2007 Lancia Musa diagram

CONTROL BUTTONS
To use the information the “Multifunction display” is able to give you
should firstly familiarise with the control buttons using them as
described below.
Before doing anything you are advised to read this section thoroughly.
+ and – buttons
To scroll the menu and the related options upwards/downwards, to
increase/decrease/set the value displayed and, with side/taillights on,
to adjust the intensity of the instrument dimmer/ menus/ instrument
panel, sound system and automatic two-zone climate control system
display (if pressed with “Set-up menu on”).
MODE button
Press for less than 2 seconds (pulse) indicated with
bin the
following diagrams, to confirm the option required and/or move to
the main screen (same option) or access the Menu.
Press for more than 2 seconds indicated with
cin the following
diagrams, to exit the set-up menu during setting.
TRIP button
Press for less than 1 seconds (pulse) indicated with
hin the
following diagrams, to scroll the Trip computer screens.
Press for more than 2 seconds indicated with
iin the following
diagrams, to reset the Trip computer and start a new mission.
38
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND
CONTROLS
L0D0025m
L0D0026m

41
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND
CONTROLS
ACCESS TO MENU SCREEN
After the “Initial check”, it is possible to access the menu screen pressing the button
Q.
To surf the menu press buttons +or–.
IMPORTANT If after entering the menu no setting/adjustment is performed within 60 seconds, the system exits
the menu automatically and returns to previously displayed screen.
In this case the last selected but not confirmed setting (through button
Q) is not stored and therefore the
operation shall be repeated.
When the car is running, it is possible to access only the reduced menu (for setting “Speed limit” and “Daylight
sensor automatic headlights”).
When the car is stationary access to the whole menu is enabled.
The following diagram shows the cases described.
Q= Press “MODE” button for less than two seconds
R= Press “MODE” button for over two seconds

63
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND
CONTROLS
“Trip computer” information are displayed according to the following diagram:
See “Initial check”
and “Access to
menu screen”
Previously
displayed
screen, e.g.:(*)
%%%%
%%
continues on next page
&= “Reset General trip” and “Trip B” excluding
“Cruising range” (see paragraph “Reset
General trip”).The two screens concerning a trip
item alternate three times, then the
second one stays on fixed on the
display.
%
(*)
(*)
(*) (*) (*)
(*)
%= Press “TRIP” button for less than two seconds - &= Press “TRIP” button for over two seconds

USING THE MECHANICAL GEARBOX
To engage the gears, press the clutch pedal fully and shift the gear
lever into one of the required positions (the diagram is shown on the
knob).
IMPORTANT The car can only be put into reverse gear when it has
stopped moving completely. With the engine running, before engaging
the reverse, wait at least 2 seconds with the clutch pedal fully down to
prevent damage and grating of the gears.
To engage 6
thgear (where required), press the lever to the right to
prevent engaging 4thgear by mistake. A similar action is required to
shift down from 6th to 5th.
To engage reverse (R) from neutral, lift the sliding ring (A) under the
knob and shift the lever to the right and back (only for petrol
versions).
For Multijet versions, just shift lever to the right and back.
188
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
L0D0150m
To change gears properly you must push the clutch pedal fully down. It is therefore
essential that there is nothing under the pedals: make sure mats are lying flat and do
not get in the way of the pedals.
WARNING
Do not drive with your hand resting on the gear lever as the force exerted, even if slight, could lead
over time to premature wear on the gearbox internal components.
L0D0360m

ASSEMBLY DIAGRAM
The tow hook structure must be fastened in the
points shown by the symbolØusing a total of 4
M8 screws, 2 M10 screws and 2 M12 screws.
The hook should be fastened to the body avoiding
any type of drilling and trimming of the rear
bumpers that remains visible when the hook is
removed.
IMPORTANT It is compulsory to fasten a label
(plainly visible) of suitable size and material with
the following wording:
MAX LOAD ON BALL 60 kg
205
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
After fitting, screw holes shall be sealed to prevent exhaust gas inlet.WARNING
L0D0256m
Existing holes
Existing holes
Existing holesStandard ball
Full load

213
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
WARNING
LIGHTS AND
MESSAGES
FRONT PASSENGER AIR BAG DEACTIVATED (where fitted)
Dial warning light comes on when front passenger air bag is
deactivated. With front passenger air bag on, turning the ignition key
to MAR, warning light
Fcomes on flashing on the cluster for about
4 seconds, then it shall go off.
F
SEAT BELTS NOT FASTENED
The warning light will come on flashing, together with the warning
buzzer when, with the car moving, the driver's seat belt is not
correctly fastened. The S.B.R. (Seat Belt Reminder) buzzer can only
be excluded by Lancia Dealership, the system can be reactivated
through the set-up menu (see diagram aside).
<
amber
red
Warning
light on
dial Message on
multifunction
display
WARNINGWarning light Findicates also warning light ¬failure. This is indicated by
intermittent flashing, over 4 seconds, of warning light F. In this event, warning
light
¬could be not up to indicate restraint system failures, if any. Stop the car
and contact Lancia Dealership to have the system checked.