis-
sion case.
8. Attach the sliding hammers to oil pump assembly and extract it
evenly from transmission case.
CAUTION:

Fully tighten sliding hammer screw.

Make sure that bearing race is installed to the oil pump
assembly edge surface.
9. Remove O-ring from oil pump assembly.
SCIA5011E
SCIA2300E
SCIA5312E
SCIA5172E

DISASSEMBLY
AT-257
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: 2006 November2007 350Z
10. Remove bearing race from oil pump assembly.
11. Remove needle bearing from front sun gear.
12. Remove front sun gear assembly from front carrier assembly.
NOTE:
Remove front sun gear by rotating left/right.
13. Remove seal rings from input clutch assembly.
14. Remove front carrier assembly from rear carrier assembly. (With
input clutch assembly and rear internal gear.)
CAUTION:
Be careful to remove it with needle bearing.
SCIA6529E
SCIA2808E
SCIA5014E
SCIA2470E
SCIA5015E

DISASSEMBLY
AT-259
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: 2006 November2007 350Z
19. Remove needle bearing (front side) from mid carrier assembly.
20. Remove needle bearing (rear side) from mid carrier assembly.
21. Remove bearing race from rear carrier assembly.
22. Remove needle bearing from rear carrier assembly.
23. Remove mid sun gear assembly, rear sun gear assembly and
high and low reverse clutch hub as a unit.
CAUTION:
Be careful to remove then with bearing race and needle
bearing.
SCIA2805E
SCIA2804E
SCIA5175E
SCIA2803E
SCIA5018E

AT-260
DISASSEMBLY
Revision: 2006 November2007 350Z
24. Remove high and low reverse clutch assembly from direct clutch
assembly.
CAUTION:
Make sure that needle bearing is installed to high and low
reverse clutch assembly edge surface.
25. Remove direct clutch assembly from reverse brake.
26. Remove needle bearing from drum support.
27. Remove snap ring from A/T assembly harness connector.
28. Push A/T assembly harness connector.
CAUTION:
Be careful not to damage connector.
SCIA2306E
SCIA5019E
SCIA5198E
SCIA5021E
SCIA5022E

AT-264
DISASSEMBLY
Revision: 2006 November2007 350Z
45. Tap rear extension assembly with soft hammer.
46. Remove rear extension assembly from transmission case. (With
needle bearing)
47. Remove bearing race from output shaft.
48. Remove output shaft from transmission case by rotating left/
right.
49. Remove parking gear from output shaft.
SCIA5028E
SCIA5029E
SCIA5245E
SCIA5030E
SCIA5247E

DISASSEMBLY
AT-265
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: 2006 November2007 350Z
50. Remove seal rings from output shaft.
51. Remove needle bearing from transmission case.
52. Remove revolution sensor from transmission case.
CAUTION:

Do not subject it to impact by dropping or hitting it.

Do not disassemble.

Do not allow metal filings, etc. to get on the sensor's front
edge magnetic area.

Do not place in an area affected by magnetism.
53. Remove reverse brake snap ring (fixing plate) using 2 flat-
bladed screwdrivers.
NOTE:
Press out snap ring from transmission case oil pan side gap
using a flat-bladed screwdriver, and remove it using another
screwdriver.
54. Remove reverse brake retaining plate from transmission case.

Check facing for burns, cracks or damage. If necessary,
replace the plate.
55. Remove N-spring from transmission case.
SCIA5209E
SCIA5031E
SCIA2320E
SCIA5032E
SCIA5214E

AT-266
DISASSEMBLY
Revision: 2006 November2007 350Z
56. Remove reverse brake drive plates, driven plates and dish
plates from transmission case.
CAUTION:
Be careful to remove it with N-spring.
57. Remove snap ring (fixing spring retainer) using a flat-bladed
screwdriver.
58. Remove spring retainer and return spring from transmission
case.
59. Remove seal rings from drum support.
60. Remove needle bearing from drum support edge surface.
SCIA2322E
SCIA2323E
SCIA2324E
SCIA3333E
SCIA2796E

DISASSEMBLY
AT-269
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: 2006 November2007 350Z
70. Remove snap ring from transmission case using pair of snap
ring pliers.
71. Remove servo assembly (with return spring) from transmission
case.
72. Remove return spring from servo assembly.
73. Remove O-rings from servo assembly.
74. Remove needle bearing (1) from rear extension.
SCIA2333E
SCIA5679E
SCIA5717E
SCIA5719E
SCIA6179J