2007 ISUZU KB P190 trans

MAINTENANCE AND LUBRICATION 0B-13
RECOMMENDED FLUIDS AND LUBRICANTS (For EUROPE)


In order to obtain maximum performance and longest service life from your ISUZU vehicles, it is very important to
select and use correctly the best lubricants and diesel fuels.
W hen lubricating, be sure to use ISUZU genuine lubricants or recommended lubricants listed below, according to
the maintenance schedule for each vehicle model.

LUBRICATION/FLUID GRADE
API ACEA OTHER
Diesel engine crankcase B2/B3
E2/E3
Manual transmission
Transfer case B2/B3
E2/E3
Differential
Shift on the fly system
(GL-5 only)
GL-5

BESCO GEAR OIL SH (80W-90, 90, 140) (ISUZU GENUINE)
BESCO SHIFT ON THE FLY (75W-90) (ISUZU GENUINE)
THURBAN GL-5 EP (80W-90, 85W-140) (CALTEX)
SPIRAX A (140) (SHELL)
TRANSELF TYPE B (80W-90, 85W-140) (ELF)
TRANSMISSION TM (80W-90, 85W-140) (TOTAL)
EPX90 (90)(CASTROL)
DYNA DRIVE (80W-90) (CASTROL)
ENERGEAR HYPO (90) (BP)
ENERGEAR EP (80W-90) (BP)
Differential
(Limited Slip Differential)
(GL-5 only) GL-5

BESCO GEAR OIL LSD (140) (ISUZU GENUINE)
GEAR OIL LSD (90) (CALTEX)
SPIRAX A LS 90 (90) (SHELL)
TRANSELF TYPE BLS (90) (ELF)
TRANSMISSION DA (85W-90) (TOTAL)
HYPOY LSX (90) (CASTROL)
ENERGEAR LS-M (90) (BP)
Automatic transmission MOBIL ATF 3309
Power steering

DEXRON III
Propeller shaft sliding yoke
Universal joint
(General purpose grease in
Molybdenum) NLGI #2 or #3
multi purpose type grease
containing molybdenum disulfide
Engine cooling system Good quality ethylene glycol antifreeze or GM spec.
6033-M or equivalent

NOTE:
* If GL-5 Limited Slip Differential Lubricant is not available, use GL-5 Lubricant mixed with 1 bottle (118ml) of Limited
Slip Differential Lubricant additive (Parts No. 8-01052-358-0) or equivalent.



FLUID TYPE

Clutch and brake fluid reservoir Besco brake fluid (For light duty)
Hydraulic brake fluid SAE J1703
FMVSS 116 DOT.3 grade


DIESEL FUEL/APPLICABLE STANDARD
JIS (JAPANESE INDUSTRIAL STANDARD)
DIN (DEUTSCHE INDUSTRIE NORMEN)
SAE (SOCIETY OF AUTOMOTIVE ENGINEERS)
BS (BRITISH STANDARD) Based on K2204 GAS OIL
Based on EN590: 1997L
Based on SAE J-313C
Based on BS EN590: 1997

NOTE:
Use the applicable standard or equivalent for diesel fuels.



BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

0B-16 MAINTENANCE AND LUBRICATION

OIL VISCOSITY CHART FOR TRANSMISSION CASE


OIL VISCOSITY CHART FOR FRONT AXLE AND REAR AXLE




BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

HEATER AND AIR CONDITIONING 1-33
RECOVERY, RECYCLING, EVACUATION
AND CHARGING
Handling Refrigerant-134a (HFC-134a)
Air conditioning systems contain HFC-134a.
This is a chemical mixture, which requires special handling
procedures to avoid personal injury.
• Always wear safety goggles and protective gloves.
• Always work in a well-ventilated area. Do not weld or steam
clean on or near any vehicle-installed air conditioning lines
or components.
• If HFC-134a should come in contact with any part of the
body, flush the exposed area with cold water and
immediately seek medical help.
• If it is necessary to transport or carry any container of HFC-
134a in a vehicle, do not carry it in the passenger
compartment.
• If it is necessary to fill a small HFC-134a container from a
large one, never fill the container completely. Space should
always be allowed above the liquid for expansion.
• Keep HFC-134a containers stored below 40 °C (104 °F).


