2007 INFINITI FX35 ignition

GW-80
REAR WINDOW DEFOGGER
Revision: 2006 July 2007 FX35/FX45
3. CHECK REAR WINDOW DEFOGGER RELAY
Check continuity between rear window defogger terminals 3 and 5, 6
and 7.
OK or NG
OK >> GO TO 4.
NG >> Replace rear window defogger relay.
4. CHECK REAR WINDOW DEFOGGER RELAY GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Installation rear window defogger relay.
3. Turn ignition switch ON.
4. Check voltage between IPDM E/R connector and ground.
OK or NG
OK >> Rear window defogger power supply circuit is OK.
NG >> GO TO 5.
5. CHECK HARNESS CONTINUITY
1. Turn ignition switch OFF.
2. Disconnect IPDM E/R connector and rear window defogger relay.
3. Check continuity between IPDM E/R connector E9 terminal 52 and rear window defogger relay connector E13 terminal 2.
OK or NG
OK >> GO TO 6.
NG >> Repair or replace harness.
Terminal Condition Continuity
35 12V direct current supply
between terminals 1 and 2 Ye s
No current supply No
67 12V direct current supply
between terminals 1 and 2 Ye s
No current supply No
SEC202B
Connector Terminals (Wire color)
Condition Voltage (V)
(Approx.)
(+) (-)
E9 52 (G) Ground When rear window defog-
ger switch ON 0
When rear window defog-
ger switch OFF Battery
voltage
PIIA6210E
52 (G) – 2 (G) : Continuity should exist.
PIIA6211E

REAR WINDOW DEFOGGER GW-81
C
D E
F
G H
J
K L
M A
B
GW
Revision: 2006 July 2007 FX35/FX45
6. CHECK REAR WINDOW DEFOGGER RELAY OUTPUT SIGNAL
1. Connect IPDM E/R connector and rear window defogger relay.
2. Turn ignition switch ON.
3. Check voltage between IPDM E/R connector E9 terminal 52 and ground.
OK or NG
OK >> Check condition of harness and connector.
NG >> Replace IPDM E/R.
Check Rear Window Defogger Circuit NIS001SE
1. CHECK POWER SUPPLY CIRCUIT 1
1. Turn ignition switch OFF.
2. Disconnect rear window defogger connector.
3. Turn ignition switch ON.
4. Check voltage between rear window defogger connector and ground.
OK or NG
OK >> GO TO 2.
NG >> GO TO 3.
2. CHECK GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Check continuity between rear window defogger connector D114 terminal 2 and ground.
OK or NG
OK >> Check filament. Refer to GW-87, "Check Filament"

If filament is OK, check condition of harness and con-
nector.

If filament is NG, repair filament.
NG >> Repair or replace harness. 52 (G) – Ground : Battery voltage
PIIA6210E
Connector
Terminal (Wire color)
Condition Voltage (V)
(Approx.)
(+) (–)
D104 1(W) Ground Rear window defogger
switch ON. Battery voltage
Rear window defogger
switch OFF. 0
PIIA9347E
2 (B)
− Ground : Continuity should exist.
PIIA9348E

GW-82
REAR WINDOW DEFOGGER
Revision: 2006 July 2007 FX35/FX45
3. CHECK REAR WINDOW DEFOGGER RELAY CIRCUIT
1. Turn ignition switch OFF.
2. Remove rear window defogger relay.
3. Check continuity between rear window defogger relay connector E13 terminal 5, 7 and rear window defogger connector D104 ter-
minal 1.
OK or NG
OK >> Check condition of harness and connector.
NG >> Repair or replace harness.
Check Door Mirror Defogger Power Supply Circuit NIS001SF
1. CHECK FUSE

