2007 INFINITI M35 oil

AT-290
OVERHAUL
Revision: 2007 April2007 M35/M45
7. Pawl shaft 8. Seal ring 9. Needle bearing
10. Revolution sensor 11. Parking gear 12. Output shaft
13. Bearing race 14. Needle bearing 15. Manual plate
16. Parking rod 17. Manual shaft oil seal 18. Manual shaft
19. O-ring 20. Band servo anchor end pin 21. Detent spring
22. Spacer 23. Seal ring 24. Snap ring
25. Return spring 26. O-ring 27. Servo assembly
28. Snap ring 29. Sub-harness 30. Control valve with TCM
31. Bracket 32. A/T fluid temperature sensor 2 33. Clip
34. Oil pan mounting bolt 35. Oil pan 36. Magnet
37. Drain plug 38. Drain plug gasket 39. Oil pan gasket
40. Terminal cord assembly 41. O-ring 42. Retaining pin
43. Transmission case
Refer to GI section to make sure icons (symbol marks) in the figure. Refer to GI-11, "
Components" .
However, refer to the following symbols for others.
*:Apply Genuine Anaerobic Liquid Gasket or equivalent. Refer to GI-47, "Recommended Chemical Products and Sealants"
.

AT-292
OVERHAUL
Revision: 2007 April2007 M35/M45
1. Output shaft & companion flange
complement2. Parking actuator support 3. Parking pawl
4. Return spring 5. Pawl shaft 6. Self-sealing bolt
7. Seal ring 8. Needle bearing 9. Revolution sensor
10. Intermediate shaft 11. Manual plate 12. Parking rod
13. Manual shaft oil seal 14. Manual shaft 15. Retaining pin
16. O-ring 17. Band servo anchor end pin 18. Detent spring
19. Spacer 20. Return spring 21. Seal ring
22. O-ring 23. Servo assembly 24. Snap ring
25. Snap ring 26. Sub-harness 27. Control valve with TCM
28. Bracket 29. A/T fluid temperature sensor 2 30. Terminal cord assembly
31. O-ring 32. Clip 33. Bracket
34. Bracket 35. Oil pan mounting bolt 36. Oil pan
37. Magnet 38. Drain plug 39. Drain plug gasket
40. Oil pan gasket 41. Transmission case
Refer to GI section to make sure icons (symbol marks) in the figure. Refer to GI-11, "
Components" .
However, refer to the following symbols for others.
*:Apply Genuine Anaerobic Liquid Gasket or equivalent. Refer to GI-47, "Recommended Chemical Products and Sealants" .

OVERHAUL
AT-293
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: 2007 April2007 M35/M45
AWD models
SCIA8042E
1. Rear oil seal 2. Bracket 3. Adapter case
4. Parking actuator support 5. Parking pawl 6. Return spring

AT-294
OVERHAUL
Revision: 2007 April2007 M35/M45
7. Pawl shaft 8. Self-sealing bolt 9. Seal ring
10. Needle bearing 11. Gasket 12. Revolution sensor
13. Parking gear 14. Output shaft 15. Bearing race
16. Needle bearing 17. Manual plate 18. Parking rod
19. Manual shaft oil seal 20. Manual shaft 21. O-ring
22. Band servo anchor end pin 23. Detent spring 24. Spacer
25. Seal ring 26. Snap ring 27. Return spring
28. O-ring 29. Servo assembly 30. Snap ring
31. Sub-harness 32. Control valve with TCM 33. Bracket
34. A/T fluid temperature sensor 2 35. Clip 36. Oil pan mounting bolt
37. Oil pan 38. Magnet 39. Drain plug
40. Drain plug gasket 41. Oil pan gasket 42. Terminal cord assembly
43. O-ring 44. Retaining pin 45. Transmission case
Refer to GI section to make sure icons (symbol marks) in the figure. Refer to GI-11, "
Components" .

OVERHAUL
AT-295
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: 2007 April2007 M35/M45
Oil ChannelNCS001R1
VQ35DE models for 2WD
SCIA5185E

AT-302
DISASSEMBLY
Revision: 2007 April2007 M35/M45
6. Remove O-ring from input clutch assembly.
7. Remove tightening bolts for oil pump assembly and transmis-
sion case.
8. Attach the sliding hammers to oil pump assembly and extract it
evenly from transmission case.
CAUTION:

Fully tighten the sliding hammer screws.

Make sure that bearing race is installed to the oil pump
assembly edge surface.
9. Remove O-ring from oil pump assembly.
SCIA5011E
SCIA2300E
SCIA5474E
SCIA5172E

DISASSEMBLY
AT-303
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: 2007 April2007 M35/M45
10. Remove bearing race from oil pump assembly.
11. Remove needle bearing from front sun gear.
12. Remove front sun gear assembly from front carrier assembly.
NOTE:
Remove front sun gear by rotating left/right.
13. Remove seal rings from input clutch assembly.
14. Remove front carrier assembly from rear carrier assembly. (With
input clutch assembly and rear internal gear.)
CAUTION:
Be careful to remove it with needle bearing.
SCIA6529E
SCIA2808E
SCIA5014E
SCIA2470E
SCIA5015E

DISASSEMBLY
AT-307
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: 2007 April2007 M35/M45
29. Remove oil pan, oil pan gasket and clips (VQ35DE models) or oil pan, oil pan gasket, brackets and clips
(VK45DE models) according to the following procedures.
a. VQ35DE models
i. Remove clips (1).
ii. Remove oil pan (2) and oil pan gasket.
: Front
: Bolt (22)
b. VK45DE models
i. Remove clips (1) and brackets (2).
ii. Remove oil pan (3) and oil pan gasket.
: Front
: Bolt (22)
30. Check foreign materials in oil pan to help determine causes of
malfunction. If the ATF is very dark, smells burned, or contains
foreign particles, the frictional material (clutches, band) may
need replacement. A tacky film that will not wipe clean indicates
varnish build up. Varnish can cause valves, servo, and clutches
to stick and can inhibit pump pressure.

If frictional material is detected, perform A/T fluid cooler
cleaning. Refer to AT- 1 4 , "
A/T Fluid Cooler Cleaning" .
31. Remove magnets from oil pan.
SCIA8039E
SCIA8035E
SCIA5199E
SCIA5200E