2007 INFINITI M35 diagram

AV-28
[WITHOUT MOBILE ENTERTAINMENT SYSTEM]
SYSTEM DESCRIPTION
Revision: 2007 April2007 M35/M45
Wiring Diagram — AV — / BOSE Audio 2ch SystemNKS0048G
TKWT5310E

SYSTEM DESCRIPTION
AV-45
[WITHOUT MOBILE ENTERTAINMENT SYSTEM]
C
D
E
F
G
H
I
J
L
MA
B
AV
Revision: 2007 April2007 M35/M45
Wiring Diagram — AV — / BOSE Surround Audio 5.1ch SystemNKS0048I
TKWT5319E

AV-152
[WITH MOBILE ENTERTAINMENT SYSTEM]
SYSTEM DESCRIPTION
Revision: 2007 April2007 M35/M45
Wiring Diagram — AV — / BOSE Audio 2ch SystemNKS004AG
TKWT5325E

AV-174
[WITH MOBILE ENTERTAINMENT SYSTEM]
SYSTEM DESCRIPTION
Revision: 2007 April2007 M35/M45
Wiring Diagram — AV — / BOSE Surround Audio 5.1ch SystemNKS004AI
TKWT5329E

BCS-14
BCM (BODY CONTROL MODULE)
Revision: 2007 April2007 M35/M45
Check BCM Power Supply and Ground CircuitNKS003XM
1. CHECK FUSES AND FUSIBLE LINK
Check for blown fuses and fusible link.
Refer to LT-13, "Wiring Diagram — H/LAMP —" .
OK or NG
OK >> GO TO 2.
NG >> If fuse or fusible link is blown, be sure to eliminate cause of malfunction before installing new fuse
or fusible link. Refer to PG-3, "
POWER SUPPLY ROUTING CIRCUIT" .
2. CHECK POWER SUPPLY CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect BCM connector.
3. Check voltage between BCM harness connector and ground.
OK or NG
OK >> GO TO 3.
NG >> Repair harness or connector.
3. CHECK GROUND CIRCUIT
Check continuity between BCM harness connector and ground.
OK or NG
OK >> INSPECTION END
NG >> Repair harness or connector.
Unit Power source Fuse and fusible link No.
BCMBatteryF
21
Ignition switch ON or START position 1
Ignition switch ACC or ON position 6
Terminal Ignition switch position
(+)
(-) OFF ACC ON
BCM
ConnectorTerminal
M111
GroundApprox. 0 VBattery
voltageBattery
voltage
38 Approx. 0 V Approx. 0 VBattery
voltage
M242 Battery
voltageBattery
voltageBattery
voltage
55 Battery
voltageBattery
voltageBattery
voltage
PKIA5204E
Terminal Continuity
BCM
ConnectorTerminal
Ground Yes
M2 52
SKIB5125E

