2007 MERCEDES-BENZ R320CDI light

248 Controls in detail
3-zone automatic climate control*
Setting the temperature
Use temperature controla (
page 245)
to separately adjust the air temperature of
the rear passenger compartment.
You should raise or lower the temperature
setting in small increments, preferably
starting at 72°F (22°C). The automatic
climate control will adjust to the set
temperature as fast as possible.Increasing the temperatureTurn temperature controla
(
page 245) slightly clockwise.
The rear automatic climate control will
correspondingly adjust the interior air
temperature for the rear passenger
compartment.
Decreasing the temperature
Turn temperature controla
(
page 245) slightly counterclock-
wise.
The rear automatic climate control will
correspondingly adjust the interior air
temperature for the rear passenger
compartment.Adjusting air volume
Adjusting manually
Five blower speeds are available.
Press button
to decrease or
buttonQ to increase air volume to
the desired level.
The indicator lamp on buttonU
goes out. The selected blower speed is
shown by the indicator lamps for air
volume settings 9 (
page 245).
Adjusting automatically
Press buttonU.
The indicator lamp on the button
comes on. The air volume is adjusted
automatically.
iThe rear automatic climate control will not
cool the air when the air conditioning is switched
off (
page 243).

251 Controls in detail
Power windows
Power windows
Opening and closing
The door windows and the hinged quarter
windows* are opened and closed electri-
cally. The switches for all door windows
and the hinged quarter windows* are
located on the driver’s door control panel
(
page 36). The switches for the respec-
tive door windows are located on the
control panels of the front passenger door
and the rear doors. The hinged quarter
windows* can be operated from the
driver’s seat only.1Left front door window
2Right front door window
3Right rear door window
4Hinged quarter windows*
5Override switch (
page 97)
6Left rear door window
Switch on the ignition (page 39).
Warning!G
When closing the windows, make sure that
there is no danger of anyone being harmed
by the closing procedure.
Activate the override switch (
page 97)
when children are riding in the back seats of
the vehicle. The children could otherwise in-
jure themselves, e.g. by becoming trapped
in the window opening.
The closing of a door window can be imme-
diately halted by releasing the switch or, if
switch was pulled past the resistance point
and released, by either pressing or pulling
the respective switch.
If a door window encounters an obstruction
that blocks its path in a circumstance where
you pulled the switch past the resistance
point and released it to close the door win-
dow, the automatic reversal function will
stop the door window and open it slightly.


253 Controls in detail
Power windows
Fully opening the door windows
(Express-open)
Press switch1, 2, 3, or6
(
page 251) past the resistance point
and release.
The corresponding door window opens
completely.
Fully closing the door windows
(Express-close)
Pull switch1, 2, 3, or6
(
page 251) past the resistance point
and release.
The corresponding door window closes
completely.If the upward movement of a door window
is blocked during the closing procedure,
the door window will stop and open
slightly.
Remove the obstruction.
Pull the respective power window
switch past the resistance point again
and release.
Stopping door windows during
Express-operation
Press or pull the respective door
window switch again.Hinged quarter windows*
The switches for opening and closing the
hinged quarter windows are located on the
door control panel of the driver’s door
(
page 36).
1Hinged quarter windows: opening
2Hinged quarter windows: closing
Warning!G
Driver’s door only:
If within 5 seconds switch is again pulled
past the resistance point and released, the
automatic reversal will not function.
iIf the door window still does not close when
there is no obstruction, pull and hold the respec-
tive power window switch. The door window will
then close without the obstruction sensor
function.

254 Controls in detail
Power windows
Opening
Press and release switch 1.
To stop the hinged quarter window:
Press and release switch 1 once
more.
Closing
Press and release switch 2.
To stop the hinged quarter window:
Press and release switch 2 once
more.
Synchronizing the door windows
The door windows must be synchronized

after the battery was disconnected

if the door windows cannot be fully
opened (Express-open) or closed
(Express-close)
Close all doors.
Switch on the ignition (page 39).
Pull and hold door window switch1,
2, 3, or6 (
page 251).
Once a door window is closed
completely, hold the respective switch
for approximately 3 seconds.
The door window is synchronized.
Summer opening feature
If the weather is warm, you can ventilate
the vehicle before driving off by simulta-
neously

opening the door windows

opening the hinged quarter windows*

opening the tilt/sliding sunroof*
(or tilt/sliding panel*)

switching on the seat ventilation* for
the driver’s seat
iWhen the obstruction sensor detects the
hinged quarter window is blocked during the
closing process, it will stop and open slightly.
iEach door window must be synchronized
separately.

