Page 334 of 406

Black plate (334,1)
NOTE
lTo replace the bulb, contact an
Authorized Mazda Dealer.
lIf the halogen bulb is accidentally
touched, it should be cleaned with
rubbing alcohol before being used.
lUse the protective cover and carton
for the replacement bulb to dispose
of the old bulb promptly and out of
the reach of children.
Brake lights/Taillights, Rear turn signal
lights, Reverse lights, Rear side-marker
lights
1. Remove the cover.
2. Turn the socket and bulb assembly
counterclockwise and remove it.3. Disconnect the bulb from the socket.
Rear side-maker light
Brake light/Taillight
Rear direction indication light
Reverse light
4. Install the new bulb in the reverse order
of removal.
NOTE
To replace the bulb, contact an
Authorized Mazda Dealer.
High-mount brake light
Due to the complexity and difficulty of
the procedure, the LED bulbs should be
replaced by an Authorized Mazda Dealer.
NOTE
LED bulb replacement is not possible.
The rear combination component must
be replaced.
License plate lights
1. Wrap a flathead screwdriver with a soft
cloth to prevent damage to the lens and
remove the lens by carefully prying on
the edge of the lens with a flathead
screwdriver.
8-38
Maintenance and Care
Owner Maintenance
CX-7_8V28-EA-06B_Edition2 Page334
Monday, March 13 2006 5:7 PM
Form No.8V28-EA-06B
Page 335 of 406
Black plate (335,1)
2. Disconnect the bulb by pulling it out.
3. Install the new bulb in the reverse order
of removal.
qReplacing Interior Light Bulbs
Overhead light/Map lights (Front)
Due to the complexity and difficulty of
the procedure, the bulbs should be
replaced by an Authorized Mazda Dealer.
Overhead light (Rear), Luggage
compartment light
1. Wrap a small flathead screwdriver with
a soft cloth to prevent damage to the
lens and remove the lens by carefully
prying on the edge of the lens with the
flathead screwdriver.
2. Disconnect the bulb by pulling it out.
3. Install the new bulb in the reverse order
of removal.
Maintenance and Care
Owner Maintenance
8-39
CX-7_8V28-EA-06B_Edition2 Page335
Monday, March 13 2006 5:7 PM
Form No.8V28-EA-06B
Page 336 of 406

Black plate (336,1)
Fuses
Your vehicle's electrical system is
protected by fuses.
If any lights, accessories, or controls don't
work, inspect the appropriate circuit
protector. If a fuse has blown, the inside
element will be melted.
If the same fuse blows again, avoid using
that system and consult an Authorized
Mazda Dealer as soon as possible.
qFuse Replacement
Replacing the fuses on the driver's side
If the electrical system doesn't work, first
inspect fuses on the driver's side.
1. Turn off the ignition switch and other
switches.
2. Open the fuse panel cover.
Fuse panel cover
3. Pull the fuse straight out with the fuse
puller provided on the inside of the
cover for the fuse panel and the fuse
block cover inside of the engine
compartment.
4. Inspect it and replace if it's blown.
NormalBlown
5. Push in a new fuse of the same
amperage rating, and make sure it fits
tightly. If it doesn't, have an Authorized
Mazda Dealer install it.
If you have no spare fuses, borrow one
of the same rating from a circuit not
essential to vehicle operation, such as
the ROOM circuit.
8-40
Maintenance and Care
Owner Maintenance
CX-7_8V28-EA-06B_Edition2 Page336
Monday, March 13 2006 5:7 PM
Form No.8V28-EA-06B
Page 337 of 406
Black plate (337,1)
WARNING
Always replace a fuse with one of the
same rating. Otherwise you may
damage the electric system.
Replacing the fuses under the hood
If the headlights or other electrical
components don't work and the fuses in
the cabin are OK, inspect the fuse block
under the hood. If a fuse is blown, it must
be replaced. Follow these steps:
1. Turn off the ignition switch and all
other switches.
2. Remove the fuse block cover.
3. Pull the fuse straight out with the fuse
puller provided on the inside of the
engine compartment fuse block cover.
4. If a fuse is blown, replace it with a new
oneof the same amperage rating.
Normal
Blown
NOTE
To replace the MAIN fuse, contact an
Authorized Mazda Dealer (page 8-42).
Maintenance and Care
Owner Maintenance
8-41
CX-7_8V28-EA-06B_Edition2 Page337
Monday, March 13 2006 5:7 PM
Form No.8V28-EA-06B
Page 338 of 406
Black plate (338,1)
qFuse Panel Description
Fuse block (Engine compartment)
DESCRIPTION FUSE RATING PROTECTED COMPONENT
1 IGN 2 40A Ignition system
2 BLOWER 40A Blower motor
3 BTN 60A For protection of various circuits
4 FAN 2 40A Cooling fan
5 IGN 1 40A Ignition system
6 FAN 1 40A Cooling fan
7 P.SEAT 40A Power seat
í
8 INJ 30A Injector
9 ROOF 20A Moonroofí
10 BOSE 30A Bose audio systemí
11 ENGINE 30A Engine control system
12 D.LOCK 20A Power door locks
13 P.WIND 30A Power windows
14 FUEL 30A Fuel pump
15 ABS 1 40A ABS
16 ABS 2 20A ABS
17 DSC 7.5A DSC
18 FOG 20A Fog lights
í
8-42
Maintenance and Care
íSome models.
Owner Maintenance
CX-7_8V28-EA-06B_Edition2 Page338
Monday, March 13 2006 5:8 PM
Form No.8V28-EA-06B
Page 339 of 406
Black plate (339,1)
DESCRIPTION FUSE RATING PROTECTED COMPONENT
19 DEF 30A Rear window defroster
20 TNS 15AParking lights, License plate lights,
Illuminated entry system
21 A/C 10A Air conditioner
í
22 ETC 20A Accelerator position sensor
23 H/L HI 15A Headlight levelingí
24 DRL 15A DRLí
25 H/L LO RH 15A Headlight low beam (RH)
26 H/L LO LH 15A Headlight low beam (LH)
27 ENG BAR 2 7.5A PCM
28 ECM 10A Engine control system
29 ENG BAR 1 15A Air flow sensor, EGR control valve
30 P.WIND 2 20A Power windows
31 STOP 10A Brake lights
32 HORN 20A Horn
33 ENG B+ 25A PCM
34 HAZARD 10A Hazard warning flashers, Turn signals
Fuse block (Driver's side)
DESCRIPTION FUSE RATING PROTECTED COMPONENT
1 OUTLET 1 15A Accessory Socket
Maintenance and Care
Owner Maintenance
8-43íSome models. CX-7_8V28-EA-06B_Edition2 Page339
Monday, March 13 2006 5:8 PM
Form No.8V28-EA-06B
Page 340 of 406
Black plate (340,1)
DESCRIPTION FUSE RATING PROTECTED COMPONENT
2 OUTLET 2 15A Accessory Socket
3 P.MIR 7.5A Power control mirror
4 WIPER 30A Windshield wiper and washer
5 M.DEF 7.5A Mirror defroster
í
6 ENG BAR 3 7.5A Air flow sensor, EGR control valve
7 P.WIND 15A Power windows
8 A/B 7.5A Advance Restraint System
9 ENGINE 15A Engine control system
10 METER 10A Instrument cluster
11 ROOM 15A Audio system, Overhead light
12 ILLUMI 10A Dashboard illumination
13 SEAT 20A Seat warmer
í
14 A/C 10A Air conditionerí
15 R.WIP 10A Rear window wiper and washer
8-44
Maintenance and Care
íSome models.
Owner Maintenance
CX-7_8V28-EA-06B_Edition2 Page340
Monday, March 13 2006 5:8 PM
Form No.8V28-EA-06B
Page 344 of 406