Check 15A fuse [No.8, located in fuse block (J/B)]
NOTE:
Refer to GW-67, "
Component Parts and Harness Connector Location" .
OK or NG
OK >> GO TO 2.
NG >> If fuse is blown out, be sure to eliminate cause of malfunction before installing new fuse. Refer to
PG-3, "
POWER SUPPLY ROUTING CIRCUIT" .
2. CHECK POWER SUPPLY CIRCUIT 1
1. Turn ignition switch ON.
2. Check voltage between fuse block (J/B) connector and ground.
OK or NG
OK >> GO TO 3.
NG >> Repair or replace harness.
3. CHECK POWER SUPPLY CIRCUIT 2
Check voltage between fuse block (J/B) connector and ground.
OK or NG
OK >> GO TO 4.
NG >> Replace fuse block (J/B). 5 (B) – 1 (W) : Continuity should exist.
7 (B) – 1 (W) : Continuity should exist.
PIIA9349E
Connector Terminal (Wire color)
Condition Voltage (V)
(Approx.)
(+) (–)
E201 2C (B) Ground Rear window defogger
switch ON Battery voltage
Rear window defogger
switch OFF 0
PIIA2388E
Connector Terminal (Wire color)
Condition Voltage (V)
(Approx.)
(+) (–)
M2 5B (L) Ground Rear window defogger
switch ON Battery voltage
Rear window defogger
switch OFF 0
PIIA2386E

REAR WINDOW DEFOGGER GW-83
C
D E
F
G H
J
K L
M A
B
GW
Revision: 2006 July 2007 FX35/FX45
4. CHECK DOOR MIRROR CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect fuse block (J/B) and door mirror connector.
3. Check continuity between fuse block (J/B) connector and door mirror connector.
OK or NG
OK >> GO TO 5.
NG >> Repair or replace harness.
5. CHECK GROUND CIRCUIT
Check continuity between each door mirror connector and ground.
OK or NG
OK >> GO TO 6.
NG >> Repair or replace harness.
6. CHECK DOOR MIRROR DEFOGGER
1. Connect door mirror connector.
2. Check continuity between each door mirror connector.
OK or NG
OK >> Check condition of harness and connector.
NG >> Replace malfunctioning door mirror.
AB
Continuity
Fuse block (J/B)
connector TerminalDoor mirror
connector Te r m i n a l
M2 5B (L) D2 (driver side)
D32 (passenger side) 4(L) Yes
PIIB8569E
Door mirror
connector terminal
Ground Continuity
D2 (driver side)
D32 (passenger side) 3(B) Yes
PIIB8570E
Door mirror
connector terminal Terminal Continuity
D2 (driver side)
D32 (passenger side) 3(B) 4(L) Yes
PIIB8571E

GW-84
REAR WINDOW DEFOGGER
Revision: 2006 July 2007 FX35/FX45
Check Driver Side Door Mirror Defogger Circuit NIS001SG
1. CHECK POWER SUPPLY CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect door mirror (driver side) connector.
3. Turn ignition switch ON.
4. Check voltage between door mirror (driver side) connector and ground.
OK or NG
OK >> GO TO 2.
NG >> Repair or replace harness.
2. CHECK GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Check continuity between door mirror (driver side) connector and ground.
OK or NG
OK >> GO TO 3.
NG >> Repair or replace harness.
3. CHECK DOOR MIRROR DEFOGGER
1. Connector door mirror connector.
2. Check continuity between each door mirror connector.
OK or NG
OK >> Check condition of harness and connector.
NG >> Replace door mirror (driver side).
Connector Terminal (Wire color)
Condition Voltage (V)
(Approx.)
(+) (–)
D2 4 (L) Ground Rear window defogger
switch ON Battery voltage
Rear window defogger
switch OFF 0
PIIB8572E
Door mirror
connector terminal
Ground Continuity
D2 (driver side)
D32 (passenger side) 3(B) Yes
PIIB8570E
Door mirror
connector terminal Terminal Continuity
D2 (driver side)
D32 (passenger side) 3(B) 4(L) Yes
PIIB8571E

