2007 Lancia Musa engine

ENGINE COOLANT TEMPERATURE GAUGE
The turning on of the warning light A indicates that the coolant fluid
temperature is too high; in this case, stop the engine and contact a
Lancia Dealership.
This shows the temperature of the engine coolant fluid and begins
working when the fluid temperature exceeds approx. 50°C.
Under normal conditions, the needle should hover around the middle
of the scale according to the working conditions.
IMPORTANT If the needle reaches the low temperature area with
warning light A on, this means that there is a failure. Contact a
Lancia Dealership.
28
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND
CONTROLS
If the needle reaches the red area, stop the engine immediately and contact a Lancia Dealership.
L0D0024m

Cruising range= shows the distance (in km or
miles) that the car can still cover before needing
fuel, assuming that driving conditions are kept
unvaried. The display will show “- - - -” in the
following cases:
❒value for range to empty lower than 50 km or
fuel level below 4 litres; in this event before “- -
- -” the message “Warning, limited range” will
be displayed (this message will be displayed also
if not in TRIP COMPUTER mode);
❒in case of car parked with engine running for a
long period, when the car moves off the range to
empty indication will be displayed again.
Travelled distance= shows the km (or miles)
covered from last reset (*).
Average fuel consumption= shows the average
consumption calculated from last reset (*), this
value can be expressed in l/100 km or mpg.
Instant consumption= shows the fuel
consumption variation updated every second, it can
be expressed in l/100 km or mpg. In case of car
parked with engine running the display will show “-
- - -”. When the car moves off the instant
consumption indication will be displayed again.
Average speed= shows the average speed of the
car in relation with total time elapsed from last reset
(*), this value can be expressed in km/h or in mph.
35
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND
CONTROLS
Travel time= time elapsed from last reset (*).
(*) Reset can be:
– “manual”, reset is performed by the driver by
pressing the relevant button (see paragraph
“Control buttons”)
– “automatic”, reset is performed when the
travelled distance reaches 3999.9 km or when
travel time reaches 99:59 (99 hours and 59
minutes)
– after reconnecting the battery.
IMPORTANT Lacking information, Trip computer
values are displayed with “- - - -”. When restoring
normal operating conditions after a failure,
calculation will restart regularly without resetting
values.
IMPORTANT After battery
disconnection/connection certain displayed values
are equal to “- - - -” until significant data for
calculation are available.

40
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND
CONTROLS
INITIAL CHECK
Turning the ignition key to MAR, the multifunction display shows the message “Checking”: the diagnostic
phase of all the electronic systems on the car has started. This lasts few seconds: if no faults are detected, when
the engine has started, the display shows the “Check OK” message.
See section “Warning lights and messages” if faults are found.
Is the
engine
started?YES
If no failures are
present
The “Service schedule” includes vehicle maintenance every 20,000 km (or 12,000 mi) or every year; this is shown automatically,
with the ignition key at MAR, starting from 2,000 km (or 1,240 mi) or 30 days from this deadline and it is shown again every 200
km (or 124 mi) or 3 days. For 1.3 Multijet versions, see “Care and Maintenance” in section “Service schedule to change engine oil
and filter and air cleaner. When a programmed maintenance interval (coupon) is near to come, turning the ignition key to MAR, will
display the message “Service” followed by the number of km, or days to go before car servicing. “Scheduled servicing” message is
displayed in km, miles or days according to the approaching service interval. Contact a Lancia Dealership to carry out any service
operation provided by the “Service schedule” or “Annual inspection plan”, and to reset the display.
If the display shows a failure
message, see details in section
“Warning lights and messages”.
Standard
screen display or
NO

60
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND
CONTROLS
The “Service schedule” includes vehicle maintenance every 20,000 km (or 12,000 mi) or every year; this is shown automatically,
with the ignition key at MAR, starting from 2,000 km (or 1,240 miles) or 30 days from this deadline and it is shown again every
200 km (or 124 mi) or 3 days. For 1.3 Multijet versions, see “Care and Maintenance” in section “Service schedule” to change engine
oil and filter and air cleaner. When a programmed maintenance interval (coupon) is near to come, turning the ignition key to MAR,
will display the message “Service” followed by the number of km or days to go before car servicing. “Service” message is displayed
in km or mi or days according to the approaching service interval. Contact Lancia Dealership to carry out any service operation
provided by the “Service schedule” or “Annual inspection plan” and to reset the display.
Return to menu
screen Return to
previously
displayed
screen, e.g.:
continued from
previous page
R
Q
Q= Press “MODE” button for less than two seconds
R= Press “MODE” button for over two seconds

