2007 MERCEDES-BENZ CL500 display

203 Control systems
COMAND navigation system (during route guidance)
COMAND navigation system (during route guidance)
Cancel route guidance
Select “Destination”
“Cancel Route
Guidance” in map view with the menu
system displayed (
page 157).
Continuing cancelled route guidance
Select “Destination”
“Continue
Route Guidance” in map view with the
menu system displayed (
page 157).
COMAND calculates the route.
Route browser
Select “Route”
“Route Browser” in
map view with the menu system dis-
played (
page 157).
The route browser appears.
1Highlighted route section
2Current vehicle position; the triangle in-
dicates the vehicle’s direction of travel
3Information about the highlighted route
section
Displaying next or previous route
section: Select “Next” or “Previous”.
Increasing or reducing size of the
map: Select; or :.
Closing route browser:
Select “Back”.
iThe route browser shows an overview of the
route. You can use the route browser to move
along the route section by section and view infor-
mation about and details of each section of the
route.
iThe information 3 about the marked route
section shows the street name and the length of
the route section. Marked route section 1 is al-
ways highlighted in white and outlined in red.

204 Control systems
COMAND navigation system (during route guidance)
Displaying route information
Select “Route”
“Route Info” in map
view with the menu system displayed
(
page 157).
The route information appears.
Example display with main destination and
stopover
1Distance to the destination
2Symbol = for stopover
3Abbreviation for province (CDN) or
state (USA)
4Town/city
5Street
6Symbol < for main destination
7Estimated driving time to the destina-
tion
8Estimated arrival time
Closing route info: Slide omp or
press back button L in the center
console (
page 82).
iCOMAND uses the time set in COMAND as
the basis for calculating the estimated arrival
time. The clock must be set correctly in
COMAND (
page 227). The calculation of the
estimated arrival time does not additionally take
into account whether Daylight Saving Time or
standard time is applicable at the destination. If
the destination is in a different time zone, arrival
time display
8 is in local time. This is indicated
by “LT” in the display.
The following data cannot be seen until the route
calculation has been completed:

Distance to destination 1

Estimated arrival time 8

Estimated remaining travel time 7
If the destination is located within a partially dig-
itized area, the following data may differ from the
facts:

Distance to destination 1

Estimated arrival time 8

Estimated remaining travel time 7

205 Control systems
COMAND navigation system (during route guidance)
Detour function
Select “Route”
“Detour” in map view
with the menu system displayed
(
page 157).
The detour function display appears.
Setting length of the blockage:
Select “More” or “Less” until the de-
sired length is set.1Blocked route section
2Current vehicle position; the triangle in-
dicates the vehicle’s direction of travel
3Information about the blocked route
section
Starting route calculation:
Select “Start”, see also (
page 181).
Deleting blockage: Select “Navi”

“Route”
“Detour”
“Delete”.
Select “Back”.
iThe detour function blocks a section of the
route ahead of you. You can set the length of the
blockage. If possible, COMAND calculates a de-
tour route.
iThe detour function may direct you to
off-road routes. See Off-road and Off-map for ad-
ditional routes and cautions (
page 200).
iBlocked route section 1 is always highlight-
ed in red/white. The information about blocked
route section 3 shows which section of the
route is blocked and the length of the blocked
section.

211 Control systems
COMAND navigation system (destination memory)
Closing message: Select “OK”.
Depending on which data is missing or
cannot be found on the digital map, you
must now either:

select a state (USA) or province (CDN)

or enter a town/city

or enter a street

or enter a house number
Selecting a state (USA) or province
(CDN): Select desired state (USA) or
province (CDN) from the list.
Entering a town: Proceed as de-
scribed for destination entry in the “En-
tering a town or city” section
(
page 168).
Entering a street: Proceed as de-
scribed for destination entry in the “En-
tering a street” section (
page 171).
Entering a house number: Proceed
as described for destination entry in
the “Entering a house number” section
(
page 175).
If all data is available and matches the
digital map data, you can save the ad-
dress.
Saving: Select “Save”.Displaying your own address
Select “Navi”
“Destination”

“From Memory”.
The destination memory list appears ei-
ther with or without the input charac-
ters. Whether the input characters
appear depends on the number of en-
tries in the destination memory.
Press n.
iIn the address book entry, the town/city
and street must be spelled in the same way as
the destination entry so that the data matches
the digital map data.
In order for the state (USA) or province (CDN) to
match the map data, you may either enter the
entire name or the abbreviation in the address
book.
Examples:

Florida or FL

Colorado or CO

Alberta or AB

Ontario or ON

215 Control systems
COMAND address book
Calling up the address book
Select “Telephone”
“Telephone”

“Address Book”.
The main address book display ap-
pears. If the address book already con-
tains entries, you will see the data of an
entry.
Illustration: address book entry
Selecting an entry in the main address
book display
Slide omp or rotate ymz until the
main area is selected.
Creating a new address book entry
Select “Telephone”
“Telephone”

