2007 MERCEDES-BENZ SL65AMG lock

409 Practical hints
Flat tire

Keeping jack in this position, turn
crank3 clockwise until the jack base
meets the ground. Make sure the jack
is vertical (plumb line).

Continue to turn the crank until the tire
is a maximum of 1.2 in (3 cm) from the
ground.Removing the wheel
1Alignment bolt

Unscrew upper-most wheel bolt and re-
move.

Replace this wheel bolt with alignment
bolt1 supplied in the tool kit.

Remove the remaining bolts.

Remove the wheel.Mounting the new wheel

Clean contact surfaces of wheel and
wheel hub.

Guide the spare wheel onto the align-
ment bolt and push it on.

Insert wheel bolts and tighten them
slightly.
!
Do not place wheel bolts in sand or dirt. This
could result in damage to the bolt and wheel hub
threads.
Warning!
G
Inflate spare wheel tire only after the wheel
is properly mounted.
Inflate the spare wheel tire using the electric
pump (
page 410) before
lowering the ve-
hicle.

412 Practical hintsFlat tireLowering the vehicle
Lower vehicle by turning crank coun-
terclockwise until the full weight of the
vehicle is resting on the ground.

Pull the jack out of the jack support
tube.
1 - 5 Wheel bolts

Tighten the five wheel bolts evenly, fol-
lowing the diagonal sequence illustrat-
ed (1 to 5), until all bolts are tight.
Observe a tightening torque of 96 lb-ft
(130 Nm).

Before storing the jack in the trunk,
crank back to storage position and fold
in the arm.
Replacing jack support tube cover

Slide tongue of cover under the upper
edge of the tube opening.

Applying even pressure, press cover
until it snaps into place.
Be careful not to damage the locking
tabs or clamp the plastic retaining
strap.
i
The flat tire may be transported in the trunk
when the retractable hardtop is raised. If avail-
able, use a protective sheet on the spare wheel.
Vehicles with TPMS or Advanced TPMS*:
Do not activate the tire inflation pressure moni-
tor until a full size wheel/tire with functioning
sensor has been placed back into service on the
vehicle.
Warning!
G
Have the tightening torque checked after
changing a wheel. The wheels could come
loose if they are not tightened to a torque of
96 lb-ft (130 Nm).Warning!
G
When turning the wheel wrench to tighten
the wheel bolts, make sure you position
hands on the wrench in such a way that you
avoid injury to yourself, such as scraping
your hands against the wheel. Make sure
turning the wheel wrench will not scratch or
damage the wheel rim.
i
For information on storing the spare wheel
back into the trunk, see “Storing the spare wheel
after use” (
page 390).


416 Practical hintsBatteries
Disconnecting the batteries
Apply the parking brake (
page 61).

Make sure the gear selector lever is set
to position P (
page 168).

Close the retractable hardtop
(page 199).

Turn off all electrical consumers.

Turn off the engine (
page 62).

Remove the SmartKey from the starter
switch.
Vehicles with KEYLESS-GO*: Open
the driver’s door.

Open the trunk.

Read and observe safety instructions
and precautions (
page 281).

Open the luggage cover in the trunk
(page 206).

Remove the trunk floor.
The battery for electrical consumers is
located in the right hand area of the
trunk (
page 388).

Use the 10 mm open-end wrench from
the vehicle tool kit to disconnect the
negative lead from negative
terminal5 of the consumer battery
(page 414).
Warning!
G
With a disconnected battery

you will no longer be able to turn the
SmartKey in the starter switch and
pressing the KEYLESS-GO* start/stop
button on the gear selector lever will
have no effect


the gear selector lever will remain
locked in positionP
!
Always disconnect the batteries in the order
described below, even if you only want to charge
the starter battery, for example. Otherwise the
vehicle’s electronics can be damaged.

