2007 ISUZU KB P190 mirror

ELECTRICAL-BODY AND CHASSIS 8A-617


No. Connector face No. Connector face
D1



Brown
Power window motor-driver side D10



White

Power window switch-passenger side
D2


White
Remote mirror-driver side D11



BrownPower window motor rear-LH
D3


Black
Front speaker-driver side D12



White

Power window switch rear-LH
D4


Black
Door lock actuator-driver side D13



BlackRear speaker-LH
D5


White
Power window switch-driver side D14



BlackDoor lock actuator rear-LH
D6


Brown
Power window motor-passenger side D15



BrownPower window motor rear-RH
D7


White
Remote mirror-passenger side D16



WhitePower window switch-RH
D8


Black
Speaker-passenger side D17



BlackRear speaker-RH
D9



Black
Door lock actuator-passenger side (keyless & antitheft) D18




BlackDoor lock actuator rear-RH
D9


Black
Door lock actuator-passenger side D19



WhiteRemote mirror switch-driver side

BACK TO CHAPTER INDEX TO MODEL INDEXISUZU KB P190 2007

8A-618 ELECTRICAL-BODY AND CHASSIS


No. Connector face No. Connector face
D20



White
Power window switch-driver side D30



White

Door mirror-turn signal light-passenger side
D21


White
Tweeter-driver side

D22



White
Tweeter-passenger side

D23



White
Door lock & super actuator front (RH)

D24



White
Key cylinder switch-driver side

D25



White
Door lock actuator-passenger side

D26



White
Key cylinder switch-driver side

D27



White
Door lock & super lock actuator RR (RH)

D28



White
Door lock & super lock actuator RR (LH)

D29



White
Door mirror-turn signal light-driver side



BACK TO CHAPTER INDEX
TO MODEL INDEXISUZU KB P190 2007

10-2 CAB
WINDSHIELD
REMOVAL AND INSTALLATION





This illustration is based on RHD model

RTW 7A0LF001201

Removal Steps
1. Interior trim panels (Front side) /Headlining/Instrument panel assembly
2. W iper arm assembly
▲ 3. Room mirror
4. Side molding
5. Vent cowl cover
6. W indshield stopper
7. Upper molding
▲ 8. W indshield
9. Engine hood rear seal
Installation Steps
▲
9. Engine hood rear seal
▲ 8. W indshield
7. Upper molding
6. W indshield stopper
5. Vent cowl cover
4. Side molding
3. Room mirror
▲ 2. W iper arm assembly
1. Interior trim panels (Front side) /Headlining/Instrument panel assembly

BACK TO CHAPTER INDEX TO MODEL INDEX
ISUZU KB P190 2007

CAB 10-3



RUW 5A0SH002901

Important Operations - Removal
3. Room Mirror
Remove the screw and pull the room mirror to the upper side.

8. Windshield
Remove the windshield, carefully following the steps listed
below:
1) Use a knife to cut through part of the adhesive caulking material.
2) Secure one end of a piece of steel piano wire (0.02 inches in diameter) to a piece of wood that can serve as a handle.
3) Use a pair of needle nose pliers to insert the other end o
f
the piano wire through the adhesive caulking material at the
edge of the windshield.
4) Secure the other end of the piano wire to another piece o
f
wood.





5) W ith the aid of an assistant, carefully move the piano wire
with a sawing motion to cut through the adhesive caulking
material around the entire circumference of the windshield.
6) Lift the windshield from the body.
7) Clean any remaining adhesive caulking material from the area of the body which holds the windshield.
8) Use a soft rag and unleaded gasoline to wipe off an
y
adhesive remaining on the windshield.



Important Operations - Installation
9. Engine Hood Rear Seal
Install the engine hood rear seal as shown in the illustration.
1 : Seal
2 : Clip
3 : Rear (windshield side)
4 : Front


BACK TO CHAPTER INDEX TO MODEL INDEX
ISUZU KB P190 2007

CAB 10-11
DISASSEMBLY




This illustration is based on RHD model

RTW 4A0LF000701
Disassembly Steps
▲ 1 . Switch bezel/W indow regulator handle
▲ 2. Power window switch
▲ 3. Bezel
▲ 4. Door mirror cover
▲ 5. Door trim panel
▲ 6. Tweeter (Required Option)
▲ 7. Door mirror assembly
▲ 8. Outer waste seal
▲ 9. Bracket
▲ 10. Speaker assembly
▲ 11 . W aterproof sheet
▲ 12. Inside lever
▲ 13. W indow glass
▲ 14. W indow regulator/Power window
regulator

▲
15. Glass run
▲ 16. Glass run rear channel / Glass ran rear
channel with Door lock control or Anti
theft (European Countries)
▲ 17. Door lock assembly/Door lock assembly
with super lock
▲ 18. Outside handle protector (EUROPE)
▲ 19. Outside handle
▲ 20. Door lock cylinder protector (EUROPE)
▲ 21. Door lock cylinder / Door lock cylinder
with door lock switch (European
Countries)
22. Door harness assembly
23. Anti rattler


BACK TO CHAPTER INDEX TO MODEL INDEX
ISUZU KB P190 2007

10-12 CAB

RUW 5A0SH002201

Important Operations
1. Switch Bezel/Window Regulator Handle
• Remove the 2 screws and disconnect the connectors.



•
To remove the regulator handle, remove the clip at the
root of the handle by using wire.



2. Power Window Switch
• Remove the 2 screws.



RUW 5A0SH00230 1

3. Bezel
• Remove the screw.


4. Door Mirror Cover
• Pull out the upper clip, and then take out the cove
r
upward.



5. Door Trim Panel
• Pull out the trim panel at the 8 clip positions (Powe
r
window type).


BACK TO CHAPTER INDEX TO MODEL INDEX
ISUZU KB P190 2007

CAB 10-13


• Remove the 2 screws and pull out the trim panel at the 8
clip positions (W indow regulator handle type).
RTW 3A0SH00070 1

6. Tweeter (Required option)
• Disconnect the tweeter harness connector and remove
the 3 screws.


7. Door Mirror Assembly
• Remove 3 fixing bolts and then remove the connector.
8. Outer Waste Seal


9. Bracket
10. Speaker Assembly • Remove the fixing screw and then remove the
connector.
11. Waterproof Sheet • Take care not to damage the sheet when peeling it off.
12. Inside Lever • Disconnect the door lock cables.

BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

CAB 10-15
REASSEMBLY




This illustration is based on RHD model

RTW 4A0LF000801

Reassembly Steps
1. Anti rattler
2. Door harness assembly
▲ 3. Door lock cylinder / Door lock cylinder
with door lock switch (European
Countries)
▲ 4. Door lock cylinder protector (EUROPE)
▲ 5. Outside handle
▲ 6. Outside handle protector (EUROPE)
7. Door lock assembly / Door lock assembly with super lock
8. Glass run rear channel / Glass ran rear channel with Door lock control or Anti
theft (European Countries)
9. Glass run
10. W indow regulator / Power window regulator
▲ 11. W indow glass
12. Inside lever
13. W aterproof sheet
14. Speaker assembly
15. Bracket
16. Outer waste seal
17. Door mirror assembly
18. Tweeter (Required option)
19. Door trim panel
20. Door mirror cover
21. Bezel
22. Power window switch
▲ 23. Switch bezel / W indow regulator handle

BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007