2007 Lancia Musa buttons

62
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND
CONTROLS
TRIP COMPUTER
The “Trip computer” displays information relating to the operating status of the car. This function comprises the
“General trip”, concerning the complete mission of the car and “Trip B”, concerning the partial car mission. The
car is delivered with “Trip B” set to “ON”. This function (as shown in the graph below) is contained within the
complete mission. Both functions are resettable. The “General trip” displays the figures relating to Cruising
Range, Travelled Distance, Average fuel consumption, Current fuel consumption, Average speed, Travel time
(driving time). “Trip B” displays information concerning Travel Distance B, Average fuel consumption B,
Average speed B, Travel time B (driving time). The “Trip B” function can be excluded.
Start of journey procedure (reset)
To start a new journey monitored by the “General Trip”, with the key to MAR, press button
{on right
steering column stalk with mode
&(see paragraph “Display control buttons”).
The reset operation in the presence of the screens concerning the “General trip” makes it possible to reset also
the “Trip B”. The reset operation in the presence of the screens concerning only the “Trip B” makes it possible
to reset only the information associated with this function.
IMPORTANT The “Cruising range” information cannot be reset.
Reset TRIP B
End of partial mission
Start of new partial mission
End of partial mission
Start of new partial mission
Reset TRIP B
End of partial mission
Start of new partial mission Reset GENERAL TRIP
End of complete mission - Start of new missionReset GENERAL TRIP
End of complete mission - Start of new mission
End of partial mission
Start of new partial mission Reset TRIP B
Reset TRIP B
TRIP B
TRIP B
TRIP B GENERAL TRIP˙
˙
˙
˙˙
˙
˙ ˙
%= Press “TRIP” button for less than two seconds - &= Press “TRIP” button for over two seconds

66
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND
CONTROLS
Cruising range= = Shows the distance in km (or
mi) that the car can still cover before needing fuel,
assuming that driving conditions are kept unvaried.
The display will show “- - - - in the following
cases:
❒value for range to empty lower than 50 km or
fuel level below 4 litres; in this event before
“- - - -” the message “Warning, limited range”
will be displayed (this message will be displayed
also if not in TRIP COMPUTER mode);
❒in case of car parked with engine running for a
long period, when the car moves off the range to
empty indication will be displayed again.
Travelled distance= shows the km (or miles)
covered from last reset (*).
Average fuel consumption= shows the average
consumption calculated from last reset (*), this
value can be expressed in l/100 km, km/l or mpg.
Instant consumption = shows the fuel
consumption variation updated every second, it can
be expressed in l/100 km or mpg. In case of car
parked with engine running the display will show
“- - - -”. When the car moves off the instant
consumption indication will be displayed again.
Average speed= shows the average speed of the
car in relation with total time elapsed from last reset
(*) and it can be expressed in km/h or in mph.Travel time= time elapsed from last reset (*).
(*) Reset can be:
– “manual”, reset is performed by the driver by
pressing the relevant button (see paragraph
“Control buttons”)
– “automatic”, reset is performed when the
travelled distance reaches 9999.9 km or when
Travel time reaches 99:59 (99 hours and 59
minutes)
– after reconnecting the battery.
IMPORTANT Lacking information, Trip computer
values are displayed with “- - - -”. When normal
operating condition is reset, calculation of different
units will restart regularly. Values displayed before
the failure will not be reset (*).
IMPORTANT After battery disconnection/
connection certain displayed values are equal to
“- - - -” until significant data for calculation are
available.

67
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND
CONTROLS
INSTRUMENT PANEL, DISPLAY AND BUTTON LIGHTING ADJUSTMENT
(LIGHT RHEOSTAT)
With this function it is possible to adjust the lighting (dimming/brightening) of the instrument cluster and two-
zone climate control display (where provided).
To adjust proceed as follows:
See “Initial check”
and “Access to
menu screen”
– +– +
Automatic return to standard screen
after few seconds or by
pressing button
Q
Previously
displayed
screen, e.g.:Use buttons +/– to carry out required
light adjustment.
L0D0040m
Q= Press “MODE” button for less than two seconds
R= Press “MODE” button for over two seconds

89
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND
CONTROLS
The system enables to set or to change the
following parameters and functions
manually:
❒air temperatures on driver/front
passenger side;
❒fan speed (continuous variation);
❒air distribution on five levels
(driver/front passenger side);
❒climate control compressor on/off
enable;
❒monozone/two-zone distribution
priority;
❒fast demisting/defrosting;
❒air recirculation;
❒rear heated window;
❒system off;
CONTROLS
A MONO function button (for aligning set
temperatures)
B climate control compressor on/off
button
C inside air recirculation on/off button
D display showing climate control system
dataE climate control system off button
F MAX-DEF function button (front window fast
defrosting/demisting)
G rear window heating on/off button
H AUTO function button (automatic mode) and knob to
adjust temperature on passenger side
I buttons for air distribution on passenger side
L button for adjusting fan speed
M button for air distribution on driver side
N AUTO function button (automatic mode) and knob to
adjust temperature on driver side
L0D0065m