WARNING
•
••
•
SHOULD HFC-134a CONTACT YOUR EYE(S), CONSULT
A DOCTOR IMMEDIATELY.
•
••
•
DO NOT RUB THE AFFECTED EYE(S). INSTEAD,
SPLASH QUANTITIES OF FRESH COLD WATER OVER
THE AFFECTED AREA TO GRADUALLY RAISE THE
TEMPERATURE OF THE REFRIGERANT ABOVE THE
FREEZING POINT.
•
••
•
OBTAIN PROPER MEDICAL TREATMENT AS SOON AS
POSSIBLE. SHOULD THE HFC-134a TOUCH THE SKIN,
THE INJURY MUST BE TREATED THE SAME AS SKIN
WHICH HAS BEEN FROSTBITTEN OR FROZEN.

F06R300012


REFRIGERANT RECOVERY
The refrigerant must be discharged and recovered by using
ACR4 (HFC-134a Refrigerant Recovery/Recycling/Recharging/
System) or equivalent before removing or installing air
conditioning parts.
ACR
4 (115V 60Hz) :5-8840-0629-0 (J-39500-A)
ACR4 (220-240V 50/60Hz)
: 5-8840-0630-0 (J-39500-220A)
ACR
4 (220-240V 50/60Hz Australian model)
: 5-8840-0631-0 (J-39500-220ANZ)
1) Connect the high and low charging hoses of the ACR
4 (or
equivalent) as shown.
2) Recover the refrigerant by following the ACR
4
Manufacturer's Instructions.
3) W hen a part is removed, put a cap or a plug on the connecting portion so that dust, dirt or moisture cannot get
into it.

BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

HEATER AND AIR CONDITIONING 1-39
Reading Sight Glass

High and low
pressure pipe
temperature The high pressure
pipe is hot and the
low pressure pipe
is cold. There is a
distinct difference
in temperature
between them. The high pressure
pipe is warm and
the low pressure
pipe is cool. There
is no great
difference in
temperature
between them. There is little
difference in
temperature
between the high
pressure pipe and
the low pressure
pipe. The high pressure
pipe is hot and the
low pressure pipe
is slightly warm.
There is a
difference in
temperature
between them.
Sight glass
condition Almost transparent.
A flow of bubbles
can be seen, but
they disappear
when the throttle is
opened.

A flow of bubbles
always can be
seen. It appears
sometimes
transparent, and
sometimes frothy.
Something like fog
faintly can be seen.
Even at idle with
the fan at "HI" (with
the window fully
open), the bubbles
cannot be seen.



Air conditioning
cycle condition
OK NG
(Not enough refrigerant) NG
(Almost no
refrigerant) NG
(Too much
refrigerant)

The sight glass provides accurate diagnosis only under the following conditions.
If the vehicle can be tested under these conditions, check the sight glass appearance and compare to the chart.
* Engine speed Idling
* A/C switch "ON"
* Blower fan operating at highest speed
* Air source selector lever at "RECIRC"
* Temperature control knob at coldest position
* Ambient temperature below 35 °C (95 °F) and humidity below 70% (See NOTE 1)
* High side pressure less than 1470 kPa (15 kg/cm
2 / 213 psi) (See NOTE 2)

NOTE 1
If the vehicle cannot be moved to a testing location that meets these specifications, then the sight glass cannot be
used for diagnosis. You must discharge and recover the refrigerant, then recharge the system with the specified
amount of refrigerant. Then continue checking the system performance.

NOTE 2
If the high side pressure is greater than stated, the sight glass cannot be used for diagnosis. You must discharge
and recover the refrigerant, then recharge the system with the specified amount of refrigerant. Then continue
checking system performance.



BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

PROPELLER SHAFT 4A-3
MAIN DATA AND SPECIFICATIONS
REAR PROPELLER SHAFT


4×2 Model 4×4 Model
Engine Model 4JJ1 (Standard Output), 4JK1 (Standard Output) 4JJ1 (Standard Output) 4JK1 (Standard Output)
Transmission Type
5M/T (MUA) A/T 5M/T
(MUA) A/T 5M/T
(MUA)
W heel Base Long ← ← ← ←
Front Suspension High Ride
Suspension Except
High Ride
Suspension High Ride
Suspension Except
High Ride
Suspension 


Rear Axle φ220mm ← ← ← ← ← ←
Type OBS ← ← ← ← ← ←
Outside Diameter mm 68.9 68.9 63.5 63.5 68.9 75 68.9
(in) (2.71) (2.71) (2.50) (2.50) (2.71) (2.95) (2.71)
Inside Diameter mm 64.9 64.9 60.3 60.3 64.9 71.8 64.9
(in) (2.56) (2.56) (2.37) (2.37) (2.56) (2.83) (2.56)
Length 1st(L1) mm 798.5 801.5 720.5 716.5 472.5 1204 472.5
(in) (31.44) (31.56) (28.37) (28.21) (18.60) (47.40) (18.60)
2nd(L2) mm 801 796 801 796 801  801
(in) (31.54) (31.34) (31.54) (31.34) (31.54)  (31.54)
Spline Major mm 29.89 29.89 29.89 29.89 29.89 29.89 29.89
Diameter (in) (1.18) (1.18) (1.18) (1.18) (1.18) (1.18) (1.18)
Fix Bolt Size M10 M10 M10 M10 M10 M10 M10
* OBS - Outboard Slip (Spline Engagement to T/M)


