2007 ISUZU KB P190 torque

5D-4 PARKING BRAKE SYSTEM
Installation
1. Install switch (5).
Torque: 1.5 N ⋅
⋅⋅
⋅
m (0.15 kgf ⋅
⋅⋅
⋅
m/13 lb ⋅
⋅⋅
⋅
in)
2. Set parking lever assembly.
3. Install bolts (4) and nut (1) and tighten them to the specified torque.
Torque: 15 N ⋅
⋅⋅
⋅
m (1.5 kgf ⋅
⋅⋅
⋅
m/11 lb ⋅
⋅⋅
⋅
ft)
4. Set front parking brake cable in parking leve
r
assembly.
5. Drive clip into the outer cable groove of front parking brake cable at the outside of parking leve
r
assembly.
6. Drive adjust nut (3) on the front end of front parking brake cable so that front ends of rea
r
parking brake fit into the rear end (equalizer) of
front cable.
7. Install instrument panel assembly & cross beam.
Refer to section 10.
8. Install bolts (2)(6) and tighten them to the specified torque.
Torque: 15 N ⋅
⋅⋅
⋅
m (1.5 kgf ⋅
⋅⋅
⋅
m/11 lb ⋅
⋅⋅
⋅
ft)
9. Install all parts removed.
Refer to section 10.
10. W hen the parking brake cable is replaced, pull the parking brake lever with a force equivalent to
operating force: 490 N (50 kg/110 lb), 10 times fo
r
conditioning.
11. Adjust nut (3) so that the lever goes through 8 −14
notches, when pulled with an operation force o
f
294 N (30 kg/66 lb) and check brake for no drag.





RTW 65BSH000101



BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

5D-6 PARKING BRAKE SYSTEM




This illustration is based on the RHD model

RTW 35DMF000101

Legend
(1) Adjust Nut
(2) Clip
(3) Bolt

(4) Bolt
(5) Parking Brake Cable T-end
(6) Front Parking Brake Cable


Removal
1. Remove seat assembly and seat adjuster.
Refer to section 10.
2. Turn over the carpet so that front parking brake cable appears.
3. Remove adjust nut.
4. Pull out clip and take out front parking brake cable.
5. Remove bolt.
6. Disconnect parking brake cable T-ends from front parking brake cable.
7. Take out front parking brake cable through the floor hole.
Installation

1. Apply grease (multipurpose type grease) to the
connecting portion of parking brake cable T-end
and front parking brake equalizer (arrow mark).
2. Let rear end (equalizer) of front parking brake cable enter the floor hole and connect it with
parking brake rear cable T-end.
3. Set front parking brake cable in the parking leve
r
assembly.
4. Drive clip into the outer cable groove of front parking brake cable at the outside of the parking
lever assembly.
5. Install bolt on the floor and tighten to the specified torque.
Torque: 15 N ⋅
⋅⋅
⋅
m (1.5 kgf ⋅
⋅⋅
⋅
m/11 lb ⋅
⋅⋅
⋅
ft)


BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

5D-8 PARKING BRAKE SYSTEM
Parking Brake Lever
Parking Brake Lever Assembly and Associated Parts (Bucket Seat)



RTW 35DSF000101

Legend
(1) Rear Floor Console
(2) Parking Brake Cable T-end
(3) Adjust Nut

(4) Switch
(5) Parking Brake Lever Assembly
(6) Bolt
(7) Equalizer


Removal
1. Remove rear floor console.
Refer to section 10.
2. Loosen adjust nut.
3. Remove bolt.
4. Remove switch.
5. Disconnect parking brake cable T-end from parking brake lever assembly.
6. Take out parking brake lever assembly.

Installation
1. Apply grease (multipurpose type grease) to the
connecting portion of parking brake rear cable
T-end and parking brake lever equalizer. (arrow
mark).
2. Connect parking brake rear cable T-end to equalizer.
3. Install switch.