258 Controls in detail
Power tilt/sliding sunroof*
Opening and closing
Warning!G
When closing the tilt/sliding sunroof, make
sure that there is no danger of anyone being
harmed by the closing procedure.
If the tilt/sliding sunroof encounters an
obstruction that blocks its path in a circum-
stance where you are closing the tilt/sliding
sunroof by moving the tilt/sliding sunroof
switch past the resistance point, or by
pressing and holding button‹on the
SmartKey, by pressing and holding the lock
button (vehicles with KEYLESS-GO*) on the
door handle, the automatic reversal function
will not operate.
The opening/closing procedure of the
tilt/sliding sunroof can be immediately
halted by releasing the switch or, if the
switch was moved past the resistance point
and released, by moving the switch in any
direction.
The tilt/sliding sunroof is made out of glass.
In the event of an accident, the glass may
shatter. This may result in an opening in the
roof.
In a vehicle rollover, occupants not wearing
their seat belts or not wearing them properly
may be thrown out of the opening. Such an
opening also presents a potential for injury
for occupants wearing their seat belts prop-
erly as entire body parts or portions of them
may protrude from the passenger compart-
ment.
When leaving the vehicle, always remove the
SmartKey or SmartKey with KEYLESS-GO*
from the starter switch, take it with you, and
lock your vehicle. Do not leave children
unattended in the vehicle, or with access to
an unlocked vehicle. Unsupervised use of
vehicle equipment can cause an accident
and/or serious personal injury.!To avoid damaging the seals, do not trans-
port any objects with sharp edges which can
stick out of the tilt/sliding sunroof.
Do not open the tilt/sliding sunroof if there is
snow or ice on the roof, as this could result in
malfunctions.
The tilt/sliding sunroof can be opened or closed
manually should an electrical malfunction occur
(
page 481).
iWhen the tilt/sliding sunroof is open,
resonance noises may result in addition to the
usual wind noises. They are caused by minimal
pressure changes in the passenger compart-
ment. To reduce or eliminate theses noises,
change the position of the tilt/sliding sunroof or
open a door window slightly.
iYou can also open or close the tilt/sliding
sunroof using the SmartKey or the
KEYLESS-GO* function, see “Summer opening
feature” (
page 254) and “Convenience clos-
ing feature” (
page 256). Depending on the
current position, the tilt/sliding sunroofs may
also open or close when the air recirculation
button: on the control panel of the climate
control (
page 220) or automatic climate
control (
page 234) is pressed and held.

259 Controls in detail
Power tilt/sliding sunroof*
The tilt/sliding sunroof is opened and
closed electrically. The switch for the
tilt/sliding sunroof is located on the
overhead control panel.
Sunroof switch
1Push back to slide sunroof open
2Push forward to slide sunroof closed
3Push up to raise sunroof at rear
4Pull down to lower sunroof at rear
With the sunroof closed or tilted open, a
screen can be slid into the roof opening to
guard against sun rays. When sliding the
sunroof open, the screen will also retract.
Switch on the ignition (page 39).
Opening and closing
To open, close, raise, or lower the
tilt/sliding sunroof, move the sunroof
switch to the resistance point in the
required direction of arrows1to4
(
page 259).
Release the sunroof switch when the
tilt/sliding sunroof has reached the
desired position.Fully opening (Express-open) and
closing (Express-close)
To fully open or close the tilt/sliding
sunroof, move the sunroof switch past
the resistance point in the required
direction1or2 (
page 259) and
release.
The tilt/sliding sunroof opens or closes
completely.
Stopping the power tilt/sliding sunroof
during Express-open
Move the sunroof switch in any
direction.
The movement of the tilt/sliding
sunroof stops.
iIf the movement of the tilt/sliding sunroof is
blocked during the closing procedure, the
tilt/sliding sunroof will stop and reopen slightly.

