2007 ISUZU KB P190 air filter

TROUBLESHOOTING 6 – 5
2. Unstable Idling
Step Action Value(s) Yes No
1 Was the fuel line air bled completely? — Go to Step 3 Bleed the air
2 Was the fuel line leakage or blockage found? — Repair or
replace relation parts. Go to Step 4
3 Was the water contained in the fuel? — Replace the
fuel Go to Step 5
4 Was the fuel filter element clogged? — Replace the
fuel filter element Go to Step 6
5 Was the injection starting pressure or the injection
spray condition OK? (See below)
Go to Step 7 Replace the
injection nozzle
6 Was the injection nozzle sticking? See Step 6 Replace the
injection nozzle Go to Step 8
7 Check the throttle valve condition.
Was the idling port clogged in the throttle valve? —
Repair or
replace the
throttle valve Go to Step 9
8 Was the valve clearance improper adjusted? 0.4 mm
(0.016 in)
both intake
and exhaust valves Adjust the
valve clearance Go to Step 10
9 Was the compression pressure OK? 3,040 kPa
(31 kg/cm2,
441 psi) at 200rpm
Go to Step 11 Readjust the
valve clearance or replace the cylinder head gasket or
cylinder liner or
piston or piston ring or valve
and valve seat
10 Are any DTC stored? — Go to indicated
DTC Solved

Injection nozzle opening pressure
1st = 19.5 MPa (199 kg/cm2, 2828 psi)

BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

6 – 6 TROUBLESHOOTING
3. Insufficient Power
Step Action Value(s) Yes No
1 Was the air cleaner element condition OK? (Clogged
or not) —

Go to Step 2 Clean or
replace the air cleaner
element.
2 Was the intake air leakage found from intake system? —
Repair or
replace the intake air system. Go to Step 3
3 Was the fuel filter element condition OK? (Clogged
or not) —

Go to Step 4 Clean or
replace the fuel filter element.
4 Check the fuel injection pipes. Does the injection pipes have obstruction or any
damage? —
Repair or
replace the fuel injection pipes. Go to Step 5
5 Was the water contained in the fuel? — Replace the
fuel Go to Step 6
6 Was the injection nozzle pressure or spray pattern
normal? —

Go to Step 7 Readjust the
injection nozzle pressure or replace the nozzle.
7 Was the compression pressure OK? 3.0 MPa
(31.0 kg/cm2,
441 psi) at 200 rpm
Go to Step 8 Readjust the
valve clearance or replace the cylinder head gasket or
cylinder liner or
piston or piston ring or valve
and valve seat
8 Was the exhaust pipe clogged? — Repair or
replace the
exhaust pipe. Go to Step 9
9 Was the exhaust gas leakage found from exhaust
system? —
Repair or
replace the exhaust system. Go to Step 10
10 Was the waste gate control actuator hose broken or
cracked? —
Replace the
hose. Go to Step 11
11 Was the waste gate working completely? —
Go to Step 12 Replace the
turbocharger assembly.
12 Was turbocharger working completely? —
Go to Step 13 Replace the
turbocharger assembly.
13 Are any DTC stored? — Go to indicated
DTC Solved


BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

TROUBLESHOOTING 6 – 11
9. Oil Pressure Does Not Rise
Step Action Value(s) Yes No
1 Was the oil pressure warning lamp working OK? —
Go to Step 2 Replace the oil
pressure
warning lamp
2 Does the oil filter element clog? — Replace the oil
filter element Go to Step 3
3 Does the relief valve open? — Repair or
replace the relief valve Go to Step 4
4 Does the oil strainer clog? — Clean or
replace the oil strainer Go to Step 5
5 Was the oil pump working OK? (The pump related
parts worn etc.) —

Go to Step 6 Repair or
replace the oil pump.
6 Was the rocker arm and/or relation parts worn? — Replace the
rocker arm
and/or relation parts Go to Step 7
7 Was the camshaft and/or relation parts worn? — Replace the
camshaft
and/or relation parts Go to Step 8
8 Was the crankshaft and/or relation parts worn? — Replace the
crankshaft
and/or relation parts Go to Step 9
9 Are any DTC stored? — Go to indicated
DTC Solved

Table of pressure unit
Pressure kPa (kg/cm
2) 100
(1.0) 980
(10.0)
Resistance ohm 81 30
Electric current A 63.5 106.7

BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

ENGINE MECHANICAL 6A – 3
Lubricating Flow ........................................................................................................ 6A- 126
Oil Pump and Oil Filter .............................................................................................. 6A- 127
Oil Pump ..................................................................................................................... 6 A- 128
Disassembly ........................................................................................................... 6A- 128
Inspection and Repair ............................................................................................ 6A- 129
Reassembly ............................................................................................................ 6A- 130
Oil Filter and Oil Cooler ............................................................................................. 6A- 131 Disassembly ........................................................................................................... 6A- 131
Inspection and Repair ............................................................................................ 6A- 132
Reassembly ............................................................................................................ 6A- 133
Inter Cooler .................................................................................................................. . 6A- 135
Removal ................................................................................................................. 6A- 1 36
Installation ............................................................................................................. 6A- 136
Special Tools ................................................................................................................. 6A- 137

BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

6A – 24 ENGINE MECHANICAL

SERVICING
Servicing refers to general maintenance procedures to be performed by qualified service personnel.