Black plate (344,1)
Insects, tar, tree sap, bird droppings,
industrial fallout, and similar deposits can
damage the finish if not removed
immediately. When prompt washing with
plain water is ineffective, use a mild soap
made for use on vehicles.
Thoroughly rinse off all soap with
lukewarm or cold water. Don't allow soap
to dry on the finish.
After washing the vehicle, dry it with a
clean chamois to prevent water spots from
forming.
WARNING
Driving with Wet Brakes:
Driving with wet brakes is dangerous.
Increased stopping distance or the
vehicle pulling to one side when
braking could result in a serious
accident. Light braking will indicate
whether the brakes have been affected.
Dry the brakes by driving very slowly
and applying the brakes lightly until
brake performance is normal.
Waxing
Your vehicle needs to be waxed when
water no longer beads on the finish.
Always wash and dry the vehicle before
waxing it. In addition to the vehicle body,
wax the metal trim to maintain its luster.
1. Use wax which contains no abrasives.
Waxes containing abrasive will remove
paint and could damage bright metal
parts.
2. Use a good grade of natural wax for
metallic, mica, and solid colors.3. When waxing, coat evenly with the
sponge supplied or a soft cloth.
4. Wipe off the wax with a soft cloth.
NOTE
A spot remover to remove oil, tar, and
similar materials will usually also take
off the wax. Rewax these areas even if
the rest of the vehicle doesn't need it.
qRepairing Damage to the Finish
Deep scratches or chips on the finish
should be repaired promptly. Exposed
metal quickly rusts and can lead to major
repairs.
CAUTION
If your Mazda is damaged and needs
metal parts repaired or replaced, make
sure the body shop applies anti-
corrosion materials to all parts, both
repaired and new. This will prevent
them from rusting.
qPaint Damage Touch-up
Repair damage to the finish caused by
stone chipping, damage during parking
etc., by using Mazda touch-up paint
before rust begins to form. First, remove
the dirt and grease with a clean soft cloth.
If rust has already begun to form:
1. Remove rust completely with
sandpaper.
2. Wipe with a clean soft cloth.
3. Apply rust preventive primer to the
area.
8-48
Maintenance and Care
Appearance Care
CX-7_8V28-EA-06B_Edition2 Page344
Monday, March 13 2006 5:8 PM
Form No.8V28-EA-06B