262 Controls in detail
Panorama roof with power tilt/sliding panel*
Opening and closing the panorama roof
with power tilt/sliding panel
Switch on the ignition (page 39).
The tilt/sliding panel is opened and closed
electrically. The switch for the tilt/sliding
panel is on the overhead control panel.
The tilt/sliding panel only operates with
the roller sunblinds opened.
Warning!G
When opening or closing the tilt/sliding
panel, make sure that there is no danger of
anyone being harmed by the opening or
closing procedure.
The opening procedure of the tilt/sliding
panel can be immediately halted by releas-
ing the switch or, if the switch was moved
past the resistance point and released, by
moving the switch in any direction.
The closing procedure of the tilt/sliding
panel can be immediately halted by releas-
ing the switch.
The panorama roof with power tilt/sliding
panel is made out of glass. In the event of
an accident, the glass may shatter. This may
result in an opening in the roof.
In a vehicle rollover, occupants not wearing
their seat belts or not wearing them properly
may be thrown out of the opening. Such an
opening also presents a potential for injury
for occupants wearing their seat belts
properly as entire body parts or portions of
them may protrude from the passenger
compartment.
When leaving the vehicle, always remove the
SmartKey or the SmartKey with
KEYLESS-GO* from the starter switch, take
it with you, and lock the vehicle. Do not
leave children unattended in the vehicle, or
with access to an unlocked vehicle.
Unsupervised use of vehicle equipment can
cause an accident and/or serious personal
injury.
!To avoid damaging the seals, do not trans-
port any objects with sharp edges which can
stick out of the tilt/sliding panel.
Do not open the tilt/sliding panel if there is
snow or ice on the roof, as this could result in
malfunctions.
iWhen the tilt/sliding panel is open,
resonance noises may result in addition to the
usual wind noises. They are caused by minimal
pressure changes in the passenger compart-
ment. To reduce or eliminate theses noises,
change the position of the tilt/sliding panel or
open a door window slightly.
iYou can also open or close the tilt/sliding
panel using the SmartKey or the KEYLESS-GO*
function, see “Summer opening feature”
(
page 254) and “Convenience closing
feature” (
page 256).
iThe tilt/sliding panel may also open when
using the air recirculation button:on the
control panel of the climate control
(
page 220) or automatic climate control
(
page 234).

264 Controls in detail
Panorama roof with power tilt/sliding panel*
Synchronizing the panorama roof with
power tilt/sliding panel
The tilt/sliding panel and its roller
sunblinds must be synchronized

after the battery has been
disconnected or discharged

after a malfunction

if the tilt/sliding panel does not open
smoothly
Switch off the ignition (page 40) and
remove the SmartKey from the starter
switch.
Vehicles with KEYLESS-GO*:
Switch off the ignition (page 41).
Open the driver’s door (this puts
the starter switch in position 0,
same as with the SmartKey re-
moved from the starter switch). The
driver’s door then can be closed
again.
Remove the fuse for the tilt/sliding
panel from the fuse box (
page 521).
Reinsert the fuse in the fuse box.
Switch on the ignition (page 39).
Push and hold the roof panel switch in
direction of arrow2 (
page 263)
until the roller sunblinds are fully
closed.
Keep holding the roof panel switch in
direction of arrow2 (
page 263) for
approximately 1 second.
Pull and hold the roof panel switch in
direction of arrow1 (
page 263)
until the roller sunblinds are fully
opened.
Keep holding the roof panel switch in
direction of arrow1 (
page 263) for
approximately 1 second.
!Do not attempt to open or close the
tilt/sliding panel before the tilt/sliding panel is
properly synchronized. The tilt/sliding panel
could otherwise lock-up in the open position.
If the tilt/sliding panel cannot be closed or
synchronized, see an authorized Mercedes-Benz
Light Truck Center or call Roadside Assistance
(
page 333).
iFor information on which fuse box contains
the fuse for the power tilt/sliding panel, see the
fuse chart provided with the vehicle tool kit
(
page 473).