2007 ISUZU KB P190 service

1-38 HEATER AND AIR CONDITIONING
8) Charge the system to the specified amount and then close the low-pressure hand valve.
Refrigerant Amount g(lbs)
4JA1-T, 4JH1-TC, C24SE 720 (1.59)
4JJ1-TC (Standard Output)
4JJ1-TC (High Output)
4JK1-TC (High Output)
650 (1.43)

9) Check for refrigerant leaks by using a HFC-134a leak detector.
• A fully charged system is indicated by the sight glass on
the receiver/drier being free of any bubbles (Refer to
"Reading Sight Glass").
• Check the high and low pressure value of the manifold
gauge. (Refer to “CHECKING REFRIGERANT SYSTEM
W ITH MAINFOLD GAUGE” in SERVICE
INFORMATION.)
Immediately after charging refrigerant, both high and low
pressures are slightly high and to the left of the gauge, but they
settle down to the guide pressure valves as shown below:
• Ambient temperature; 30 ∼35 °C (86 ∼95 °F)
• Guide pressure
High-pressure side;
Approx. 1373 ∼1670 kPa (14 ∼17 kg/cm
2 / 199 ∼242 psi)
Low-pressure side;
Approx. 127 ∼245 kPa (1.3 ∼2.5 kg/cm
2 / 18 ∼36 psi)
10) Close the low pressure hand valve and charge valve of the refrigerant container.
11) Stop the air conditioning and the engine.
12) Disconnect the high and low pressure hoses from the manifold gauge fittings.





BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

HEATER AND AIR CONDITIONING 1-51

GENERAL REPAIR PROCEDURE
OIL SPECIFICATION
•
The HFC-134a system requires a synthetic (PAG)
compressor oil.
• Compressor (PAG) oil varies according to compressor
model. Be sure to use oil specified for the model of
compressor.
Specified Compressor Oil
DH-PR



HANDLING OF OIL
•
The oil should be free from moisture, dust, metal powder,
etc.
• Do not mix with other oil.
• The water content in the oil increases when exposed to the
air. After use, seal oil from air immediately.
• The compressor oil must be stored in steel containers, not
in plastic containers.

COMPRESSOR OIL CHECK
The Oil used to lubricate the compressor is circulating with the
refrigerant.
W henever replacing any component of the system or a large
amount of gas leakage occurs, add oil to maintain the original
amount of. oil.

Oil Capacity
Capacity total in
system CR-14 180 cm
3 (5.07 lmp fl oz)
Compressor
(Service parts)
charging amount
CR-14
180 cm3 (5.07 lmp fl oz)



BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

HEATER AND AIR CONDITIONING 1-53
Checking and Adjusting for Compressor
Replacement
180 cm3 (5.07 lmp fl oz) of oil is charged in compressor
(service parts). So it is necessary to drain the proper amount
of oil from the new compressor.
1) Perform oil return operation.
2) Discharge refrigerant and remove the compressor.
3) Drain the compressor oil and measure the extracted oil.
4) Check the compressor oil for contamination.
5) Adjust oil level as required.
Amount of oil drained
From used compressor Draining amount of oil
From new compressor
less than
90 cm
3 (2.53 lmp fl oz) Some as drained
amount
more than
90 cm
3 (2.53 lmp fl oz) 90 cm
3 (2.53 lmp fl oz)

6) Evacuate, charge and perform oil return operation.
7) Check system operation.


CONTAMINATION OF COMPRESSOR OIL
Unlike engine oil, no cleaning agent is added to the
compressor oil. Even is the compressor runs for a long period
of time (approximately 1 season), the oil never becomes
contaminated as long as there is nothing wrong with the
compressor or its method of use.
Inspect the extracted oil for any of the following
conditions:
• The capacity of the oil has increased.
• The oil has changed color to red.
• Foreign substances, metal powder, etc., are present in the
oil.
If any of these conditions exists, compressor oil is
contaminated. Whenever contaminated compressor oil is
discovered, the receiver/drier must be replaced.


BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

HEATER AND AIR CONDITIONING 1-119
SPECIAL SERVICE TOOL
ILLUSTRATION PART NO. PART NAME


5-8840-0629-0 (J-39500-A)




5-8840-0630-0
(J-39500-220A)




5-8840-0631-0
(J-39500-220ANZ)


5-8840-4056-0 (J-37872)

Drive plate holder


5-8840-0121-0 (J-33943)

Clutch pulley puller pilot

5-8840-0111-0 (J-8433)

Clutch pulley puller


5-8840-0118-0 (J-33940)

Clutch pulley installer


5-8840-0007-0 (J-8092)

Driver handle



BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

SHEET METAL 2B-1
SECTION 2B
SHEET METAL

This section includes items of front end sheet metal that are attached by bolts, screws or clips and related
accessory components.
Anticorrosion materials have been applied to the interior surfaces of some metal panels to provide rust resistance.
W hen servicing these panels, areas on which this material has been disturbed, should be properly recoated with
service-type anticorrosion material.
TABLE OF CONTENTS
PAGE
Engine Hood Assembly (A type) ...................................................................................... 2B- 2
Engine Hood Assembly (B type) ..................................................................................... 2B- 8
Engine Hood Lock (A type) .............................................................................................. 2B- 11
Engine Hood Lock (B type) .............................................................................................. 2B- 13
Front Fender Panel (A type) ............................................................................................. 2B- 15
Front Fender Panel (B type) ............................................................................................. 2B- 18
Radiator Grille (A type) ..................................................................................................... 2 B- 21
Radiator Grille (B type) .................................................................................................... 2B - 22
Rear Body...................................................................................................................... ..... 2B- 23
Body Mounting .................................................................................................................. 2B- 26
Body Dimensions .............................................................................................................. 2B - 32


BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

2B-32 SHEET METAL
BODY DIMENSIONS
Service Precaution


RUW 52BSH003301









Note : Be sure to measure from the center of one hole to the
center of the other hole.









BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

3B-2 POWER-ASSISTED STEERING SYSTEM

PAGE
Power Steering Pump (4JJ1-TC, 4JK1-TC) .................................................................... 3B – 22 Power Steering Pump and Associated Parts............................................................ 3B – 22
Removal ....................................................................................................................... 3B – 22
Installation ................................................................................................................... 3B – 22
Power Steering Pump Disassembled View .............................................................. 3B – 23
Disassembly ................................................................................................................ 3B – 24
Inspection and Repair................................................................................................. 3B – 24
Reassembly ................................................................................................................. 3B – 25
Main Data and Specifications .................................................................................... 3B – 25
Supplemental Restraint System Steering Wheel & Column ........................................ 3B – 27 Service Precaution ...................................................................................................... 3B – 2 7
SRS Connectors .......................................................................................................... 3B – 2 7
Inflator Module ................................................................................................................ . 3B – 28
Inflator Module and Associated Parts ....................................................................... 3B – 28
Removal ....................................................................................................................... 3B – 29
Inspection and Repair (with SRS air bag) ................................................................. 3B – 31
Installation ................................................................................................................... 3B – 31
Steering Wheel................................................................................................................. 3B – 33
Steering Wheel and Associated Parts ....................................................................... 3B – 33
Removal ....................................................................................................................... 3B – 33
Installation ................................................................................................................... 3B – 36
The adjustment method in case a mark has not been applied .................................... 3B – 38
Combination Switch ........................................................................................................ 3B – 39
Combination Switch and Associated Parts .............................................................. 3B – 39
Removal ....................................................................................................................... 3B – 39
Installation ................................................................................................................... 3B – 42
Lock Cylinder .................................................................................................................. . 3B – 45
Lock Cylinder and Associated Parts ......................................................................... 3B – 45
Removal ....................................................................................................................... 3B – 45
Installation ................................................................................................................... 3B – 48
System Inspection (with SRS air bag) ....................................................................... 3B – 50

BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

3B-8 POWER-ASSISTED STEERING SYSTEM
6. Fully close the shutoff valve. Record the highest
pressures.
・ If the pressure recorded is within 9800-10300 kPa
(100-105 kg/cm
2/1422-1493psi), the pump is
functioning within its specifications.
・ If the pressure recorded is higher than 10300 kPa
(105 kg/cm
2/1493psi), the valve in the pump is
defective.
・ If the pressure recorded is lower than 9800 kPa
(100 kg/cm
2/1422psi), the valve or the rotating
assembly in the pump is defective.
7. If the pump pressures are within specifications, leave the valve open and turn (or have someone
else turn) the steering wheel fully in both directions.
Record the highest pressures and compare with the
maximum pump pressure recorded in step 6. If this
pressure cannot be built up at either side of the
power steering unit, the power steering unit is
leaking internally and must be replaced.
8. Shut the engine off, remove the testing gauge.
9. Reconnect the pressure hose, check the fluid level and make the needed repairs.
10. If the problem still exists, the steering and front suspension must be thoroughly examined.

Maintenance
The hydraulic system should be kept clean, the fluid
level in the reservoir should be checked at regula
r
intervals and fluid added when required. Refer to
Recommended Fluids and Lubricants in General
Information section for the type of fluid to be used and
the intervals for filling.
If the system contains some dirt, flush it as described in
this section. If it is exceptionally dirty, the pump must be
completely disassembled before further usage. (The
steering unit cannot be disassembled.)
All tubes, hoses, and fittings should be inspected for
leakage at regular intervals. Fittings must be tight. Make
sure the clips, clamps and supporting tubes and hoses
are in place and properly secured.
Power steering hoses and lines must not be twisted,
kinked or tightly bent. Air in the system will cause
spongy action and noisy operation. W hen a hose is
disconnected or when fluid is lost, for any reason, the
system must be bled after refilling. Refer to Bleeding the
Power Steering System in this section.
・ Inspect gear for looseness or damage.
・ Inspect hoses to insure they are not touching an
y
other parts of the vehicle.
・ Inspect fluid level and fill to the proper level.

Fluid Level
1. Run the engine until the power steering fluid
reaches normal operating temperature, about 55 °
C (130 °F), then shut the engine off.
2. Check the level of fluid in the reservoir.
3. If the fluid level is low, add power steering fluid as
specified in General Information to the proper level
and install the receiver cap.
4. W hen checking the fluid level after the steering system has been serviced, air must be bled from
the system. Refer to Bleeding the Power Steering
System in this section.

Bleeding the Power Steering System
W hen a power steering pump or unit has been installed,
or an oil line has been disconnected, the air that has
entered the system must be bled out before the vehicle
is operated. If air is allowed to remain in the powe
r
steering fluid system, noisy and unsatisfactory operation
of the system may result.

Bleeding Procedure
W hen bleeding the system, and any time fluid is added
to the power steering system, be sure to use only powe
r
steering fluid as specified in General Information.
1. Fill the pump fluid reservoir to the proper level and let the fluid settle for at least two minutes.
2. Start the engine and let it run for a few seconds. Do not turn the steering wheel. Then turn the engine
off.
3. Add fluid if necessary.
4. Repeat the above procedure until the fluid level remains constant after running the engine.
5. Raise and support the front end of the vehicle so that the wheels are off the ground.
6. Start the engine. Slowly turn the steering wheel right and left, lightly contacting the wheel stops.
7. Add power steering fluid if necessary.
8. Lower the vehicle, set the steering wheel at the straight forward position after turning it to its full
steer positions 2 or 3 times, and stop the engine.
9. Check the fluid level and refill as required.
10. If the fluid is extremely foamy, allow the vehicle to settle for a few minutes, then repeat the above
procedure.

Flushing the Power Steering System
1. Raise and support the front end of the vehicle off
the ground until the wheels are free to turn.
2. Remove the fluid return line at the pump inlet connector and plug the connector port on the pump.
Direct the line toward a large container to catch the
draining fluid.
3. W hile running the engine at idle, fill the reservoi
r
with new power steering fluid. Turn the steering
wheel in both directions. Do not contact or hold the
steering wheel to the wheel stops. This will cause
the pump to go to pressure relief mode, which ma
y
cause a sudden fluid overflow at the reservoir.


BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007