2007 MERCEDES-BENZ CLS63AMG engine

375 Practical hints
What to do if …
Display symbol
Display messages
Possible cause/consequence
Possible solution
Z
Coolant
Stop, turn engine off
The poly-V-belt could be broken.

Stop the vehicle in a safe location and immediately
turn off the engine.

Check the poly-V-belt.
If it is broken:

Do not continue to drive. Otherwise the engine will
overheat due to an inoperative water pump which
may result in damage to the engine. Notify an au-
thorized Mercedes-Benz Center.
If it is intact:

Do not continue to drive the vehicle with this mes-
sage displayed. Doing so could result in serious en-
gine damage that is not covered by the
Mercedes-Benz Warranty.

Observe the coolant temperature indicator in the
instrument cluster (
page 26).

Drive immediately to the nearest authorized
Mercedes-Benz Center.

376 Practical hintsWhat to do if …Display symbol
Display messages
Possible cause/consequence
Possible solution
Z
The cooling fan for the coolant is
malfunctioning.

Observe the coolant temperature indicator in the
instrument cluster (
page 26).
If the coolant temperature is under 120°C, you may
continue driving to an authorized Mercedes-Benz
Center.

Avoid placing heavy loads on the engine (e.g. by
driving uphill) as well as stop-and-go traffic.

Have the fan replaced as soon as possible.
±
Display malfunction
Visit workshop
Certain electronic systems are
unable to relay information to
the control system. The follow-
ing systems may have failed:

Coolant temperature display


Tachometer


Cruise control display

Have the electronic systems checked by an autho-
rized Mercedes-Benz Center.
Engine
Service
There may be a malfunction in:

the fuel injection system


the ignition system


the exhaust system

Have the engine checked as soon as possible by an
authorized Mercedes-Benz Center.

377 Practical hints
What to do if …
When the
Check oil level - at next re-
fueling message appears while the en-
gine is running and at operating
temperature, the engine oil level has
dropped to approximately the minimum
level.
When this occurs, the warning will first
come on intermittently and then stay on if
the oil level drops further.If no oil leaks are noted, continue to drive
to the nearest service station where the
engine oil should be topped to the required
level with an approved engine oil.
For information on approved engine oils,
refer to the Factory Approved Service
Products pamphlet (USA only) or contact
an authorized Mercedes-Benz Center.
Display symbol
Display messages
Possible cause/consequence
Possible solution
:
Check oil level
at next refueling
There is no oil in the engine. There is
a danger of engine damage.

Check the engine oil level (
page 288) and
add engine oil as required (page 289).

If you must add engine oil frequently, have
the engine checked for possible leaks.!
The engine oil level warnings should not be
ignored. Extended driving with the symbol dis-
played could result in serious engine damage
that is not covered by the Mercedes-Benz Limit-
ed Warranty.

379 Practical hints
What to do if …
Display symbol
Display messages
Possible cause/consequence
Possible solution
F
Please don't
forget your key
This display appears (for a maximum of
60 seconds) if the driver’s door is opened
with the engine turned off and no
SmartKey in the starter switch.
This message is only a reminder.

Take the SmartKey or SmartKey with
KEYLESS-GO* with you when leaving
the vehicle.
Change
key batteries
The SmartKey with KEYLESS-GO* batter-
ies are discharged.

Replace the batteries (
page 402).
Key
not recognized
The SmartKey with KEYLESS-GO* is not
recognized while the engine is running
because

the SmartKey with KEYLESS-GO* is
not in the vehicle


there is strong radio-frequency inter-
ference

Stop the vehicle as soon as it is safe
to do so.

Search for the SmartKey.
Otherwise the vehicle cannot be cen-
trally locked nor can the engine be
started again after the engine is
stopped.
Key
not recognized
The SmartKey with KEYLESS-GO* is mo-
mentarily not recognized.

Change the position of the SmartKey
in the vehicle.

Operate the vehicle with the
SmartKey in the starter switch if nec-
essary.

380 Practical hintsWhat to do if …Display symbol
Display messages
Possible cause/consequence
Possible solution
F
Change
key batteries
The SmartKey with KEYLESS-GO* batter-
ies are discharged.

Replace the batteries (
page 402).
Key
not detected
The SmartKey with KEYLESS-GO* is not
recognized while the engine is running
because

the SmartKey with KEYLESS-GO* is
not in the vehicle


there is strong radio-frequency inter-
ference

Stop the vehicle as soon as it is safe to
do so.

Search for the SmartKey.
Otherwise the vehicle cannot be cen-
trally locked nor can the engine be
started again after the engine is
stopped.
Key
not detected
The SmartKey with KEYLESS-GO* is mo-
mentarily not recognized.

Change the position of the SmartKey in
the vehicle.

Operate the vehicle with the SmartKey
in the starter switch if necessary.
.
Active headlamps
inoperative
The active Bi-Xenon* headlamp system is
malfunctioning.