4×2 Model 4×4 Model
Engine Model 4JJ1 (High Output)
Transmission Type 5M/T (MUX) A/T 5M/T (MUX) A/T
W heel Base Long Long Ext. Long Long Long Long Ext. Long Long
Front Suspension High Ride
Suspension Except High
Ride
Suspension Except High
Ride
Suspension High Ride
Suspension High Ride
Suspension High Ride
25up
Suspension High Ride
Suspension High Ride
Suspension
Rear Axle φ220mm ← ← ← ← ← ← ←
Type OBS ← ← ← ← ← ← ←
Outside Diameter mm 68.9 68.9 68.9 75 68.9 68.9 68.9 75
(in) (2.71) (2.71) (2.71) (2.95) (2.71) (2.71) (2.71) (2.95)
Inside Diameter mm 64.9 64.9 64.9 71.8 64.9 64.9 64.9 71.8
(in) (2.56) (2.56) (2.56) (2.83) (2.56) (2.56) (2.56) (2.83)
Length 1st(L1) mm 777.5 777.5 925.5 706.5 434.5 438.5 584.5 1204
(in) (30.61) (30.61) (36.44) (27.81) (17.11) (17.26) (23.01) (47.40)
2nd(L2) mm 801 796 796 801 801 801 801 
(in) (31.54) (31.34) (31.34) (31.54) (31.54) (31.54) (31.54) 
Spline Major mm 29.89 29.89 29.89 30.48 29.89 29.89 29.89 29.89
Diameter (in) (1.18) (1.18) (1.18) (1.20) (1.18) (1.18) (1.18) (1.18)
Fix Bolt Size M10 M10 M10 M10 M10 M10 M10 M10
* OBS - Outboard Slip (Spline Engagement to T/M)


BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

4A-4 PROPELLER SHAFT
4
×2 Model
Engine Model 4JA1-T(L) 4JA1-
TC 4JA1-TC
Transmission Type 5 M/T
(MSG) 5 M/T
(MSG/MUA)5 M/T
(MUA)
5M/T (MUA) 4A/T
W heel Base Long Long Long Long Extra Long Long
Front Suspension  High Ride
Suspension High Ride
Suspension
Except High Ride
Suspension
 
Rear Axle φ194mm φ220mm ← ← ← ← ←
Type OBS ← ← ← ← ← ←
Outside Diameter mm 63.5 75 75 68.9 68.9 68.9 63.5
(in) (2.50) (2.95) (2.95) (2.71) (2.71) (2.71) (2.50)
Inside Diameter mm 60.3 71.8 71.8 64.9 64.9 64.9 60.3
(in) (2.37) (31.48) (31.48) (2.56) (2.56) (2.56) (2.37)
Length 1st(L1) mm 798.5 799.5 782.5 798.5 801.5 946.5 720.5
(in) (31.44) (31.48) (30.81) (31.44) (31.56) (37.26) (28.37)
2nd(L2) mm 819 801 796 801 796 801 801
(in) (32.24) (31.54) (31.34) (31.54) (31.34) (31.54) (31.54)
Spline Major mm 29.89 29.89 29.89 29.89 29.89 29.89 29.89
Diameter (in) (1.18) (1.18) (1.18) (1.18) (1.18) (1.18) (1.18)
Fix Bolt Size M10 M10 M10 M10 M10 M10 M10
* OBS - Outboard Slip (Spline Engagement To T/M)


