2007 ISUZU KB P190 light

FRAME AND BUMPER 2A-3
Important Operations - Removal
1. Radiator Grille
Refer to the Radiator Grille in this section.



RTW 72ASH000501
2. Front Bumper Fascia

• Remove the 7 clips and 4 bolts.
• Disconnect the fog light harness connectors.




RTW 52ASH000401
5. Bumper Seal
Remove the 6 clips.


Important Operations - Installation




RTW 52ASH000301
7. Front Bumper Impact Bar Assembly
Tighten the fixing bolts to the specified torque.

Torque N ⋅m(kgf ⋅m/lb ⋅ft)
62 (6.3 / 46)


BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

2A-4 FRAME AND BUMPER


RTW 72ASH000601


4. Fog Light
Tighten the fixing nuts to the specified torque.

Torque N ⋅m(kgf ⋅m/lb ⋅in)
7 (0.7 / 61)


BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

FRAME AND BUMPER 2A-5
FRONT BUMPER (B TYPE)
REMOVAL AND INSTALLATION


RTW 52ALF000501

Removal Steps
1. Front combi lamp assembly
2. Radiator grille
3. Front bumper fascia
4. Bezel (W /O fog light)
5. Fog light
6. Bumper seal
7. Front bumper flare assembly (W / Front
wheel extension)
8. Horn
9. Front bumper impact support assembly
10. Front bumper impact bar assembly
11. Fascia support side bracket
12. Fascia support lower bracket

Installation Steps

12. Fascia support lower bracket
11. Fascia support side bracket
10. Front bumper impact bar assembly
9. Front bumper impact support assembly
8. Horn
7. Front bumper flare assembly (W / Front
wheel extension)
6. Bumper seal
5. Fog light
4. Bezel (W /O fog light)
3. Front bumper fascia
2. Radiator grille
1. Front combi lamp assembly


BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

2A-6 FRAME AND BUMPER
Important Operations - Removal
1. Front Combi Lamp Assembly
2. Radiator Grille
Refer to the Radiator Grille in this section.




RTW 52ASH000101
3. Front Bumper Fascia

• Remove the 9 clips and 4 screws.
• Disconnect the fog light harness connectors.







RTW 52ASH000401
6. Bumper Seal
Remove 6 clips.

Important Operations - Installation


10. Front Bumper Impact Bar Assembly
Tighten the fixing bolts to the specified torque.

Torque N ⋅m(kgf ⋅m/lb ⋅ft)
62 (6.3 / 46)





7. Front Bumper Flare Assembly
Tighten the fixing nuts to the specified torque.

Torque N ⋅m(kgf ⋅m/lb ⋅in)
7 (0.7 / 61)


BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

FRAME AND BUMPER 2A-7


5. Fog Light
Tighten the fixing nuts to the specified torque.

Torque N ⋅m(kgf ⋅m/lb ⋅in)
7 (0.7 / 61)






BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

2A-8 FRAME AND BUMPER
REAR STEP BUMPER
REMOVAL AND INSTALLATION





RTW 72ALF000401

Removal Steps
1. Rear step bumper assembly
2. Side step pad
3. License plate light
4. Rear bumper center pad
5. Extension harness
6. Center bar
7. Shell
8. Back bar / corner brace
9. Reinforcement assembly

Installation Steps

9. Reinforcement assembly
8. Back bar / corner brace
7. Shell
6. Center bar
5. Extension harness
4. Rear bumper center pad
3. License plate light
2. Side step pad
1. Rear step bumper assembly



BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

SHEET METAL 2B-3

RUW 52BSH002501

Important Operations - Removal
1. Washer Nozzle Tube
1) Open the hood.
2) Support the hood.
3) Remove the windshield washer nozzle tube.





RUW 52BSH002601

2. Hood Hinge Bolt
• Before removing the hinges from the engine hood, scribe a
mark showing location of the hinges to facilitate installation in
the original position.






RTW 72BSH000501

Important Operations - Installation
3. Engine Hood
• Check the engine hood and fender (1).





• Clearance : 4.0 mm (0.16 in)
• Height (step) : Flushness
• Adjust clearance using the hinges on the engine hood.



RTW 72BSH000701







• Adjust height (step) using the hood rests (1).






Engine Hood Striker
• Apply a light coat of grease to the striker.



BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

SHEET METAL 2B-7



• Clearance : 4.0 mm (0.16 in)
• Height (step) : Flushness
• Adjust clearance using the hinges on the engine hood.



RTW 72BSH000701







• Adjust height (step) using the hood rests (1).






Engine Hood Striker
• Apply a light coat of grease to the striker.



4. Hood Hinge Bolt
• Tighten the engine hood hinge fixing bolts to the specified
torque.

Torque N ⋅m(kgf ⋅m/lb ⋅in)
10 (1.0 / 87)


BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007