2007 LEXUS LX470 ECO mode

76
1-7. Safety information
Installing child restraints using a seat belt (child restraint lock function belt)
■Rear facing child seat Infant/convertible
Place the child seat on the second
or third outboard seat facing the
rear of the vehicle.
Run the seat belt through the child
seat and insert the plate into the
buckle. Make sure that the belt is
not twisted.
Fully extend the shoulder belt and
then allow it to retract slightly in
order to activate the ALR lock
mode.
Lock mode allows the seat belt to
retract only.
STEP1
STEP2
STEP3

100
2-1. Driving procedures
■Selecting a driving mode
The following patterns can be selec ted to suit current driving and
operating conditions.
Normal mode
Power mode
For powerful acceleration and
driving in mountainous regions.
“2nd STRT” (second start)
For starting on slippery road
surfaces, such as on snow.
Press “2nd” to return to normal
mode.

108
2-2. Instrument cluster
■Indicators
The indicators inform the driver of th e operating state of the vehi-
cle’s various systems.
Turn signal indicator
( P. 1 0 2 )Active height control indi-
cator ( P. 1 3 0 )
Headlight high beam indi-
cator (P. 112)Vehicle stability control
system OFF indicator
(P. 1 4 3 )
(U.S.A.)
Headlight indicator
( P. 112)Center differential lock
indicator ( P. 1 4 3 )
(Canada)
Tail light indicator
(P. 112)
(U.S.A.)
Active traction control
system indicator
(P. 1 4 3 )
Cruise control indicator
( P. 1 2 0 )
(Canada)
Active traction control
system indicator
( P. 1 4 3 )
Slip indicator ( P. 1 4 2 )“AIRBAG ON/OFF” indi-
cator( P. 6 7 )
Roll sensing of curtain
shield airbags off indica-
tor ( P. 6 5 )
Automatic transmission
indicator ( P. 99)
“PWR” mode indicator
( P. 1 0 0 )
Automatic transmission
second start indicator
(P. 1 0 0 )
*
*
*
**
*

110
2-2. Instrument cluster
Trip information display
Trip information■ Average vehicle speed
■ Driving distance
Displays the average vehicle speed since the engine
was started or the function was reset.
The function can be reset by pushing the “RESET”
switch for longer than on e second when the average
vehicle speed is displayed.
Displays the driving dist ance since engine was
started or the function was reset.
The function can be rest pushing the “RESET” switch for
longer than one second wh en the driving distance is
displayed.
The trip information display presents the driver with a variety of driving-
related data.
Display items can be switched
by pushing the “MODE” switch.

116
2-3. Operating the lights and windshield wipers
■Rain drop sensor
■If no windshield washer fluid sprays
Check that the washer nozzles are not blocked if there is washer fluid in the wind-
shield washer fluid reservoir.
■In extremely hot or cold weather
The system will turn off if the windshield gets extremely hot (at more than 194F
[90 C]) or cold (at less than -22 F [-30C]).
■Windshield wiper features
●The rear window and outside rear view mirror defoggers automatically turn on
when you operate the wipers.
■Customization
Settings (e.g. drip prevention function) can be changed. (P. 3 8 9 )
CAUTION
■Caution regarding the use of windshield wipers in “AUTO” mode
The windshield wipers may operate unexpect edly if the sensor is touched or the
windshield is subject to vibration in “AUTO” mode. Take care that your fingers or
anything else do not become caught in the windshield wipers.
The sensor judges the amount of raindrops.