4. Tighten the parking brake lever fixing bolt to the
specified torque.
Torque: 15 N ⋅
⋅⋅
⋅
m (1.5 kgf ⋅
⋅⋅
⋅
m/11 lb ⋅
⋅⋅
⋅
ft)
5. Drive adjust nut on parking brake assembly so that parking brake cable T-end fits into equalizer.
6. Install rear floor console.
Refer to section 10.
7. Pull parking brake lever with a force equivalent to operating force: 490 N (50 kg/110 lb), 10 times fo
r
conditioning.
8. Adjust nut so that parking brake lever goes through 6 −9 notches, when pulled with an
operation force of 294 N (30 kg/66 lb).
9. Check brake for no drag.


BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

5D-10 PARKING BRAKE SYSTEM
Removal
1. Remove wheel and tire.
2. Remove brake drum.
3. Remove tension pin and shoe clamp spring.
4. Remove return spring.
5. Remove shoe assembly with parking brake lever.
6. Remove shoe assembly with adjuster lever and spring.
7. Remove parking brake inner cable from parking brake lever.
8. Use offset box wrench (12 mm hex.) to compress locking lugs on the cable, then remove parking
brake outer cable from back plate.
NOTE: Do not twist or bend the cable too much.
A damaged cable will cause poor operation or a cable
break down.




RTW 55CSH000301

Legend
(1) Offset Box W rench (12 mm hex)
9. Remove nut to fix the cable on the leaf spring.
10. Take out parking brake rear cable from the back plate.
11. Remove parking brake cable bolt and nut.
12. Disconnect T-end from the equalizer of front cable.

Installation

NOTE: Be sure to use a new shoe clamp spring and a
new adjuster lever clip.
1. Apply grease (multipurpose type grease) to the connecting portion of the rear cable and equalizer.
(arrow mark).
2. Install parking brake outer cable in back plate and inner cable in parking brake lever.
3. Install return spring.
4. Install shoe clamp spring and tension pin.
5. Install shoe assembly with adjuster lever, shoe assembly with parking brake lever and spring. ----
snap action
6. Install nut and tighten it to the specified torque. Torque: 7 N ⋅
⋅⋅
⋅
m (0.7 kgf ⋅
⋅⋅
⋅
m/61 lb ⋅
⋅⋅
⋅
in)
7. Connect T-end with equalizer through outer cable retainer.
8. Install parking brake cable nut and tighten it to the specified torque.
Torque: 15 N ⋅
⋅⋅
⋅
m (1.5 kgf ⋅
⋅⋅
⋅
m/11 lb ⋅
⋅⋅
⋅
ft)
9. Install parking brake cable bolt and tighten it to the specified torque.
Torque: 7 N ⋅
⋅⋅
⋅
m (0.7 kgf ⋅
⋅⋅
⋅
m/61 lb ⋅
⋅⋅
⋅
in)
10. Install brake drum.
11. Install wheel and tire.
12. Pull parking brake lever with a force equivalent to operating force: 490 N (50 kg/110 lb), 10 times fo
r
conditioning.
13.
Adjust parking brake lever adjusting nut so that
parking brake lever goes through 6-9 notches
(Bucket Seat) or 8 −14 notches (Bench Seat), when
pulled with an operation force of 294 N (30 kg/
66 lb).
14. Check brake for no drag.


BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

PARKING BRAKE SYSTEM 5D-13
Torque Specifications
N⋅
⋅⋅
⋅
m (kgf ⋅
⋅⋅
⋅
m/lb ⋅
⋅⋅
⋅
ft)

This illustration is based on the RHD model
RTW 35DSF000201

N⋅
⋅⋅
⋅
m (kgf ⋅
⋅⋅
⋅
m/lb ⋅
⋅⋅
⋅
ft)