90
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND
CONTROLS
SWITCHING THE CLIMATE
CONTROL SYSTEM ON
The system can be started in different ways, but it is
advisable to press one of the AUTO buttons and
then to turn the knobs to set the temperatures
required on the display.
It is possible to personalise required temperatures
(driver and passenger) with a maximum difference
of 7 °C.
This way the system will start working completely
automatically to reach the temperatures set as
quickly as possible. The system will adjust the air
temperature, flow and distribution and will control
the air recirculation function and the conditioner
compressor on/off.
During fully automatic operation, the only manual
settings required are the following:
❒MONO, to align the air temperature and
distribution set on the passenger’s side (front or
rear) with that on the driver’s side;
❒…, air recirculation, to keep it always on or
off;
❒-, to speed up demisting/defrosting of
windscreen, front side windows, rear window
and door mirrors;
❒(, to demist/defrost the rear heated window
and the door mirrors.During completely automatic system operation, the
temperatures, air distribution and the fan speed set
can be changed at any time through the relevant
buttons or knobs: the system will automatically
change its settings to adjust to the new
requirements.
During full automatic operation (FULL AUTO),
any change in air distribution and/or air flow
and/or compressor turning on and/or air
recirculation will obtain FULL disappearing. In this
way functions will be controlled manually until
pressing the AUTO button again. The fan speed is
the same for all passenger compartment areas.
With one or more functions engaged manually, the
adjustment of the temperature of the air admitted to
the passenger compartment continues to be
controlled automatically by the system, except with
the climate control compressor off. In fact, in this
condition, the air admitted to the passenger
compartment cannot have a lower temperature than
the outside air.

92
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND
CONTROLS
To switch the function off, simply turn the
temperature knob counterclockwise and set the
required temperature.
❒LO function (highest cooling power):
this is activated by turning the temperature knob
counterclockwise below the min. value (16 °C). It
can be activated independently from the driver’s or
passenger’s side or both (also selecting the MONO
function).
This function can be engaged when requiring to
cool the passenger compartment as quickly as
possible, exploiting the maximum potential of the
system. This function engages inside air
recirculation and climate control compressor, while
air distribution and fan speed are controlled
according to environmental conditions. All manual
settings are however possible with this function on.
To switch the function off, simply turn the
temperature knob clockwise and set the required
temperature.Front air distribution
selection buttons
I-M
Pressing the relevant
buttons it is possible to
manually choose one of the five possible air
distributions to the left and right side of the
passenger compartment:
▲Air flow to the windscreen and front side window
vents to demist or defrost them.
˙Air flow to dashboard central and side vents to
provide satisfactory ventilation to the chest and
face, specially during the summer.
▼Air flow towards the front and rear lower parts of
the passenger compartment. Due to the natural
tendency of heat to spread upwards, this type of
distribution allows heating of the passenger com-
partment in the shortest time, also giving a prompt
feeling of warmth to the coldest parts of the body.
˙
▼Splitting of the air flow between the vents to the
lower part of the passenger compartment
(warmest air) and the dashboard centre and side
outlets (coolest air). This air flow distribution is
particularly useful in spring and autumn, when
the sun is shining.
▲
▼Splitting of the air flow between the lower part of
the passenger compartment and the windscreen
and front side window demisting/defrosting vents.
This type of air distribution allows satisfactory
heating of the passenger compartment while pre-
venting possible misting of the windows.

93
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND
CONTROLS
Set air flow distribution is indicated by the
corresponding button led switching on.
With a combined function set, pressing a button will
turn on the main function of the button pressed,
together with the functions set yet. Pressing the
button of the active function will turn the function
off (led off).
To restore automatic air distribution control after a
manual selection, press button AUTO.
When the driver selects air distribution towards the
windscreen, also the air distribution on passenger’s
side will automatically be directed to the
windscreen. The passenger can however select a
different air distribution by pressing the relevant
buttons.Fan speed adjustment buttons L
Pressing the ends of button p
increases or decreases the fan speed
and therefore the amount of air
admitted to the passenger
compartment, although keeping the required
temperature.
The fan speed is shown by the lit bars on the
display
❒max fan speed = all bars lit
❒min fan speed = one bar lit.
The fan can be cut off only if the climate control
compressor has been switched off pressing button B.
IMPORTANT To restore automatic fan speed
control after a manual adjustment, press button
AUTO.

94
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND
CONTROLS
AUTO buttons
H-N
(automatic
operation)
Pressing the AUTO
button (on driver and/or front passenger side) the
system automatically adjusts the amount and
distribution of the air admitted to the passenger
compartment, cancelling all the previous manual
adjustments.
This condition is indicated by the message FULL
AUTO on the front system display.
Manual operation of at least one automatic function
(air recirculation, air distribution, fan speed or
climate control compressor off) will cause FULL
message going off the display. This means that
automatic control is not complete (except
temperature control which is always automatic).
IMPORTANT Should the system (after manual
settings) be no longer able to guarantee the required
temperature set in the passenger compartment, the
set temperature value will start flashing to indicate
this condition, after one minute the AUTO message
will turn off.
To restore automatic system control after one or
more manual selections, press button AUTO.MONO button A (alignment of set
temperatures and air distribution)
Pressing button MONO automatically
aligns the temperature on the front
passenger’s side with that on the
driver’s side. It is therefore possible to set the same
temperature and air distribution between the two
zones simply turning the knob on the driver’s side.
This function is provided to simplify temperature
adjustment of the whole passenger compartment
when only the driver is on board. Separate
operation of the set temperatures and air
distribution is automatically restored by turning
knob (H) or pressing button MONO (A) again when
the button led is on.
Air recirculation on/
off button C
Air recirculation is controlled
according to the following operating
logics:
❒forced switching on (air recirculation always
on), indicated by the turning on of the led on
button C and symbol íon the display;
❒forced switching off (air recirculation always off
with air inlet from the outside), indicated by the
turning off of the button led and êon the
display.