BL-1
BODY, LOCK & SECURITY SYSTEM
I BODY
CONTENTS
C
D
E
F
G
H
J
K
L
M
SECTION BL
A
B
BL
Revision: 2007 April2007 M35/M45
BODY, LOCK & SECURITY SYSTEM
PRECAUTIONS .......................................................... 6
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” .................................................................. 6
Precautions for Procedures without Cowl Top Cover ..... 6
Precautions Necessary for Steering Wheel Rotation
After Battery Disconnect .......................................... 6
OPERATION PROCEDURE ................................. 6
Precautions for Work ................................................ 7
PREPARATION ........................................................... 8
Special Service Tools ............................................... 8
Commercial Service Tools ........................................ 8
SQUEAK AND RATTLE TROUBLE DIAGNOSIS ...... 9
Work Flow ................................................................ 9
CUSTOMER INTERVIEW ..................................... 9
DUPLICATE THE NOISE AND TEST DRIVE ..... 10
CHECK RELATED SERVICE BULLETINS ......... 10
LOCATE THE NOISE AND IDENTIFY THE
ROOT CAUSE .................................................... 10
REPAIR THE CAUSE ......................................... 10
CONFIRM THE REPAIR ...................................... 11
Generic Squeak and Rattle Troubleshooting .......... 11
INSTRUMENT PANEL ......................................... 11
CENTER CONSOLE ............................................ 11
DOORS ................................................................ 11
TRUNK ................................................................ 12
SUNROOF/HEADLINING ................................... 12
SEATS ................................................................. 12
UNDERHOOD ..................................................... 12
Diagnostic Worksheet ............................................ 13
HOOD ....................................................................... 15
Fitting Adjustment .................................................. 15
Removal and Installation of Hood Assembly .......... 17
REMOVAL ........................................................... 17
INSTALLETION ................................................... 18
Removal and Installation of Hood Lock Control ..... 18
REMOVAL ........................................................... 18
INSTALLATION ................................................... 19
Hood Lock Control Inspection ................................ 20RADIATOR CORE SUPPORT .................................. 21
Removal and Installation ........................................ 21
REMOVAL ........................................................... 21
INSTALLATION ................................................... 22
FRONT FENDER ...................................................... 23
Removal and Installation ........................................ 23
REMOVAL ........................................................... 23
INSTALLATION ................................................... 23
POWER DOOR LOCK SYSTEM .............................. 24
Component Parts and Harness Connector Location ... 24
System Description ................................................. 25
DOOR LOCK ACTUATOR OPERATION ............. 26
FUEL LID OPERATION ....................................... 26
OUTLINE ............................................................. 26
CAN Communication System Description .............. 26
CAN Communication Unit ....................................... 26
Schematic ............................................................... 27
Wiring Diagram —D/LOCK— ................................. 28
Terminals and Reference Value of BCM ................. 31
Work Flow ............................................................... 31
CONSULT-II Function (BCM) ................................. 32
CONSULT-II START PROCEDURE .................... 32
CONSULT-II APPLICATION ITEMS .................... 32
Trouble Diagnosis Chart by Symptom .................... 33
Power Supply and Ground Circuit Check of BCM ... 34
Check Door Lock and Unlock Switch ..................... 35
Check Door Lock Actuator/Driver Side ................... 37
Check Door Lock Actuator/Passenger Side ........... 38
Check Door Lock Actuator/Rear LH ....................... 39
Check Door Lock Actuator/Rear RH ....................... 39
Check Fuel Lid Opener Actuator ............................ 40
Door Key Cylinder Switch Check ............................ 41
INTELLIGENT KEY SYSTEM ................................... 43
Component Parts and Harness Connector Location ... 43
System Description ................................................. 47
DOOR LOCK/UNLOCK/TRUNK OPEN FUNC-
TION .................................................................... 47
REMOTE KEYLESS ENTRY FUNCTIONS ......... 51
ENGINE START FUNCTION ............................... 53
WARNING FUNCTION ........................................ 54