133
2-4. Using other driving systems
2
When driving
■Extra high mode
If the vehicle becomes stuck, extra high mode may be automatically selected when
the vehicle height is in high mode with the four-wheel drive control lever in the “L”
position.
The vehicle height is raised to 2.8 in. (70 mm) higher than the normal mode height,
or slightly higher.
Extra high mode will change back to high mode when:
• The vehicle is no longer stuck
• The four-wheel drive control lever is shifted to a position other than “L”
●If you push “ ▼” when in extra high mode, normal mode is selected.
●Extra high mode cannot be manually selected.
■Turning off the active height control suspension
●The system will remain off until the switch is pushed again, even if the ignition is
turned off.
●Even if AHC is turned off, the system automatically selects the normal mode if
the vehicle's speed exceeds 19 mph (30 km/h).
■Automatic leveling function
The vehicle is adjusted to a fixed height for each mode, regardless of the number of
occupants and the luggage load.
●However the vehicle cannot be raised if the vehicle load exceeds the following
limits:
• Up to 4 occupants* plus approximately 661 lb. (300 kg) in the normal mode
• Up to 4 occupants* plus approximatel y 375 lb. (170 kg) in the high mode
*: average weight 150 lb. (68 kg) per person
●If the vehicle height cannot be raised when in the normal mode, and “LO” is lit
on the height mode indicator, the vehicle is loaded too heavily. Take extra care
when driving in this condition.
If the vehicle height cannot be raised even after unloading the vehicle, press
“ ▼ ” then “ ▲” on the height mode select switch. If the vehicle height still cannot
be raised, turn the ignition off th en on again, then try once more.

134
2-4. Using other driving systems
■If the vehicle height does not change
If the vehicle is loaded too heavily, or the undercarriage has come into contact with
the road surface, the vehicle height cannot be raised/lowered. In this case, the indi-
cator lights will change as follows:
●The current mode indicator light will turn off, and the target mode indicator light
will begin flashing.
●The target mode indicator light will turn off, and the original mode indicator light
will be lit once more. (The vehicle height does not change.)
■In the following cases AHC will not operate
●The brake pedal has been depressed for longer than 5 seconds while the vehi-
cle is stopped.
●The suspension fluid temperature is lower than -22°F (-30°C).
●Driving on bumpy roads which may cause the suspension to fully elongate.
●If the steering wheel is abruptly turned more than 3/4 of a revolution with the
center differential lock system activated.
■Cold weather operation
It may take longer for the vehicle height to change if the suspension fluid tempera-
ture drops below -5°F (-15°C).
AHC does not operate when the suspension fluid temperature drops below -22°F
(-30°C).
●In this case, the selected height mode indicator light will flash when the height
mode select switch is pressed, however the vehicle height will not change.
Once the engine has warmed the suspension fluid to within normal operating
limits, AHC will begin operating and the vehicle height will automatically
change to the selected mode.
●When the suspension fluid is around -22°F (-30°C), the vehicle height may not
be able to be raised, even if AHC is operating. In this case, push “ ▼” then “▲ ”
on the height mode select switch after further warming the engine to select the
desired vehicle height.

135
2-4. Using other driving systems
2
When driving
■Parking and stopping tips
●If you immediately stop the engine after off-road driving, or park the vehicle for
a long time, the vehicle height may gradually lower. When parking, make sure
there is nothing under the vehicle that may come in contact with the underbody.
The vehicle will return to the set height when the engine is started.
●The vehicle height may change as the temperature changes when the engine is
stopped. The vehicle will return to the set height when the engine is started.
■Propeller shaft noise
If the vehicle height is adjusted on a slop e, or with the selector lever in a position
other than “P” or “N” while the vehicle is stopped, you may hear a sound caused by
the expansion and contraction of the propel ler shaft. This does not indicate a mal-
function.
■Continued system operation
Even if the engine is stopped while the ve hicle height is being lowered, operation
will continue for up to 12 seconds.
■Active height control failure warning
●If a malfunction occurs in the AHC system, normal mode is automatically
selected.
The height control “ OFF” indicator will bl ink, and AHC cannot be activated until
the malfunction is corrected.
Stop the engine and start it again. If the height control “OFF” indicator light
turns off, the system is operating correc tly. If the indicator light continues to
blink, have the vehicle checked at your Lexus dealer as soon as possible.
●If the height control “OFF” indicator light does not come on when the ignition
switch is turned on, there is a malfunction in the AHC system. You can continue
normal driving, however have the vehicle checked by your Lexus dealer as soon
as possible.
■Installing or removing heavy equipment
If the equipment exceeds 33 lb. (15 kg), the front torsion bar must be adjusted. See
your Lexus dealer.