2007 ISUZU KB P190 ECO mode

5C-26 BRAKES

A bleeding operation is necessary to remove air from the
hydraulic brake system whenever air is introduced into the
hydraulic system. It may be necessary to bleed the hydraulic
system at all four brakes if air has been introduced through a
low fluid level or by disconnecting brake pipes at the maste
r
cylinder. If a brake pipe is disconnected at one wheel, only that
wheel cylinder/caliper needs to be bled. If the pipes are
disconnected at any fitting located between the master cylinde
r
and brakes, then the brake system served by the disconnected
pipe must be bled.

1. Set the parking brake completely, then start the engine.
NOTE:
The vacuum booster will be damaged if the bleeding operation
is performed with the engine off.
2. Remove the master cylinder reservoir cap.


RTW 75CSH001701
3. Fill the master cylinder reservoir with brake fluid. Keep the
reservoir at least half full during the air bleeding operation.
4. Always use new brake fluid for replenishment.
5. In replenishing brake fluid, take care that air bubbles do not enter the brake fluid.

W hen the master cylinder is replaced or overhauled, first
bleed the air from the master cylinder, then from each
wheel cylinder and caliper following the procedures
described below.



RTW 75CSH001801
Bleeding the Master Cylinder
6. Disconnect the rear wheel brake pipe (1) from the master
cylinder.
Check the fluid level and replenish as necessary. I
f
replenished, leave the system for at least one minute.
7. Depress the brake pedal slowly once and hold it depressed.
8. Completely seal the delivery port of the master cylinder with your finger, where the pipe was disconnected, then release
the brake pedal slowly.
9. Release your finger from the delivery port when the brake pedal returns completely.
10. Repeat steps 7 through 9 until the brake fluid comes out o
f
the delivery port during step 7.
NOTE: Do not allow the fluid level in the reservoir to go belo
w
the half-way mark.
11. Reconnect the brake pipe (1) to the master cylinder and tighten the pipe.
12. Depress the brake pedal slowly once and hold it depressed.
13. Loosen the rear wheel brake pipe (1) at the master cylinder.
14. Retighten the brake pipe, then release the brake pedal slowly.

BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

5C-28 BRAKES

27. After the bleeding operation is completed on each individual
wheel, check the level of the brake fluid in the reservoir and
replenish up to the “MAX" level as necessary.
28. Attach the reservoir cap.
29. Stop the engine.




05007-1

BRAKE LINE (HOSES AND PIPES)
• Inspect all hoses and pipes for wear, bending, chafing,
cracks, dents, or any other damage.
Make necessary correction or replace parts if these abnormal conditions are found through inspection.
• All hoses, pipes and joints can be damaged easily.
Do not allow the hose to become excessively twisted and bent when working with them, and pay special attention to
all the brake lines not to damage them when repairing o
r
replacing other parts (axle, suspension, etc).
• Inspection for leakage should be performed by depressing
the brake pedal fully.
If leakage is apparent at the circumference of joints, retighten or replace these parts.
This procedure must be performed whenever brake lines are installed.
• After disconnecting the hoses and pipes, cap or tape the
openings to prevent entry of foreign material.



BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

5C-54 BRAKES
DISASSEMBLY




RTW 75CMF000701

Disassembly Steps
1. Cap
2. Diaphragm
3. Filter
4. Pin
5. Reservoir tank
6. Grommet
▲ 7. Front seal


8. Guide assembly
▲ 9. Snap ring
▲ 10. Stopper bolt and gasket
▲ 11. Primary piston
▲ 12. Secondary piston
13. Cylinder body


Note:
• Be sure to replace the designated with new ones.
• W ash the disassembled parts in clean brake fluid.
• Use compressed air to clean the ports.
• Do not allow dirt and dust to contaminate the disassembled
parts.



BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

BRAKES 5C-55
Important Operations
W hen disassembling, inspecting or reassembling the master
cylinder assembly, take care not to bring the parts into contact
with mineral oil or dust. W ash the piston cups only with brake
fluid. Do not use gasoline or other mineral-base cleaning
solvents.



7. Front Seal
Front seal remain in the vacuum booster side, when removing
master cylinder.
9. Snap Ring
Remove the snap ring from the cylinder body with pushing in
the primary and secondary pistons.
10. Stopper Bolt and Gasket
Remove the stopper bolt from the cylinder body with pushing in
the primary and secondary pistons.


RTW 75CSH002201

11. Primary Piston
12. Secondary Piston
Don’t remove the spring from the piston.



BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

BRAKES 5C-57
REASSEMBLY



RTW 75CMF000801

Reassembly Steps
▲ 1. Secondary piston
▲ 2. Primary piston
▲ 3. Guide assembly
▲ 4. Cylinder body
▲ 5. Stopper bolt and gasket
▲ 6. Snap ring
▲ 7. Grommet


▲
8. Reservoir tank
▲ 9. Pin
▲ 10. Filter
▲ 11. Diaphragm
▲ 12. Cap
▲ 13. Front seal



1. Secondary Piston
Lubricate the piston cups on the secondary piston assemblies
with brake fluid.
Note:
Be sure to use a new piston.


BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

5C-58 BRAKES




RTW 75CSH002301






























2. Primary Piston
Lubricate the piston cup on the primary piston assemblies with
brake fluid (1).
Note:
Be sure to use a new piston.
3. Guide Assembly
Lubricate the O-ring of guide assembly with brake fluid (2) and
the cup of guide assembly with rubber grease (3) (0.2 ~ 0.3g).



RTW 75CSH002001

4. Cylinder Body
Install the secondary piston and the primary piston to the
cylinder body.
Note:
The secondary piston long hole and the cylinder body stoppe
r
bolt hole must be aligned at installation.










5. Stopper Bolt and Gasket
Install the stopper bolt to the cylinder body (the piston long hole
must be aligned with the cylinder body installation hole).
Tighten the bolts to the specified torque.

Torque N ⋅m (kgf ⋅m/lb ⋅in)
2 - 3 (0.2 - 0.3 / 17 - 26)




6. Snap Ring
Press down on the primary piston and install the snap ring to
the cylinder body groove.
Note:
Be sure to use new snap ring.


7. Grommet
1. Install the grommets to the reservoir tank.
Note:
Be sure to use are new grommets.
2. Install the reservoir tank to the cylinder body.

8. Reservoir Tank
9. Pin


BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

6 – 14 TROUBLESHOOTING
10-5 Excessive turbocharger noise
The vibration noise (the air aspiration noise) occurred when turbocharger rotates, it is normal condition of the
turbocharger, no necessary any actions.
Step Action Value(s) Yes No
1 Was the excessive noise coming from the turbocharger? —

Go to Step 2 Go to Step 10
2 Inspect the fixing bolts and bands.
Was any problem found? —
Tighten the
loose parts Go to Step 3
3 Was the intake or exhaust system gasket damaged? — Replace the
damaged gasket. Go to Step 4
4 Inspect rotation parts condition.
Was the turbine wheel rotation rough? —
Replace the
turbocharger. Go to Step 5
5 Inspect the turbine wheel.
Was the turbine wheel rubbing against housing? —
Replace the
turbocharger. Go to Step 6
6 Was the turbine wheel damaged? — Replace the
turbocharger. Go to Step 7
7 Were there carbon deposits in the turbine or
compressor housing? —
Clean or
replace the
turbocharger. Go to Step 8
8 Inspect the oil supply condition.
Was the oil feed pipe clogged? —
Repair or
replace the oil feed pipe. Go to Step 9
9 Was the turbine shaft bearing worn? — Replace the
turbocharger. Go to Step 10
10 Are any DTC stored? — Go to indicated
DTC Solved

11. Rotating Part Wear of Turbocharger
Step Action Value(s) Yes No
1 Inspect engine oil.
Was it contaminated with foreign materials? —
Replace the
engine oil Go to Step 2
2 Was the recommended engine oil grade/viscosity
being used? API CD or
ISUZU
genuine/ 10W –30
Go to Step 3 Replace the
engine oil
3 Was the oil feed pipe restricted? — Clean or
replace the oil feed pipe Go to Step 4
4 Was the oil seal of turbocharger defective? — Replace the oil
seal Go to Step 5
5 Was the center housing oil drain passage clogged? — Clean center
housing or
replace the
turbocharger Go to Step 6
6 Was there oil sludge and/or coking on the turbine
shaft? —
Replace the
turbocharger Go to Step 7
7 Are any DTC stored? — Go to indicated
DTC Solved


BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

SECTION 6A
ENGINE MECHANICAL


TABLE OF CONTENTS
PAGE
4 8
Standard Bolts ........................................................................................................... 6A - 8
Special Parts Fixing Nuts and Bolts ........................................................................ 6A - 9
Recommended Liquid Gasket ...................................................................................... 6A - 22
LOCTITE Application Procedure .................................................................................. 6A - 23
Servicing ...................................................................................................................... .. 6A - 24
Model Identification ................................................................................................... 6A - 24
Air Cleaner .................................................................................................................. 6 A - 24
Lubricating System.................................................................................................... 6A - 24
Fuel System ................................................................................................................ 6A - 25
Cooling System .......................................................................................................... 6A - 2 7
Valve Clearance Adjustment ..................................................................................... 6A - 31
Compression Pressure Measurement ..................................................................... 6A - 32
General Description ...................................................................................................... 6A- 3 6
Removal and Installation .............................................................................................. 6A- 37 Removal ...................................................................................................................... 6 A- 37
Installation .................................................................................................................. 6A- 40
Coolant Replenishment ......................................................................................... 6A- 41
Engine Warm-Up .................................................................................................... 6A- 41
Engine Repair Kit........................................................................................................... 6A - 42
Engine Overhaul ............................................................................................................ 6A- 43
Removal ...................................................................................................................... 6 A- 43
External Parts ......................................................................................................... 6A- 43
E N GINE MECHA NICA L 6A – 1
Main Dat a and Specif ications ....................................................................................... 6A -
Torque Specif ications ................................................................................................... 6A -

BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007