Contact an authorized Mercedes-Benz
Center as soon as possible.
Active headlamps
The active Bi-Xenon* headlamps are mal-
functioning.

Contact an authorized Mercedes-Benz
Center as soon as possible.

412 Practical hintsFlat tirePreparing the vehicle
Park the vehicle in a safe distance from
moving traffic on a hard, flat surface
when possible.

Turn on the hazard warning flashers.

Turn the steering wheel so that the
front wheels are in a straight ahead
position.

Set the parking brake.

Move the gear selector lever to P.
Vehicles with SmartKey:

Turn off the engine (
page 60).

Remove the SmartKey from the starter
switch.Vehicles with KEYLESS-GO*:

Turn off the engine by pressing the
KEYLESS-GO* button on the gear
selector lever once (
page 60).

Open the driver’s door (this puts the
starter switch in position 0, same as
with the SmartKey removed from the
starter switch). The driver’s door then
can be closed again.

Have any passenger exit the vehicle at
a safe distance from the roadway.
Mounting the spare wheel
i
Open door only when conditions are safe to
do so.
Warning!
G
The dimensions of the spare wheel
(Minispare or collapsible tire) are different
from those of the road wheels. As a result,
the vehicle handling characteristics change
when driving with a spare wheel mounted.
Adapt your driving style accordingly.
The spare wheel is for temporary use only.
When driving with spare wheel mounted,
ensure proper tire pressure and do not ex-
ceed a vehicle speed of 50 mph (80 km/h).
Drive to the nearest Mercedes-Benz Center
as soon as possible to have the spare wheel
replaced with a regular road wheel.
Never operate the vehicle with more than
one spare wheel mounted.
Do not switch off the ESP
® when a Minis-
pare or collapsible tire is mounted.

415 Practical hints
Flat tire

Jack up the vehicle until the wheel is a
maximum of 1.2 in (3 cm) from the
ground. Never start engine while
vehicle is raised.Removing the wheel
1Alignment bolt

Unscrew the upper-most wheel bolt
and remove.

Replace this wheel bolt with alignment
bolt1 supplied in the tool kit.

Remove the remaining bolts.

Remove the wheel.Mounting the spare wheel

Clean contact surfaces of wheel and
wheel hub.

Guide the spare wheel onto the align-
ment bolt and push it on.

Insert wheel bolts and tighten them
slightly.
Warning!
G
The jack is intended only for lifting the
vehicle briefly for wheel changes. It is not
suited for performing maintenance work
under the vehicle.

Never start the engine when the vehicle
is raised.


Never lie down under the raised vehicle.
!
Do not place wheel bolts in sand or dirt. This
could result in damage to the bolt and wheel hub
threads.
Warning!
G
Vehicles with collapsible tire:
Inflate collapsible tire only after the wheel is
properly mounted.
Inflate the collapsible tire using the electric
pump (
page 416) before
lowering the
vehicle.
!
To avoid paint damage, place wheel flat
against hub and hold it there while installing first
wheel bolt.

421 Practical hints
Battery
Disconnecting the battery
Depress parking brake firmly or move
gear selector lever to positionP.

Turn off all electrical consumers.

Remove SmartKey from starter switch.
Vehicles with KEYLESS-GO*:
Press the start/stop button until
the engine shuts off.

Open the driver’s door.

Open the trunk.

Read and observe safety instructions
and precautions (
page 420).

Remove the luggage box (
page 395).

Disconnect battery negative lead2.

Remove cover1 from the positive ter-
minal.

Disconnect the battery positive lead.
Removing the battery
Remove the screw-nuts securing the
battery.

Remove the battery bracket.

Pull out the battery ventilation tube
from the battery (depending on battery
arrangement in your vehicle model, the
battery ventilation tube is located on
the left or right side of the battery).

Take out the battery.
!
As with any other battery, disconnect the
battery if you do not intend to operate your vehi-
cle for an extended period of time to prevent bat-
tery discharge or connect an accessory battery
charge unit expressly approved by
Mercedes-Benz for your vehicle model to main-
tain the battery charge. Contact an authorized
Mercedes-Benz Center for further information.
The battery, the battery ventilation hose and the
lateral plug must always be securely installed
when the vehicle is in operation.
!
Never loosen or detach battery terminal
clamps while the engine is running or the
SmartKey is in the starter switch. Otherwise the
alternator and other electronic components
could be severely damaged.
Have the battery checked regularly by an autho-
rized Mercedes-Benz Center.
Refer to Maintenance Booklet for maintenance
intervals or contact your authorized
Mercedes-Benz Center for further information.
Warning!
G
With a disconnected battery

you will no longer be able to turn the
SmartKey in the starter switch and
pressing the KEYLESS-GO* start/stop
button on the gear selector lever will
have no effect


the gear selector lever will remain
locked in positionP