BL-2Revision: 2007 April2007 M35/M45 CHANGE SETTINGS FUNCTION ....................... 59
INTELLIGENT KEY REGISTRATION .................. 59
STEERING LOCK UNIT REGISTRATION .......... 59
CAN Communication System Description .............. 59
CAN Communication Unit ....................................... 59
Schematic ............................................................... 60
Wiring Diagram — I/KEY— .................................... 62
Terminals and Reference Value for Intelligent Key
Unit ......................................................................... 73
Terminals and Reference Value for BCM ................ 76
Terminals and Reference Value for IPDM E/R ........ 76
Trouble Diagnosis Procedure ................................. 77
WORK FLOW ...................................................... 77
CONSULT-II Functions (INTELLIGENT KEY) ........ 79
CONSULT-II Inspection Procedure ......................... 79
BASIC OPERATION ............................................ 79
CONSULT-II Application Items ............................... 79
SELF-DIAGNOSTIC RESULTS ........................... 79
DATA MONITOR .................................................. 80
WORK SUPPORT ............................................... 81
ACTIVE TEST ..................................................... 83
Trouble Diagnosis Symptom Chart ......................... 84
ALL FUNCTIONS OF INTELLIGENT KEY SYS-
TEM DOES NOT OPERATE ............................... 84
DOOR LOCK/UNLOCK FUNCTION MALFUNC-
TION .................................................................... 84
REMOTE KEYLESS ENTRY FUNCTION MAL-
FUNCTION .......................................................... 85
TRUNK OPEN FUNCTION MALFUNCTION ...... 86
HAZARD AND BUZZER REMINDER FUNC-
TION MALFUNCTION ......................................... 87
HAZARD AND HORN REMINDER FUNCTION
MALFUNCTION ................................................... 87
POWER WINDOW DOWN FUNCTION MAL-
FUNCTION .......................................................... 88
WARNING FUNCTION MALFUNCTION ............. 88
Check CAN Communication System ...................... 90
Check Power Supply and Ground Circuit ............... 91
Check Key Slot ....................................................... 92
Check Door Switch ................................................. 94
Check Trunk Room Lamp Switch ........................... 97
Check Door Request Switch ................................... 99
Check Trunk Opener Request Switch ..................101
Check Unlock Sensor ...........................................103
Check Intelligent Key Warning Buzzer .................105
Check Outside Key Antenna (Driver Side and Pas-
senger Side) .........................................................106
Check Outside Key Antenna (Trunk Room) .........108
Check Inside Key Antenna ...................................110
Check Park Position Switch ..................................113
Check Ignition Switch Position .............................115
Check Remote Keyless Entry Receiver ................115
Check Trunk Lid Opener Cancel Switch ...............119
Check Key Slot Illumination ..................................121
Check Horn Function ............................................122
Check Combination Meter Display Function .........122
Check Warning Chime Function ...........................123
Removal and Installation of Intelligent Key Unit ...123
REMOVAL .........................................................123INSTALLATION ..................................................123
Intelligent Key Battery Replacement .....................124
DISASSEMBLY AND ASSEMBLY OF INTELLI-
GENT KEY .........................................................124
INTELLIGENT KEY BATTERY INSPECTION ...124
INTELLIGENT KEY SYSTEM/ENGINE START
FUNCTION ..............................................................125
Component Parts and Harness Connector Location .125
System Description ...............................................126
PRECAUTIONS FOR INTELLIGENT KEY SYS-
TEM ...................................................................127
Operation Description ...........................................127
SYSTEM DIAGRAM ..........................................127
OPERATION WHEN INTELLIGENT KEY IS
CARRIED ...........................................................127
OPERATION WHEN KEY SLOT IS USED ........128
PUSH-BUTTON IGNITION SWITCH OPERA-
TION PROCEDURE ..........................................128
CAN Communication System Description ............129
CAN Communication Unit .....................................129
Schematic .............................................................130
Wiring Diagram — ENG/ST — ..............................132
Terminals and Reference Value for Intelligent Key
Unit ........................................................................141
Terminals and Reference Value for Steering Lock
Unit ........................................................................145
Terminals and Reference Value for BCM ..............145
Terminals and Reference Value for IPDM E/R ......146
Terminals and Reference Value for PDU ..............147
Work Flow .............................................................148
CONSULT-II Functions (INTELLIGENT KEY) .......150
CONSULT-II Inspection Procedure .......................150
BASIC OPERATION ..........................................150
CONSULT-II Application Items ..............................150
SELF-DIAGNOSTIC RESULTS .........................150
DATA MONITOR ................................................151
WORK SUPPORT .............................................152
ACTIVE TEST ....................................................153
DTC B2013 STRG COMM 1 .................................155
DIAGNOSIS DESCRIPTION .............................155
TERMINALS AND REFERENCE VALUE FOR
INTELLIGENT KEY UNIT ..................................155
SELF-DIAGNOSTIC LOGIC ..............................155
DIAGNOSTIC PROCEDURE .............................155
DTC B2551 STEERING LOCK UNIT ....................157
DIAGNOSIS DESCRIPTION .............................157
TERMINALS AND REFERENCE VALUE ..........157
SELF-DIAGNOSTIC LOGIC ..............................158
DIAGNOSTIC PROCEDURE .............................158
DTC B2552 INTELLIGENT KEY ...........................161
DIAGNOSIS DESCRIPTION .............................161
DTC B2553 IGN POWER CIRCUIT ......................161
DIAGNOSIS DESCRIPTION .............................161
TERMINAL AND REFERENCE VALUE FOR
INTELLIGENT KEY UNIT ..................................161
CONSULT-II DATA MONITOR STANDARD
VALUE ...............................................................161
SELF-DIAGNOSTIC LOGIC ..............................162
DIAGNOSTIC PROCEDURE .............................162