4 ×2 Model
Engine Model C24SE HFV6
Transmission Type 5M/T (MUA) 5M/T (AR-5) 4A/T
W heel Base
Long Extra Long Long Extra Long Long Extra Long
Front Suspension High Ride
Suspension Except High
Ride
Suspension 
High Ride
Suspension ←
← ←
Rear Axle φ220mm ← ←
← ← ← ←
Type OBS ← ←
← ← ← ←
Outside Diameter mm 75 75 75 68.9 68.9 75 75
(in) (2.95) (2.95) (2.95) (2.71) (2.71) (2.95) (2.95)
Inside Diameter mm 71.8 71.8 71.8 64.9 64.9 71.8 71.8
(in) (2.83) (2.83) (2.83) (2.56) (2.56) (2.83) (2.83)
Length 1st(L1) mm 823.5 820.5 970.5 777.5 925.5 784.5 934.5
(in) (32.42) (32.30) (38.21) (30.61) (36.43) (30.89) (36.79)
2nd(L2) mm 801 796 796 801 801 801 801
(in) (31.54) (31.34) (31.34) (31.54) (31.54) (31.54) (31.54)
Spline Major mm 29.89 29.89 29.89 29.89 29.89 30.48 30.48
Diameter (in) (1.18) (1.18) (1.18) (1.18) (1.18) (1.20) (1.20)
Fix Bolt Size M10 M10 M10 M10 M10 M10 M10
* OBS - Outboard Slip (Spline Engagement To T/M)

BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

PROPELLER SHAFT 4A-5
4 ×4 Model
Engine Model 4JA1-T(L) 4JA1-TC 4JH1-TC
Transmission Type 5M/T (MUA) 5M/T (MUA) 4A/T
W heel Base Long Long Extra Long Long
Front Suspension    
Rear Axle φ220mm ← ← ←
Type OBS ← ← ←
Outside Diameter mm 75 68.9 68.9 63.5
(in) (2.95) (2.71) (2.71) (2.50)
Inside Diameter mm 71.8 64.9 64.9 60.3
(in) (2.83) (2.56) (2.56) (2.37)
Length 1st(L1) mm 469.5 468.5 616.5 402.5
(in) (18.48) (18.44) (24.27) (15.85)
2nd(L2) mm 801 801 801 801
(in) (31.54) (31.54) (31.54) (31.54)
Spline Major mm 29.89 29.89 29.89 29.89
Diameter (in) (1.18) (1.18) (1.18) (1.18)
Fix Bolt Size M10 M10 M10 M10
* OBS - Outboard Slip (Spline Engagement To T/M)


4 ×4 Model
Engine Model C24SE HFV6
Transmission Type 5M/T
(MUA) 5M/T (AR-5)
4A/T
W heel Base Long Long Extra Long Long
Front Suspension    
Rear Axle φ220mm
← ← ←
Type OBS
← ← ←
Outside Diameter mm 63.5 68.9 68.9 75
(in) (2.50) (2.71) (2.71) (2.95)
Inside Diameter mm 60.3 64.9 64.9 71.8
(in) (2.37) (2.56) (2.56) (2.83)
Length 1st(L1) mm 495.5 476.5 624.5 484.5
(in) (19.51) (18.75) (24.59) (19.07)
2nd(L2) mm 801 801 801 801
(in) (31.54) (31.54) (31.54) (31.54)
Spline Major mm 29.89 29.89 29.89 29.89
Diameter (in) (1.18) (1.18) (1.18) (1.18)
Fix Bolt Size M10 M10 M10 M10
* OBS - Outboard Slip (Spline Engagement To T/M)


BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

PROPELLER SHAFT 4A-7
Front Propeller Shaft

4×4 Model
Engine Model 4JK1 (Standard Output),
4JJ1 (Standard Output) 4JJ1 (High Output)
4JJ1 (Standard Output),
4JJ1 (High Output)
Transmission Type 5M/T (MUA) 5M/T (MUX) 4A/T
W heel Base Long Long Long
Outside Diameter mm 40 40 40
(in) (1.57) (1.57) (1.57)
Inside Diameter mm 32 32 32
(in) (1.26) (1.26) (1.26)
Length (L) mm 579 618 649
(in) (22.80) (24.33) (25.55)
Spline Outside
Diameter mm
33
33
33
(in) (1.30) (1.30) (1.30)

Fix Bolt Size T/F M10 M10 M10
Axle M10 M10 M10

4 ×4 Model
Engine Model 4JA1-T(L) 4JA1-TC 4JH1-TC C24SE HFV6
Transmission Type 5M/T (MUA) 5M/T (MUA) 4A/T 5M/T
(MUA) 5M/T (AR-5),
4A/T
W heel Base Long Long Long Long Long
Outside Diameter mm 40 40 40 40 40
(in) (1.57) (1.57) (1.57) (1.57) (1.57)
Inside Diameter mm 32 32 32 32 32
(in) (1.26) (1.26) (1.26) (1.26) (1.26)
Length (L) mm 607 607 676 586 596
(in) (23.90) (23.90) (26.61) (23.07) (23.46)
Fix Bolt Size T/F M10 M10 M10 M10 M10
Axle M10 M10 M10 M10 M10










RUW 54ASF000401

BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007