421 Practical hints
Towing the vehicle
Towing the vehicle
Mercedes-Benz recommends that the vehi-
cle be transported with all wheels off the
ground using flatbed or appropriate wheel
lift/dolly equipment.When circumstances do not permit the
recommended towing methods, the vehi-
cle may be towed with all wheels on the
ground or front wheels raised only so far as
necessary to have the vehicle moved to a
safe location where the recommended
towing methods can be employed.!
Use flatbed or wheel lift/dolly equipment
with SmartKey in starter switch turned to
position0.
Do not tow with sling-type equipment. Towing
with sling-type equipment over bumpy roads will
damage radiator and supports.
To prevent damage during transport, do not tie
down vehicle by its chassis or suspension parts.
Switch off the tow-away alarm and the automatic
central locking.
!
If the vehicle is towed with the front axle
raised, the gear selector lever must be in
positionN and the engine must be shut off
(SmartKey in starter switch position0 or1).
Otherwise, the ESP
® will immediately be en-
gaged and will apply the rear wheel brakes.
When towing the vehicle with all wheels on the
ground, the gear selector lever must be in
positionN and the SmartKey must be in starter
switch position2.
When towing the vehicle with all wheels on the
ground or the front axle raised, the vehicle
may be towed only for distances up to
30 miles (50 km) and at a speed not to exceed
30 mph (50 km/h).
To be certain to avoid a possibility of damage to
the transmission, however, we recommend the
drive shaft be disconnected at the rear axle drive
flange for any towing beyond a short tow to a
nearby garage.
Warning!
G
If circumstances require towing the vehicle
with all wheels on the ground, always tow
with a tow bar if:

the engine will not run


there is a malfunction in the
electro-hydraulic brake system


there is a malfunction in the power sup-
ply or in the vehicle’s electrical system
as that will be necessary to adequately con-
trol the towed vehicle.
Prior to towing the vehicle with all wheels on
the ground, make certain that the SmartKey
is in starter switch position2.
If the SmartKey is left in starter switch
position0 for an extended period of time, it
can no longer be turned in the switch. In this
case, the steering is locked. To unlock, re-
move SmartKey from starter switch and re-
insert.

422 Practical hintsTowing the vehicleWarning!
G
The brake system requires electrical power
to operate.
A malfunction in the vehicle’s power supply
or electrical system may impair brake sys-
tem operation and switch it into its emer-
gency operation mode. To brake, the driver
must then apply significantly greater brake
pedal pressure and depress the pedal much
further to obtain the expected braking ef-
fect. If necessary, apply full pressure to the
brake pedal. Brakes are only applied to the
front wheels. Stopping distance is
increased! Adapt your driving style
accordingly. For more information, see
“Electro-hydraulic brake system”
(page 92).
With the engine not running, there is no
power assistance for the brake and steering
systems. In this case, it is important to keep
in mind that a considerably higher degree of
effort is necessary to brake and steer the ve-
hicle. Adapt your driving accordingly.
!
When towing the vehicle with all wheels on
the ground, please note the following:
With the automatic central locking activated and
the SmartKey in starter switch position2, or
KEYLESS-GO* start/stop button in position2,
the vehicle doors lock if the left front wheel as
well as the right rear wheel are turning at vehicle
speeds of approx. 9 mph (15 km / h) or more.
To prevent the vehicle door locks from locking,
deactivate the automatic central locking
(
page 119).
Towing of the vehicle should only be done using
the properly installed towing eye bolt. Never
attach tow cable, tow rope or tow rod to the
vehicle chassis, frame or suspension parts.
i
To signal turns while being towed with the
hazard warning flasher in use, turn SmartKey in
starter switch to position2 and activate the
combination switch for the left or right turn
signal in the usual manner – only the selected
turn signal will operate.
Upon canceling the turn signal, the hazard warn-
ing flasher will operate again.
i
If the battery is disconnected or discharged


the SmartKey will not turn in the starter
switch


the gear selector lever will remain locked in
positionP.
For more information, see “Batteries”
(
page 414) and “Jump starting” (
page 419).