“Address Book”
“New Entry”.
The input menu appears with the data
fields and the input characters.
Illustration: input menu for private data
1To switch between work and home
data ( or symbol)
2Selected data field with input mark
(cursor)
3Display of set data type – in example
display, home data is set ( symbol
and “Home” display)
4Input characters
iFor phone book entries in the mobile phone
that contain a name and a telephone number,
you will see the name and the number. If a phone
book entry in the mobile phone contains several
telephone numbers, you will see the message
“Multiple Numbers” instead of a telephone num-
ber.
iPlease observe the following when creating
a new address book entry:
You can define your own address in the destina-
tion memory in navigation mode. When defining
the address, you can transfer data already en-
tered as an address book entry.
In the address book entry, the town/city and
street must be spelled in the same way as the
destination entry so that the data matches the
digital map data.
In order for the state (province) to match the
map data, its complete name or abbreviation
may be entered.
Examples:

Florida or FL

Colorado or CO

Alberta or AB

Ontario or ON

216 Control systems
COMAND address book
Switching between private and
business data: Select symbol 1.
The display switches to private or busi-
ness data, depending on the previous
status.
Changing data field: Slide rmq re-
peatedly until desired entry is highlight-
ed.
or
Select [ or ] repeatedly until de-
sired entry is highlighted.
Entering data into a field:
Select desired characters one by one
from the input characters.
Toggling upper and lower case for
the input characters: Select& or
(.
Changing language for the input
characters: Select!.
Select desired language.
Changing character set for the input
characters: Select#.
Depending on the previous setting, you
will change to letters with special char-
acters or to numbers with special char-
acters.
Moving cursor in the data field:
SelectY or Z.
Deleting individual characters:
Select) and briefly press n.
The character to the left of the cursor is
deleted.
Deleting an entire entry: Select)
and press and hold n until the entry is
deleted.
Saving an entry: Select?.
Canceling an entry: Select “Back”.
If one of the data fields contains new
data, a prompt will appear asking
whether you want to save the entry.
Select “Yes” or “No”.
The entry will either be saved or
not, depending on your selection.

217 Control systems
COMAND address book
Deleting an entry
Search for desired entry (page 217).
Select “Options”
“Delete”.
A deletion prompt appears.
Select “Yes” or “No”.
The entry will either be deleted or not,
depending on your selection.
Searching for an address book entry
Select “Telephone”
“Telephone”

“Address Book”
“Search”.
The search menu appears with the
smart speller.
1Symbol for complete address data
from the navigation system
2Symbol for summarized entries
from the mobile phone with the same
name but different telephone numbers
3Category symbol
4Smart speller
5Symbol for voice entry
6Back to the main address book displayEntries with category symbol 3 come
from the mobile phone. The following cate-
gory symbols are possible:

= symbol for “Mobile” category

= symbol for “Home” category

= symbol for “Work” category

= symbol for “Fax” category

= symbol for “Pager” category

= symbol for “Main” category or for
unknown category or for phone entries
that are saved on the SIM card of a
GSM mobile phone
Entries without a category symbol or with
the or symbols come from the
COMAND address book. All other entries
come from the mobile phone and are only
visible when the mobile phone is in the cra-
dle*.
It is possible to add voice entries. Entries
with the symbol contain a voice entry
(
page 224).
iYou cannot delete phone book entries from
the mobile phone.

218 Control systems
COMAND address book
Entries with the symbol contain com-
plete, navigable address data from the nav-
igation system that correspond to digital
map data. It is possible to quickly start
route guidance to these types of entry
(
page 223).
Switching from the smart speller to the
list
Slide mq repeatedly or press n until
the smart speller is hidden.
or
Select ?.
Switching from the list to the smart
speller
Select “Back” from the list.Searching
Searching via the smart speller
Switch from the list to the smart speller
if necessary.
Changing smart speller language:
Select!.
Select desired language.
Changing smart speller character
set: Select#.
Depending on the previous setting, you
will change to letters with special char-
acters or to numbers with special char-
acters.
Entering characters: Select the char-
acters one by one of the entry you are
searching for.
Deleting individual characters:
Select) and briefly press n.
Each time you enter or delete a charac-
ter, the closest match will be displayed
at the top of the list.
Deleting an entire entry: Select)
and press and hold n until the entry is
deleted.
Canceling search: Switch from the
smart speller to the list (
page 218).
The entry at the top of the list is auto-
matically highlighted.
Going back to main address book
display: If necessary, switch from the
list to the smart speller (
page 218)
and select “Back” in the smart speller.
Searching via the list
If necessary, switch from the smart
speller to the list (
page 218).
Rotate ymz or slide qmr until desired
entry is highlighted on the list.