2007 ISUZU KB P190 check oil

4B-54 REAR AXLE
3) Axle Case to Inside Brake Drum Leakage

Checkpoint Trouble Cause Countermeasure

Replace the oil sealW orn or defective oil seal
NGOil seal



BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

4C1-16 FRONT WHEEL DRIVE
6. Using snap ring pliers, remove the snap ring (1) fastening
the ball retainer to the center shaft.
7. Remove ball retainer, ball guide and bellows.


8. Use a hammer and chisel to remove the 3 pawls (above
the large and small boot bands on the UJ side).
CAUTION :
Take care not to damage the bellows during band removal.



9. Remove band (1).
10. Remove bellows.
11. Remove dust seal from UJ.
12. Remove UJ shaft assembly.
13. Remove the mounting bracket fixing bolts, and then remove DOJ case assembly from the axle case.
14. Remove snap ring and bearing.
15. Remove snap ring and oil seal.
16. Remove bracket.


Inspection and Repair
Make necessary correction or parts replacement if wear,
damage, corrosion or any other abnormal condition are found
through inspection.
Check the following parts.
1. Drive shaft joint assembly
2. DOJ case, ball, ball guide, ball retainer
3. Bellows
4. Bearing
5. Dust seal, oil seal


BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

FRONT WHEEL DRIVE 4C1-25
Inspection and Repair
Make all necessary adjustments, repairs, and part replacements if wear, damage, or other problems are discovered
during inspection.


• Ring gear, pinion gear
• Bearing
• Side gear, pinion gear, cross pin
• Differential cage, carrier
• Thrust washer
• Oil seal


Visual Check
Inspect the following parts for wear, damage, or other
abnormal conditions.



Ring Gear Replacement
(1) The ring gear should always be replaced with the drive pinion as a set.
(2) W hen installing the ring gear, apply LOCTITE 271 o
r
equivalent to the threaded hole and bolt.
(3) Tighten the fixing bolts in a diagonal sequence as illustrated.
(4) Discard used bolts and install new ones.
Bolt Torque N⋅m (kgf ⋅m/lb ⋅ft)
108 ± 9.8 (11 ± 1/79.6 ± 7.2)




Clearance Between the Differential Pinion
and the Cross Pin
mm(in)
Standard Limit
0.05 - 0.10 (0.002 - 0.004) 0.2 (0.008)



Clearance Between the Side Gear and the
Differential Box
mm(in)
Standard Limit
0.03 - 0.10 (0.001 - 0.004) 0.15 (0.006)

BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

FRONT WHEEL DRIVE 4C1-41
Inspection and Repair
Make necessary correction or parts replacement if wear, damage or any other abnormal conditions are found
through inspection.
For inspection and servicing of disc caliper, and relative parts, and ABS parts, refer to section 5 Brakes.



• Hub
• Hub bearing
• Bearing outer race
• Disc
• Oil seal
• Knuckle spindle
• ABS sensor rotor
• Caliper



Visual Check
Check the following parts for wear, damage or other abnormal
conditions.



BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

4C1-44 FRONT WHEEL DRIVE



(2) Install the outer and inner bearing into the hub with fingers.




(3) Install oil seal using special tools.
Discard the used oil seal and install a new one.
Installer : 5-8840-2853-0
Grip : 5-8840-0007-0



Hub cap Hub

6. Hub and Disc Assembly
12. Hub Cap
Apply grease in the hub and hub cap.
Description Amount g(oz)
Hub 50 (1.77)
Hub cap 20 (0.71)
Outer bearing 6.5 (0.23)
Inner bearing 12 (0.42)




9. Hub nut
Adjustment of front wheel hub bearing preload
1. Tighten spindle nut to 29 N ⋅m (3.0 kgf·m/22 lb ⋅ft) torque.
2. Turn the hub 2-3 turns and loosen the nut just enough so that it can be turned with the fingers.
3. Turn the nut all the way in with the fingers and check to be sure the hub has no free play.
4. Measure the bearing preload by pulling one of the wheel hub studs with a spring scale.
5. Tighten the spindle nut until specified bearing preload Is obtained.
6. Install the split pin in the nut retainer.
Discard the used split pin and install a new one.
After reassembling, install the disc brake caliper assembly.
Bearing Preload N (kgf/lb)
New bearing and New oil seal 9.3 - 13.3
(0.95 - 1.36 / 2.09 – 3.00)
Reuse bearing and New oil seal 9.3 - 13.3
(0.95 - 1.36 / 2.09 – 3.00)

BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

4C1-48 FRONT WHEEL DRIVE
Inspection and Repair
Make necessary correction or parts replacement if wear, damage or any other abnormal conditions are found
through inspection.
For inspection and servicing of disc caliper, and relative parts, and ABS parts, refer to Section Brakes.



• Hub
• Hub bearing, oil seal
• Knuckle spindle
• Disc
• Caliper
• ABS sensor rotor
• Cap, Hub flange (4×4 model only),
Shim (4×4 model only), Snap ring (4×4
model only)


Visual Check
Check the following parts for wear, damage or other abnormal
conditions.




BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

4C1-56 FRONT WHEEL DRIVE
INSPECTION AND REPAIR
Make necessary correction or parts replacement if wear, damage or any other abnormal conditions are found
through inspection.
For inspection and servicing of disc caliper, and relative parts, and ABS parts, refer to Section Brakes.



• Hub
• Hub bearing, oil seal
• Knuckle spindle
• Disc
• Caliper
• ABS sensor rotor
• Cap, Hub flange, Shim, Snap ring
• Free wheeling hub parts (Option)
• Clutch, Knob, follower, inner, ring and
spring


Visual Check
Check the following parts for wear, damage or other abnormal
conditions.



BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

FRONT WHEEL DRIVE 4C1-63
TROUBLESHOOTING
Refer to this Section to quickly diagnose and repair front axle problems. Each troubleshooting chart has three
headings arranged from left to right.
(1 ) Checkpoint (2) Trouble Cause (3) Countermeasure
This Section is divided into ten sub-sections:

4 × 2 Model
1. W anders and pulls
2. Front wheel shimmy

4 × 4 Model
1. Oil leak at front axle
2. Oil leak at pinion shaft
3. Noises in front axle drive shaft joint
4. Noises in front axle
5. W anders and pulls
6. Front wheel shimmy

Propeller shaft
1 . Noise
2. Vibration


BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007