423 Practical hints
Towing the vehicle
Installing towing eye bolt
FrontExample illustration (SL 550 and SL 600
without Sport Package)1Cover on passenger side of front
bumper
To remove cover:
Press mark on cover 1 in direction of
arrow.

Lift cover1off to reveal the threaded
hole for towing eye bolt.To reinstall cover:

Fit locking tabs of cover under the
lower edge of the opening in the
bumper.

Apply even pressure on the upper part
of the cover until it snaps into place.
Rear
1Cover on passenger side of rear
bumper
To remove cover:

Insert flat, blunt object as a lever into
upper left or right recess of cover 1.

Loosen cover 1 using the lever.

Fold cover 1 down in direction of ar-
row to reveal the threaded hole for the
towing eye bolt.
To reinstall cover:

Fit cover 1 and snap into place.
Installing towing eye bolt

Take the towing eye bolt and the wheel
wrench from the vehicle tool kit
(page 388).

Screw towing eye bolt into threaded
hole to its stop.

Insert wheel wrench into towing eye
and tighten towing eye bolt by turning
it clockwise.
Removing towing eye bolt

Take the wheel wrench from the
vehicle tool kit (
page 388).

Insert wheel wrench into towing eye
and loosen towing eye bolt by turning it
counterclockwise.

Remove towing eye bolt.

425 Practical hintsFuses
Fuse boxes in engine compartment
Open the hood (
page 274).
The fuse boxes are located on the driver’s
and passenger side in front of the bulk-
head (wall separating the engine and pas-
senger compartment).
Fuse box on driver’s side1Fuse box cover
2Locking
3Unlocking
Fuse box on passenger side1Fuse box cover
2Locking
3UnlockingOpening

Move slide to position 3 and lift
cover1.
Closing

Hook cover 1 onto tabs and close it.

Move slide to position 2.

Close the hood after checking or re-
placing fuses (
page 275).
!
The fuse box cover must be properly posi-
tioned with the slide at the ‹ symbol to pre-
vent moisture or dirt from entering the fuse box
and possibly impairing fuse operation.

453 Index
A
ABC 225
Messages in display 349
Oil level 279
ABS 87
Indicator lamp 29, 334
Messages in the multifunction
display 351, 352
Warning lamp 27, 332
Accelerator position, automatic
transmission 171
Accessory weight 312
Accident 59
Active Body Control see ABC
Air bags 68
Children in the vehicle 83
Front 71
Front passenger front air bag off
indicator lamp 76
Head-thorax 72
Knee bag 72
Occupant Classification System
(OCS) 72
Passenger 72
Air conditioning system see Automatic cli-
mate control systemAir distribution 188, 189
Air pressure 312
Tire inflation pressure 291
Air pump 410
Air recirculation mode 191
Air vents 185
Air volume 188, 190
Alarm system see Anti-theft systems
Alignment bolt (vehicle tool kit) 409
Anticorrosion/antifreeze 445, 451
Antiglare, Interior rear view mirror 180
Antilock Brake System see ABS
Anti-theft systems
Anti-theft alarm system 96
Immobilizer 96
Tow-away alarm 98
Aquaplaning see Hydroplaning
Armrest 234
Ashtray 31, 239
Aspect ratio 312
ATF 279
Auto-dimming, Rear view mirrors 180
Automatic central locking 119
Control system 162Automatic climate control system 184
Air conditioning, Cooling 193
Air conditioning refrigerant 446
Air distribution 188, 189
Air recirculation mode 191
Air vents 185
Air volume 188, 190
Control panel 185
Deactivating system 187
Defrosting 183, 190
Residual heat utilization 194
Temperature 188
Temperature sensor 33
Ventilated glove box 195
Automatic lighting control, Interior
lighting 135
Automatic locking when driving 119
Automatic shift program 173
Automatic transmission 168
Accelerator position 171
Comfort program mode 173
Emergency operation
(Limp-Home Mode) 179
Gear ranges 172
Gear selector lever 32, 168
Gear selector lever position 168, 170