E05R300006



BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

SECTION 6A
ENGINE MECHANICAL


TABLE OF CONTENTS
PAGE
4 8
Standard Bolts ........................................................................................................... 6A - 8
Special Parts Fixing Nuts and Bolts ........................................................................ 6A - 9
Recommended Liquid Gasket ...................................................................................... 6A - 22
LOCTITE Application Procedure .................................................................................. 6A - 23
Servicing ...................................................................................................................... .. 6A - 24
Model Identification ................................................................................................... 6A - 24
Air Cleaner .................................................................................................................. 6 A - 24
Lubricating System.................................................................................................... 6A - 24
Fuel System ................................................................................................................ 6A - 25
Cooling System .......................................................................................................... 6A - 2 7
Valve Clearance Adjustment ..................................................................................... 6A - 31
Compression Pressure Measurement ..................................................................... 6A - 32
General Description ...................................................................................................... 6A- 3 6
Removal and Installation .............................................................................................. 6A- 37 Removal ...................................................................................................................... 6 A- 37
Installation .................................................................................................................. 6A- 40
Coolant Replenishment ......................................................................................... 6A- 41
Engine Warm-Up .................................................................................................... 6A- 41
Engine Repair Kit........................................................................................................... 6A - 42
Engine Overhaul ............................................................................................................ 6A- 43
Removal ...................................................................................................................... 6 A- 43
External Parts ......................................................................................................... 6A- 43
E N GINE MECHA NICA L 6A – 1
Main Dat a and Specif ications ....................................................................................... 6A -
Torque Specif ications ................................................................................................... 6A -

BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

6A – 8 ENGINE MECHANICAL

TORQUE SPECIFICATION
STANDARD BOLTS
The torque values given in the following table should be applied whenever a particular torque is not specified.
N·m (kg·m/lb·ft)
8.8
4.8 (4T) (7T)
Refined Non-Refined 9.8 (9T) Strength
Class
Bolt
Identification


Bolt
Diameter ×
Pitch (mm)
M 6 ×
××
×
1.0

M 8 ×
××
×
1.25

M 10 ×
××
×
1.25

M 12 ×
××
×
1.25

M 14 ×
××
×
1.5

M 16 ×
××
×
1.5

M 18 ×
××
×
1.5

M 20 ×
××
×
1.5

M 22 ×
××
×
1.5

M 24 ×
××
×
2.0

* M 10 ×
××
×
1.5

* M 12 ×
××
×
1.5

* M 14 ×
××
×
2.0

* M 16 ×
××
×
2.0
5.88 ± 1.96
(0.60 ± 0.20/4.33 ± 1.44)
12.74 ± 4.90
(1.30 ± 0.50/9.40 ± 3.62)
27.44 ± 6.86
(2.80 ± 0.70/20.25 ± 5.06)
61.25 ± 12.25
(6.25 ± 1.25/45.21 ± 9.04)
95.55 ± 19.11
(9.75 ±1.95/70.52 ± 14.10)
130.34 ± 26.46
(13.30 ± 2.70/96.20 ± 19.53)
188.16 ± 37.24
(19.20 ± 3.80/138.87 ± 27.49)
257.74 ± 51.94
(26.30 ± 5.30/190.23 ± 38.33)
332.22 ± 81.34
(33.90 ± 8.30/245.20 ± 60.03)
448.84 ± 90.16
(45.80 ± 9.20/331.27 ± 66.54)
26.46 ± 6.86
(2.70 ± 0.70/19.53 ± 5.06)
56.84 ± 11.76
(5.80 ± 1.20/41.95 ± 8.68)
89.18 ± 17.64
(9.10 ± 1.80/65.82 ± 13.02)
124.46 ± 24.50
(12.70 ± 2.50/91.86 ± 18.08) 7.35 ± 2.45
(0.75 ± 0.25/5.43 ± 1.80)
17.15 ± 5.39
(1.75 ± 0.55/12.66 ± 4.00)
36.75 ± 9.31
(3.75 ± 0.95/27.12 ± 6.87)
75.95 ± 15.19
(7.75 ± 1.55/56.06 ± 11.21)
116.13 ± 23.03
(11.85 ± 2.35/85.71 ± 17.00)
169.54 ± 34.30
(17.30 ± 3.50/125.13 ± 25.32)
244.02 ± 49.00
(24.90 ± 5.00/180.10 ± 36.17)
337.12 ± 67.62
(34.40 ± 6.90/248.82 ± 49.41)
453.25 ± 90.65
(46.25 ± 9.25/334.53 ± 66.91)
570.36 ± 140.14
(58.20 ± 14.30/420.96 ± 103.43)
36.26 ± 8.82
(3.70 ± 0.90/26.76 ± 6.50)
70.56 ± 13.72
(7.20 ± 1.40/52.08 ± 10.13)
109.76 ± 21.56
(11.20 ± 2.20/81.01 ± 15.91)
161.70 ± 32.34
(16.50 ± 3.30/119.34 ± 23.87) -