66
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND
CONTROLS
Cruising range= = Shows the distance in km (or
mi) that the car can still cover before needing fuel,
assuming that driving conditions are kept unvaried.
The display will show “- - - - in the following
cases:
❒value for range to empty lower than 50 km or
fuel level below 4 litres; in this event before
“- - - -” the message “Warning, limited range”
will be displayed (this message will be displayed
also if not in TRIP COMPUTER mode);
❒in case of car parked with engine running for a
long period, when the car moves off the range to
empty indication will be displayed again.
Travelled distance= shows the km (or miles)
covered from last reset (*).
Average fuel consumption= shows the average
consumption calculated from last reset (*), this
value can be expressed in l/100 km, km/l or mpg.
Instant consumption = shows the fuel
consumption variation updated every second, it can
be expressed in l/100 km or mpg. In case of car
parked with engine running the display will show
“- - - -”. When the car moves off the instant
consumption indication will be displayed again.
Average speed= shows the average speed of the
car in relation with total time elapsed from last reset
(*) and it can be expressed in km/h or in mph.Travel time= time elapsed from last reset (*).
(*) Reset can be:
– “manual”, reset is performed by the driver by
pressing the relevant button (see paragraph
“Control buttons”)
– “automatic”, reset is performed when the
travelled distance reaches 9999.9 km or when
Travel time reaches 99:59 (99 hours and 59
minutes)
– after reconnecting the battery.
IMPORTANT Lacking information, Trip computer
values are displayed with “- - - -”. When normal
operating condition is reset, calculation of different
units will restart regularly. Values displayed before
the failure will not be reset (*).
IMPORTANT After battery disconnection/
connection certain displayed values are equal to
“- - - -” until significant data for calculation are
available.

69
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND
CONTROLS
WARNING
Any adjustment of the steering wheel position must be carried out only with the
car stationary and the engine turned off.
STEERING WHEEL ADJUSTMENT
The steering wheel can be adjusted both in height A and axially B.
Proceed as follows:
❒release the lever pulling it towards the steering wheel (position 2);
❒adjust the steering wheel as required;
❒lock the lever pushing it forwards (position 1).
L0D0055m
WARNING
It is absolutely forbidden to carry out whatever after-market operation involving
steering system or steering column modifications (e.g.: installation of anti-theft
device) that could badly affect performance and safety, cause the lapse of
warranty and result in car non-compliance with the regulations in force.

96
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND
CONTROLS
Climate control compressor on/off
button B
Press the
√button, when the button
led is on, to switch the compressor
off. The led will go off. By pressing
again the button when the led is off, the system
automatic control of the compressor activation is
restored; this condition is indicated by button led
lighting up.
When the air conditioner compressor is off, the
system deactivates air recirculation to prevent
window misting up. Although the system is still able
to maintain the required temperature, the message
FULL on the display will go off. If the system is no
longer able to keep the required temperature, also
the message AUTO will turn off.
IMPORTANT Air at a temperature lower than that
of the outside air cannot be let into the passenger
compartment when the compressor is off.
Furthermore, in particular environmental
conditions, the windows could mist up fast because
the air is no longer dehumidified.Setting will be stored also when the engine is
stopped.
Either press again button √(in this case the system
operates as heater only) or AUTO to reset automatic
control of the compressor.
With compressor off, if the outside temperature is
higher than the set temperature, the system cannot
reach the required temperature. This will be
signalled by the flashing of set temperature value on
the display for a few seconds, then the message
AUTO will go off.
When the compressor is off, it is possible to reset
manually the fan speed (no bar displayed).
When the compressor is on and the engine is
running, fan speed cannot be lower than the
minimum (one bar displayed).

97
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND
CONTROLS
Button for fast windscreen and
front side window
demisting/defrosting F
Press this button: the climate control
system will automatically switch on
all the functions required for fast windscreen and
front side window demisting/defrosting, that is:
❒climate control system compressor on (with
proper climatic conditions);
❒air recirculation off;
❒maximum air temperature HI on both areas;
❒fan speed according to engine coolant
temperature in order to limit letting cold air into
the passenger compartment for demisting the
windows;
❒air flow directed to the windscreen and front side
window vents;
❒heated rear windowIMPORTANT The fast windscreen
demisting/defrosting function stays on for approx.
3 minutes after the engine coolant temperature
exceeds 50°C (petrol versions) or 35°C
(Multijet versions).
When the max. demisting/defrosting function is on,
the led on the relevant button and that on the
heated rear window button turn on. Message FULL
AUTO on the display will turn off.
When the max. demisting/defrosting function is on,
the only manual operations possible are manual
adjustment of the fan and switching rear window
heating off.
Press button F or air recirculation button C or
compressor button B or AUTO buttons N o H to
reset the previous system operation conditions.