2007 MERCEDES-BENZ SLK55AMG ignition

274 Controls in detail
Useful features
Reprogramming a single signal trans-
mitter button
To program a device using a signal trans-
mitter button previously trained, follow
these steps:
Switch on the ignition (page 37).
Press and hold the desired signal
transmitter button (2, 3 or4).
Do not release the button.
Indicator lamp1 will begin to flash
after 20 seconds. Without releasing
the signal transmitter button, proceed
with programming starting with step 3.Operation of integrated remote control
Switch on the ignition (page 37).
Select and press the appropriate inte-
grated signal transmitter button (2,
3 or4) to activate the remote con-
trolled device.
The integrated remote control trans-
mitter continues to send the signal as
long as the button is pressed – up to
20 seconds.Erasing the integrated remote control
memorySwitch on the ignition (page 37).
Simultaneously press and hold outer
signal transmitter buttons2 and 4,
for approximately 20 seconds, until
indicator lamp1 flashes rapidly. Do
not hold for longer than 30 seconds.
The codes of all three channels are
erased.
iIf you sell your vehicle, erase the codes of all
three channels.

276 Controls in detail
Useful features
Heated steering wheel*
(SLK 280, SLK 350, Canada only)
The steering wheel heating warms up the
leather area of the steering wheel.
The stalk is located on the lower left-hand
side of the steering wheel.
1Switching on
2Indicator lamp
3Switching offSwitching onSwitch on the ignition (page 37).
Turn switch at tip of stalk in direction of
arrow1 and release it.
The steering wheel is heated. Indicator
lamp2 comes on.Switching off
Turn switch at tip of stalk in direction of
arrow3 and release it.
The steering wheel heating is switched
off. Indicator lamp2 goes out.
iThe steering wheel heating is temporarily
suspended while indicator lamp2 remains on
when

the temperature of the vehicle interior is
above 86°F (30°C)

the temperature of the steering wheel is
above 95°F (35°C)
When these conditions do not apply anymore,
steering wheel heating continues.
iIndicator lamp2 flashes or switches off in
case of

power surge or undervoltage

steering wheel heating malfunction
iThe steering wheel heating switches off
automatically when you remove the SmartKey
from the starter switch.

294 Operation
Engine compartment
Hood
Opening
1Hood lock release lever
Warning!G
Do not pull the release lever while the vehi-
cle is in motion. Otherwise the hood could
be forced open by passing air flow.
This could cause the hood to come loose
and injure you and/or others.
Warning!G
If you see flames or smoke coming from the
engine compartment, or if the coolant tem-
perature gauge indicates that the engine is
overheated, do not open the hood. Move
away from the vehicle and do not open the
hood until the engine has cooled. If neces-
sary, call the fire department.
Warning!G
You could be injured when the hood is open
– even when the engine is turned off.
Parts of the engine can become very hot. To
prevent burns, let the engine cool of com-
pletely before touching any components on
the vehicle. Comply with all relevant safety
precautions.
Warning!G
To help prevent personal injury, stay clear of
moving parts when the hood is open and the
engine is running.
The radiator fan may continue to run for
approximately 30 seconds or may even
restart after the engine has been turned off.
Stay clear of fan blades.
Warning!G
The engine is equipped with a transistorized
ignition system. Because of the high voltage
it is dangerous to touch any components (ig-
nition coils, spark plug sockets, diagnostic
socket) of the ignition system

with the engine running

while starting the engine

if ignition is “on” and the engine is
turned manually

296 Operation
Engine compartment
Engine oil
The amount of oil your engine needs will
depend on a number of factors, including
driving style. Higher oil consumption can
occur when

the vehicle is new

the vehicle is driven frequently at
higher engine speeds
Engine oil consumption checks should only
be made after the vehicle break-in period.Checking engine oil level with the
control system (SLK 55 AMG only)
When checking the oil level

the vehicle must be parked on level
ground.

with the engine at operating tempera-
ture, the vehicle must have been sta-
tionary for at least 5 minutes with the
engine turned off.

with the engine not at operating tem-
perature, the vehicle must have been
stationary for at least 30 minutes with
the engine turned off.To check the engine oil level via the
multifunction display, do the following:
Switch on the ignition (page 37).
The standard display appears in the
multifunction display (
page 127).
Press buttonk orj on the mul-
tifunction steering wheel repeatedly
until the following message appears in
the multifunction display (
page 122):
!Do not use any special lubricant additives,
as these may damage the drive assemblies.
Using special additives not approved by
Mercedes-Benz may cause damage not covered
by the Mercedes-Benz Limited Warranty.
More information on this subject is available at
any authorized Mercedes-Benz Center.