BL-3
C
D
E
F
G
H
J
K
L
MA
B
BL
Revision: 2007 April2007 M35/M45 DTC B2554 ACC POWER CIRCUIT .................... 162
DIAGNOSIS DESCRIPTION ............................. 162
TERMINALS AND REFERENCE VALUE FOR
INTELLIGENT KEY UNIT ................................. 163
CONSULT-II DATA MONITOR STANDARD
VALUE ............................................................... 163
SELF-DIAGNOSTIC LOGIC ............................. 163
DIAGNOSTIC PROCEDURE ............................ 164
DTC B2555 STOP LAMP CIRCUIT ..................... 165
DIAGNOSIS DESCRIPTION ............................. 165
TERMINALS AND REFERENCE VALUE FOR
INTELLIGENT KEY UNIT INPUT ...................... 165
CONSULT-II DATA MONITOR STANDARD
VALUE ............................................................... 165
SELF-DIAGNOSTIC LOGIC ............................. 165
DIAGNOSTIC PROCEDURE ............................ 166
DTC B2556 ENG START SW .............................. 166
DIAGNOSIS DESCRIPTION ............................. 166
TERMINALS AND REFERENCE VALUE FOR
INTELLIGENT KEY UNIT ................................. 166
SELF-DIAGNOSTIC LOGIC ............................. 166
DIAGNOSTIC PROCEDURE ............................ 167
DTC B2557 VEHICLE SPEED ............................. 167
DIAGNOSIS DESCRIPTION ............................. 167
TERMINALS AND REFERENCE VALUE FOR
INTELLIGENT KEY UNIT ................................. 168
SELF-DIAGNOSTIC LOGIC ............................. 168
DIAGNOSTIC PROCEDURE ............................ 168
DTC B2558 SHIFT POSITION ............................. 170
DIAGNOSIS DESCRIPTION ............................. 170
TERMINALS AND REFERENCE VALUE FOR
INTELLIGENT KEY UNIT ................................. 170
SELF-DIAGNOSTIC LOGIC ............................. 170
DIAGNOSTIC PROCEDURE ............................ 170
DTC B2559 PDU .................................................. 172
DIAGNOSIS DESCRIPTION ............................. 172
DTC B2560 START POW SUP CIRC .................. 172
DIAGNOSIS DESCRIPTION ............................. 172
TERMINALS AND REFERENCE VALUE ......... 173
SELF-DIAGNOSTIC LOGIC ............................. 173
DIAGNOSTIC PROCEDURE ............................ 173
DTC B2562 LOW VOLTAGE ................................ 175
DIAGNOSIS DESCRIPTION ............................. 175
TERMINALS AND REFERENCE VALUE FOR
INTELLIGENT KEY UNIT ................................. 175
SELF-DIAGNOSTIC LOGIC ............................. 175
DIAGNOSTIC PROCEDURE ............................ 175
DTC B2563 HI VOLTAGE .................................... 176
DIAGNOSIS DESCRIPTION ............................. 176
TERMINAL AND REFERENCE VALUE FOR
INTELLIGENT KEY UNIT ................................. 176
SELF-DIAGNOSTIC LOGIC ............................. 176
DIAGNOSTIC PROCEDURE ............................ 177
Trouble Diagnosis Symptom Chart 1 ................... 177
CONDITIONS OF VEHICLE (OPERATING CON-
DITIONS) .......................................................... 177
Trouble Diagnosis Symptom Chart 2 ................... 178
CONDITIONS OF VEHICLE (OPERATING CON-
DITIONS) .......................................................... 178Trouble Diagnosis Symptom Chart 3 ....................178
CONDITIONS OF VEHICLE (OPERATING CON-
DITIONS) ...........................................................178
Check CAN Communication System ....................179
Check Push-Button Ignition Switch ......................179
Check Inside Key Antenna ...................................181
Check Remote Keyless Entry Receiver ................183
Check Key Switch Built In Key Slot ......................184
Check NATS Antenna Amp. Built In Key Slot .......186
DOOR ......................................................................188
Fitting Adjustment .................................................188
FRONT DOOR ..................................................188
REAR DOOR .....................................................188
STRIKER ADJUSTMENT ..................................189
Removal and Installation of Front Door ................189
REMOVAL .........................................................189
INSTALLATION .................................................190
Removal and Installation of Rear Door .................190
REMOVAL .........................................................190
INSTALLATION .................................................191
Door Weatherstrip ................................................192
FRONT DOOR ..................................................192
REMOVAL .........................................................192
INSTALLATION .................................................192
REAR DOOR .....................................................193
REMOVAL .........................................................193
INSTALLATION .................................................193
FRONT DOOR LOCK .............................................194
Component Structure ............................................194
Removal and Installation ......................................194
REMOVAL .........................................................194
INSTALLATION .................................................197
REAR DOOR LOCK ...............................................198
Component Structure ............................................198
Removal and Installation ......................................198
REMOVAL .........................................................198
INSTALLATION .................................................200
TRUNK LID .............................................................201
Fitting Adjustment .................................................201
Removal and Installation of Trunk Lid Assembly ..202
REMOVAL .........................................................202
INSTALLATION .................................................203
Removal and Installation of Trunk Lid Stay ..........203
REMOVAL .........................................................203
INSTALLATION .................................................203
Removal and Installation of Trunk Lid Lock ..........204
REMOVAL .........................................................204
INSTALLATION .................................................204
Removal and Installation of Trunk Lid Striker .......205
REMOVAL .........................................................205
INSTALLATION .................................................205
Removal and Installation of Trunk Lid Weatherstrip .206
REMOVAL .........................................................206
INSTALLATION .................................................206
TRUNK LID OPENER .............................................207
Component Parts and Harness Connector Location .207
System Description ...............................................208
TRUNK LID OPENER OPERATION .................208
Wiring Diagram —TLID— .....................................209