RTW 36ASH000401
MODEL IDENTIFICATION
Engine Serial Number
The engine number is stamped on the rear left hand side
of the cylinder body.
The engine number is stamped in the plate in front of the
engine room as well.


AIR CLEANER
Element cleaning procedures will vary according to the
condition of the element.

Dust Fouled Element (Except wet type element)
Rotate the element with your hand while applying
compressed air to the inside of the element. This will blow
the dust free.
Compressed air pressure kPa (kg/cm
2 /psi)
392 – 490 (4 – 5/57 – 71)


LUBRICATING SYSTEM
Main Oil Filter (Cartridge Type Paper Element)
Replacement Procedure
1. Drain the engine oil.
2. Retighten the drain plug.
3. Loosen the used oil filter by turning it counterclockwise with a filter wrench.
Filter W rench: 5-8840-0200-0


RTW 36ASH000101



4. Clean the oil cooler fitting face. This will allow the new oil filter to seat properly.
5. Apply a light coat of engine oil to the filter O-ring.
6. Turn in the new oil filter until the filter O-ring is fitted against the sealing face.
7. Use the filter wrench to turn in the filter an additional 2/3 turns.
Filter W rench: 5-8840-0200-0
8. Check the engine oil level and replenish to the specified level if required.
130RY00003
6A-6

BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

ENGINE MECHANICAL 6A – 25
Replenished Engine Oil MAX lit (US/UK gal)
Condition


Model Engine Dry
W ith oil filter
replacement W ithout oil
filter
replacement
4 × 2
4 × 4
(4JA1L/TC)6.2 (1.64/1.36) 5.2 ∼ 4.2
(1.37 ∼ 1.11
/ 1.14 ∼ 0.92) 4.5
∼ 3.5
(1.19 ∼ 0.93
/ 0.99 ∼ 0.77)
4 × 2
(4JH1TC)
6.2 (1.64/1.36) 5.2
∼ 4.2
(1.37 ∼ 1.11
/ 1.14 ∼ 0.92) 4.5
∼ 3.5
(1.19 ∼ 0.93
/ 0.99 ∼ 0.77)
4 × 4
(4JH1TC) 7.0 (1.85/1.54) 6.2 ∼ 5.2
(1.64 ∼ 1.37
/ 1.36 ∼ 1.14) 5.3
∼ 4.3
(1.72 ∼ 1.14
/ 1.17 ∼ 0.95)

9. Start the engine and check for oil leakage from the
main oil filter.



RTW 66ASH003201




FUEL SYSTEM
Fuel Filter Replacement Procedure
1. Remove the fuel filter by turning it counterclockwise with a filter wrench.
Filter W rench: 5-8840-0253-0 (J-22700)
Note:
Be careful not to spill the fuel in the filter cartridge.




RTW 66ASH003301








2. Clean the fuel filter cartridge fitting faces. This will allow the new fuel filter to seat properly
3. Apply a light coat of engine oil to the O-ring.
4. Turn in the fuel filter until the sealing face comes in contact with the O-ring.
5. Turn in the fuel filter an additional 2/3 of a turn with a filter wrench.
Filter W rench : 5-8840-0253-0 (J-22700)




6. Operate the priming pump until the air discharged completely from fuel system.
7. Start the engine and check for fuel leakage.
Note:
The use of an ISUZU genuine fuel filter is strongly
recommended.

041RY00009

BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

6A – 26 ENGINE MECHANICAL



041RY00011
Draining Procedure
The indicator light will come on when the water level in the
water separator exceeds the specified level.
Drain the water and foreign material from the water
separator (inside chassis frame) with the following
procedure.





1. Place the drain pan under the drain plug.
2. Loosen the drain plug and drain water.
3. After draining the water, tighten the drain plug.
4. Operate the priming pump on the fuel filter several times and check for fuel leakage.
5. Check the water separator indicator light. It should be off.



Except EURO III model
RTW 46ASH002901




For EURO III model
RTW 46ASH000501


Air Bleeding
1. Operate the priming pump until strong resistance is felt.
2. W ait 1 minute, and operate the priming pump until strong resistance is felt.
3. Once more wait, and operate the priming pump until strong resistance is felt.
4. Turn the ignition switch to the "ON" position. W ait until the glow indicator lamp turns off.
5. Turn the ignition switch to the "START" position and crank the engine until it starts.
6. If the engine does not start, repeat Step 3 - 5.
7. Allow the engine to idle for 3 minutes to bleed air completely form the fuel system and check for fuel
leakage.
Note:
Insufficient air bleeding may cause the Diagnostic
Trouble Code (DTC) store or improper engine
performance.

BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

6A – 42 ENGINE MECHANICAL

ENGINE REPAIR KIT




RTW 36ALF000601

Removal Steps
1. Cylinder head gasket
2. Head cover gasket
3. Head cover cap nut gasket
4. Drain cock gasket
5. Crankshaft rear oil seal
6. Gear case gasket
7. Oil pan drain plug gasket
8. Oil pan gasket
9. Oil filter gasket
10. Joint bolt gasket
11. Vacuum pump gasket
12. W ater pump O-ring
13. W ater outlet pipe gasket
14. Intake pipe gasket
15. Thermostat housing gasket
16. Intake manifold gasket
17. Exhaust manifold gasket
18. Nozzle holder O-ring
19. Nozzle holder gasket
20. Crankshaft front oil seal

NOTE
Discard all O-rings, gaskets, and seals removed at disassembly and replace them with new ones. Reuse of
these parts will result in oil, water, and gas leakage.

BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007