23.52 ± 6.86
(2.40 ± 0.70/17.36 ± 5.06)
49.98 ± 12.74
(5.10 ± 1.30/36.89 ± 9.40)
94.57 ± 19.11
(9.65 ± 1.95/69.80 ± 14.10)
142.10 ± 28.42
(14.50 ± 2.90/104.88 ± 21.00)
199.92 ± 40.18
(20.40 ± 4.10/147.55 ± 29.66)
287.14 ± 57.82
(29.30 ± 5.90/211.93 ± 42.67)
395.92 ± 79.38
(40.40 ± 8.10/292.21 ± 58.59)
530.18 ± 105.84
(54.10 ± 10.80/391.30 ± 78.12)
691.88 ± 138.18
(70.60 ± 14.10/510.65 ± 101.99)
48.02 ± 11.76
(4.90 ± 1.20/35.44 ±8.68)
89.18 ± 17.64
(9.10 ± 1.80/65.82 ± 13.02)
133.28 ± 26.46
(13.60 ± 2.70/98.37 ± 19.53)
191.10 ± 38.22
(19.50 ± 3.90/141.04 ± 28.21)
An asterisk (*) indicates that the bolts are used for female threaded parts that are made of soft materials
such as casting. Those shown in parentheses in the strength class indicate the classification by the old
standard.
FLARE NUTS N·m (kg·m/lb·ft)
Pipe diameter mm
(in) Torque Pipe diameter mm
(in) Torque
4.76 (0.187)
6.35 (0.250)
8.00 (0.315) 15.2 ± 2.45(1.55 ±0.25/11.2 ± 1.8)
26.48 ± 2.94(2.70 ± 0.30/19.5 ± 2.1)
44.14 ± 4.90(4.50 ± 0.50/32.5 ± 3.6) 10.00 (0.394)
12.00 (0.472)
15.00 (0.591) 53.95 ± 4.90(5.50 ± 0.5 /39.7 ± 3.6)
88.29 ± 9.80(9.00 ± 1.0/65.0 ± 7.2)
105.45 ± 12.26(10.75 ± 1.25/77.7 ± 9.0)

BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

ENGINE MECHANICAL 6A – 23

LOCTITE APPLICATION PROCEDURE
LOCTITE Type LOCTITE Color Application Steps
LOCTITE 242 Blue
LOCTITE 262 Red
LOCTITE 270 Green
LOCTITE 271 Red 1. Completely remove all lubricant and moisture from the bolts and the
female threaded surfaces of the parts to be joined.
The surfaces must be perfectly dry.
2. Apply LOCTITE to the bolts.

3. Tighten the bolts to the specified torque.
4. W ait at least one hour before continuing the installation procedure.

LOCTITE 515 Violet 1. Completely remove lubricant and moisture from the connecting
surfaces.
The surfaces must be perfectly dry.
2. Apply a 2.0 – 2.5 mm bead of LOCTITE to one of the connecting surfaces.
There must be no gaps in the bead.
3. Tighten the bolts to the specified torque.
4. Let the joined parts set for at least thirty minutes.


BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007