REAR WINDOW DEFOGGER GW-85
C
D E
F
G H
J
K L
M A
B
GW
Revision: 2006 July 2007 FX35/FX45
Check Passenger Side Door Mirror Defogger Circuit NIS001SH
1. CHECK POWER SUPPLY CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect door mirror (passenger side) connector.
3. Turn ignition switch ON.
4. Check voltage between door mirror (passenger side) connector and ground.
OK or NG
OK >> GO TO 2.
NG >> Repair or replace harness.
2. CHECK GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Check continuity between door mirror (passenger side) connec- tor and ground.
OK or NG
OK >> GO TO 3.
NG >> Repair or replace harness.
3. CHECK DOOR MIRROR DEFOGGER
1. Connector door mirror connector.
2. Check continuity between each door mirror connector.
OK or NG
OK >> Check condition of harness and connector.
NG >> Replace door mirror (passenger side).
Check Rear Window Defogger Signal NIS001SI
1. CHECK REAR WINDOW DEFOGGER SWITCH LAMP
A/C and AV switch self-diagnosis is performed. Refer to AV- 3 5 , "
A/C and AV Switch Self-Diagnosis Function"
Does rear window defogger switch light?
YES >> GO TO 2.
NO >> Replace A/C and AV switch.
Connector Terminal (Wire color)
Condition Voltage (V)
(Approx.)
(+) (–)
D32 4 (L) Ground Rear window defogger
switch ON Battery voltage
Rear window defogger
switch OFF 0
PIIB8572E
Door mirror
connector terminal
Ground Continuity
D2 (driver side)
D32 (passenger side) 3(B) Yes
PIIB8570E
Door mirror
connector terminal Terminal Continuity
D2 (driver side)
D32 (passenger side) 3(B) 4(L) Yes
PIIB8571E

IDX-4
ALPHABETICAL INDEX
Electrical units location ...................................... PG-67
Electronic ignition (EI) system ............. EC-32, EC-694
Engine control circuit diagram ......................... EC-107
Engine control component parts location ......... EC-100
Engine control module (ECM) .......... EC-480, EC-1148
Engine control system diagram ........... EC-29, EC-691
Engine coolant temperature sensor (ECTS) ... EC-209,
EC-221
, EC-880, EC-893
Engine coolant(VK45DE) .................................. CO-38
Engine coolant(VQ35DE) ................................. CO-11
Engine fail-safe system ...................................... EC-95
Engine oil filter replacement ............................. MA-26
Engine oil filter replacement(VQ35DE) ............. MA-19
Engine oil precautions .......................................... GI-8
Engine oil replacement(VQ35DE) ..................... MA-18
Engine oil(VK45DE) ........................................... LU-25
Engine oil(VQ35DE) ............................................ LU-7
Engine removal(VK45DE) ............................... EM-243
Engine removal(VQ35DE) .............................. EM-113
Engine room cover(VK45DE) ......................... EM-173
ETC1 - Wiring diagram .................... EC-564, EC-1245
ETC2 - Wiring diagram .................... EC-559, EC-1240
ETC3 - Wiring diagram .................... EC-570, EC-1252
EVAP canister ...................................... EC-41, EC-703
EVAP canister purge volume control solenoid valve ....
EC-396
, EC-404, EC-1065, EC-1073
EVAP canister vent control valve ...... EC-411, EC-418,
EC-1080
, EC-1087
EVAP control system (small leak) diagnosis .. EC-387,
EC-449
, EC-1056, EC-1118
EVAP control system pressure sensor ........... EC-424,
EC-427
, EC-433, EC-1093, EC-1096, EC-1102
EVAP control system purge flow monitoring diagnosis
EC-382
, EC-1051
EVAP vapor lines inspection ................. MA-21, MA-28
Evaporative emission (EVAP) system . EC-38, EC-700
Evaporator ..................................................... ATC-154
Exhaust manifold(VK45DE) ............................ EM-183
Exhaust manifold(VQ35DE) .............................. EM-26
Exhaust system ................................................... EX-3
Exhaust system inspection ..................... EX-3, MA-29