297 Operation
Engine compartment
One of the following messages will
subsequently appear in the multifunc-
tion display:

Engine oil level
OK

Add 1.0 qt. (Canada: 1.0 liter)
to reach max. oil level

Add 1.5 qts. (Canada:
1.5 liters)
to reach max. oil level

Add 2.0 qts. (Canada:
2.0 liters)
to reach max. oil level
If necessary, add engine oil.
For adding engine oil, see “Adding
engine oil” (
page 299).
For more information on engine oil, see
“Fuels, coolants, lubricants, etc.”
(
page 443).Other display messages
If the ignition is not switched on, the fol-
lowing message will appear:
Turn on ignition
to see engine oil level
Switch on the ignition (page 37).
If you see the message:
Observe waiting time
If engine is at operating temperature,
wait 5 minutes before repeating check
procedure.
If engine is not at operating tempera-
ture yet, you must wait 30 minutes
before checking oil.If you see the message:
Cannot check engine
level with engine on
Turn off the engine.
If the engine is at operating tempera-
ture, wait 5 minutes before checking
oil.
If the engine is not at operating
temperature yet, you must wait
30 minutes before checking oil.
iIf you want to interrupt the checking
procedure, press buttonk orj on the
multifunction steering wheel (
page 122).
iIf you want to interrupt the checking
procedure, press buttonk orj on the
multifunction steering wheel (
page 122).

316 Operation
Tires and wheels
Reactivating the Run Flat Indicator
The tire inflation pressure monitor must be
restarted in the following situations:

If you have changed the tire inflation
pressure

If you have replaced the wheels or tires

If you have installed new wheels or
tires
Using the Tire and Loading Information
placard on the driver’s door B-pillar or,
if available, the tire inflation pressure
label on the inside of the fuel filler flap,
make sure the tire inflation pressure of
all four tires is correct.
Switch on the ignition (page 37).
The standard display menu appears in
the multifunction display (
page 127).
Press buttonk orj repeatedly
until the following message appears in
the multifunction display:
Run Flat Indicator
active
Menu: R-Button
Press reset buttonJ (page 26).
The following message will appear in
the multifunction display:
Restart
Run Flat Indicator? If you wish to confirm activation:
Press buttonæ.
The following message will appear in
the multifunction display:
Run Flat Indicator
restarted
After a certain “learning phase”, the Run
Flat Indicator checks the set pressure val-
ues for all four tires.
If you wish to cancel activation:
Press buttonç.
or
Wait until the message
Restart
Run Flat Indicator?
disappears.Warning!G
The Run Flat Indicator can only warn you in
a reliable manner if you have set the correct
tire inflation pressures for each tire.
If an incorrect tire inflation pressure was
set, the system will monitor the pressure
according to the incorrect value.

334 Operation
Maintenance
We strongly recommend that you have
your vehicle serviced by an authorized
Mercedes-Benz Center, in accordance with
the Maintenance Booklet at the times
called for by the maintenance service indi-
cator.Maintenance service indicator
message
The maintenance service indicator
message will notify you when the next
maintenance service is due.
Starting approximately 1 month before the
next maintenance service is due, one of
the following messages will appear in the
multifunction display while you are driving
or when you switch on the ignition (exam-
ple service A):
Service A due in XXXXX miles (km)
Service A due in XXX days
Service A due in X day
Service A due now
The maintenance services will be indicated
by showing a service type A through
type H in the multifunction display.
Types A through H are classified based on
estimated time needed to perform the
maintenance service, ranging:
from
Service A
(approximately 1 hour)
to
Service H
(approximately 8 hours)
Refer to Maintenance Booklet for a listing
of maintenance services and intervals the
need to be performed at.
!Failure to have the vehicle maintained in
accordance with the Maintenance Booklet and
the maintenance service indicator at the
designated times/mileage will result in vehicle
damage not covered by the Mercedes-Benz
Limited Warranty.
iThe Maintenance System tracks distance
driven and the time elapsed since the last main-
tenance service, calculates other maintenance
service work required, and calls for the next
maintenance service accordingly.

335 Operation
Maintenance
Clearing the maintenance service
indicator message
The maintenance service indicator
message is automatically cleared:

after approximately 10 seconds when
you switch on the ignition or when
reaching the service threshold while
driving

after approximately 30 seconds once
the suggested maintenance service
term has passed
You can also clear it yourself.
Press reset buttonJ(page 26) on
the instrument cluster.
The maintenance service indicator
message is cleared and the standard
display appears in the multifunction
display (
page 127).
Maintenance service term exceeded
If you have exceeded the suggested main-
tenance service term, you will see the fol-
lowing message in the multifunction
display:
Service A exceeded by XXXXX miles (km)
Service A exceeded by XXX days
Service A exceeded by X day
In addition, a signal sounds when the
message appears.
Any authorized Mercedes-Benz Center will
reset the maintenance service indicator
following a completed maintenance
service.Calling up the maintenance service
indicator display
You can call up the maintenance service in-
dicator display at any time to check when
the next maintenance service is due.
Switch on the ignition (page 37).
The standard display menu appears in
the multifunction display (
page 127).
Press buttonjork on the mul-
tifunction steering wheel repeatedly
until the maintenance service indicator
display with the service symbol 9
appears in the multifunction display.
iThe menu overview can be found on
(
page 124).