Expansion valve ............................................. ATC-155
F
F/PUMP - Wiring diagram ................ EC-637
, EC-1319
Final drive pre-inspection .................. FFD-20, RFD-19
Final drive removal and installation .. FFD-13, FFD-15,
RFD-16
Floor trim ............................................................. EI-41
Flow charts ......................................................... GI-28
Fluid temperature sensor (A/T) ........................ AT-134
Fluorescent leak detector .............................. ATC-156
Freeze frame data ............................... EC-59, EC-721
Front axle ................................ FAX-4, FAX-10, RAX-5
Front brake solenoid valve ................. AT-150, AT-152
Front bumper ...................................................... EI-14
Front door ............................. BL-148, BL-152, GW-58
Front passenger air bag .................................. SRS-46
Front seat belt ...................................................... SB-4
Front seat belt pre-tensioner ..... SB-2, SRS-3, SRS-52
Front suspension .............................................. FSU-6
FTS - Wiring diagram ....................................... AT-135
FTTS - Wiring diagram .... EC-329, EC-334, EC-1000,
EC-1005
Fuel cut control (at no load high engine speed) EC-33,
EC-695
Fuel filter replacement ......................................... FL-4
Fuel gauge ............................................................ DI-5
Fuel injection system (Bank 1) ......... EC-304, EC-316,
EC-976
, EC-987
Fuel injection system (Bank 2) ......... EC-304, EC-316,
EC-976
, EC-987
Fuel injector ..................................................... EC-629
Fuel injector and fuel tube(VK45DE) .............. EM-194
Fuel injector and fuel tube(VQ35DE) ................ EM-45
Fuel level sensor EC-459, EC-461, EC-463, EC-1127,
EC-1129
, EC-1131
Fuel line inspection .................................. FL-3, MA-25
Fuel line inspection(VQ35DE) .......................... MA-17
Fuel precautions .......................................... GI-6, GI-7
Fuel pressure check ........................... EC-85, EC-747
Fuel pressure release ......................... EC-85, EC-747
Fuel pump ....................................... EC-636, EC-1318
Fuel pump and gauge .......................................... FL-4
Fuel system ......................................................... FL-3
Fuel tank ............................................................ FL-10
Fuel tank temperature sensor .......... EC-327, EC-333,
EC-998
, EC-1004
Fuel tank vacuum relief valve ............. EC-41, EC-703
FUELB1 - Wiring diagram .. EC-306, EC-318, EC-978,
EC-989
FUELB2 - Wiring diagram .. EC-308, EC-320, EC-980,
EC-991
Fuse .................................................................. PG-16
Fuse and fusible link box .................................. PG-81
Fusible link ........................................................ PG-16
G
Gauges ................................................................. DI-5
Generic scan tool (GST) .................................. EC-129
Glass ...................................... GW-11, GW-58, GW-62
Grille - See Exterior ............................................ EI-22
Ground distribution ........................................... PG-29
H
Harness connector ............................................ PG-71
Harness layout .................................................. PG-43
Headlining - See Roof trim .................................. EI-43
Heated oxygen sensor 2 (bank 1) .... EC-269, EC-280,
EC-293
, EC-941, EC-952, EC-965
Heated oxygen sensor 2 (bank 2) .... EC-269, EC-280,
EC-293
, EC-941, EC-952, EC-965
Heated oxygen sensor 2 heater (bank 1) ....... EC-172,
EC-844
Heated oxygen sensor 2 heater (bank 2) ....... EC-172,

IDX-5
A
C
D E
F
G H
I
J
K L
B
IDX
ALPHABETICAL INDEX
EC-844
Heated seat .......................................................
SE-94
Heater and cooling unit (Heater core) ........... ATC-125
HFC134a (R134a) system precaution ............... ATC-6
HFC134a (R134a) system service procedure ATC-137
HFC134a (R134a) system service tools .......... ATC-18
HFC134a system service equipment precaution ..........
ATC-13
High and low reverse clutch solenoid valve .... AT-158,
AT-160
Hood ................................................................... BL-13
How to erase DTC for OBD system ..... EC-58, EC-728
HSEAT - Wiring diagram ................................... SE-95
I
IATS - Wiring diagram ....................... EC-206
, EC-877
ICC - Wiring diagram ....................................... ACS-21
ICC/BS - Wiring diagram ................. EC-532, EC-1208
ICC/SW - Wiring diagram ................ EC-517, EC-1193
ICCBOF - Wiring diagram ................ EC-643, EC-1325
Idle air volume learning ....................... EC-83, EC-745
Idle speed .............................. EC-81, EC-738, EC-743
Idle speed control (ISC) .... EC-467, EC-469, EC-1135,
EC-1137
Ignition coil ....................................... EC-650, EC-1332
Ignition coil(VK45DE) ...................................... EM-191
Ignition coil(VQ35DE) ........................................ EM-42
Ignition control system ..................... EC-650, EC-1332
Ignition timing ........................ EC-81, EC-738, EC-743
IGNSYS - Wiring diagram ................ EC-651, EC-1333
In vehicle sensor ........................... ATC-106, ATC-117
INF/D - Wring diagram ....................................... AV-57
INJECT - Wiring diagram ................. EC-630, EC-1312
Injector ........................................................... EC-1311
Input clutch solenoid valve ................. AT-146, AT-148
Instrument panel .................................................. IP-10
Intake air temperature sensor ........... EC-204, EC-224,
EC-875
, EC-896
Intake door control linkage adjustment ............ ATC-76
Intake door motor ........................... ATC-74, ATC-123
Intake manifold collector(VQ35DE) ................... EM-19
Intake manifold(VK45DE) ................................ EM-179
Intake manifold(VQ35DE) .................................. EM-24
Intake sensor ................................ ATC-112, ATC-119
Intake valve timing control (Bank 1) .. EC-160, EC-825
Intake valve timing control (Bank 2) .. EC-160, EC-825
Intake valve timing control position sensor (Bank 1) ....
EC-1161
Intake valve timing control position sensor (Bank 2) ....
EC-1161
Intake valve timing control solenoid valve (Bank 1) ......
EC-180
, EC-852
Intake valve timing control solenoid valve (Bank 2) ......
EC-180
, EC-852
Integrated homelink transmitter ........................ BL-226
Intelligent cruise control (ICC) system ............... ACS-6
Interior ................................................................. EI-38
IPDM (Intelligent power distribution module engine room) .................................................................
PG-17
IVCB1 - Wiring diagram ..................... EC-181, EC-853
IVCB2 - Wiring diagram ..................... EC-183, EC-855
IVCSB1 - Wiring diagram ............................... EC-1163
IVCSB2 - Wiring diagram ............................... EC-1165
IVIS (Infiniti vehicle immobilizer system) precautions ...
GI-3
IVTB1 - Wiring diagram ................................... EC-828
IVTB2 - Wiring diagram ................................... EC-830
K
Knock sensor (KS) ........................... EC-355
, EC-1026
KS - Wiring diagram ......................... EC-356, EC-1027
L
LAN system circuit ........................................... ATC-64
Lane Departure Warning System ....................... DI-77
Laser beam aiming adjustment ....................... ACS-14
Latch (lower anchors and tether for children) system ...
SB-10
LDW .................................................................... DI-77
LDW - Wiring Diagram ........................................ DI-89
Line pressure solenoid valve ........................... AT-129
Line pressure test (A/T) ..................................... AT-54
Liquid gasket application ......................... EM-6, LU-21
Liquid gasket application(VQ35DE) ........... LU-3, CO-3
Location of electrical units ................................. PG-67
Low coast brake solenoid valve ......... AT-162, AT-164
Lubricant (R134a) A/C ..................................... ATC-27
Lubrication circuit (engine)(VK45DE) ................ LU-23
Lubrication circuit (engine)(VQ35DE) .................. LU-5
Lubrication oil A/C .......................................... ATC-160
M
M/ANT - Wiring diagram .................................... AV-49
MAFS - Wiring diagram ..... EC-190, EC-198, EC-862,
EC-870
Magnet clutch ................................. ATC-82, ATC-142
MAIN - Wiring diagram ........ EC-148, EC-813, AT-179
Maintenance (engine)(VQ35DE) ...................... MA-14
Major overhaul (Final drive) .............. FFD-17, RFD-18
Major overhaul (Transfer) .................................. TF-45
Malfunction indicator lamp (MIL) .......... EC-67, EC-730
Mass air flow sensor (MAFS) ............ EC-187, EC-196,
EC-859
, EC-868
Meter ..................................................................... DI-5
METER - Wiring diagram .................................... DI-12
MIL data link connectors circuit ....... EC-673, EC-1364
MIL/DL - Wiring diagram .................. EC-673, EC-1364
Mirror, door ....................................................... GW-98
Mirror, out side .................................................. GW-98
Misfire .............................................. EC-345, EC-1016
MMSW - Wiring diagram .................................. AT-167
Mode door control linkage adjustment ............. ATC-70
Mode door motor ............................ ATC-68, ATC-130
Molding - See Exterior ................... EI-25, EI-30, EI-33