2007 HUMMER H3 key

How to Check Power Steering Fluid
1. Turn the key off and let the engine
compartment cool down.
2. Wipe the cap and the top of the reservoir clean.
3. Unscrew the cap and wipe the dipstick with a
clean rag.
4. Replace the cap and completely tighten it.
5. Then remove the cap again and look at
the uid level on the dipstick.
The level should be between the ADD and FULL
marks. If necessary, add only enough uid to
bring the level up to the proper range.
What to Use
To determine what kind of uid to use, see
Recommended Fluids and Lubricants on page 440.
Always use the proper uid. Failure to use the
proper uid can cause leaks and damage hoses
and seals.
Windshield Washer Fluid
What to Use
When you need windshield washer uid, be sure
to read the manufacturer’s instructions before
use. If you will be operating your vehicle in an area
where the temperature may fall below freezing,
use a uid that has sufficient protection against
freezing.
Adding Washer Fluid
Open the cap with the
washer symbol on it.
Add washer uid
until the tank is full. See
Engine Compartment
Overview on page 322
for reservoir location.
346

5. Remove the valve cap from the valve cap
stem. Activate the TPMS sensor by
increasing or decreasing the tire’s air pressure
for 10 seconds, then stop and listen for a
single horn chirp. The single horn chirp should
sound within 15 seconds, conrming that
the sensor identication code has been
matched to this tire and wheel position. If you
do not hear the conrming single horn
chirp, you will need to start over with step
number one. To let air-pressure out of a tire
you can use the pointed end of the valve cap,
a pencil-style air pressure gage, or a key.
6. Proceed to the passenger’s side front tire,
and repeat the procedure in Step 5.
7. Proceed to the passenger’s side rear tire,
and repeat the procedure in Step 5.8. Proceed to the driver’s side rear tire, and
repeat the procedure in Step 5.
9. After hearing the conrming horn chirp
for the left rear tire, check to see if
the TPMS warning light is still ashing.
If it is, turn the ignition switch to LOCK.
If the TPMS warning light is not ashing,
the ve minute time limit has passed and
you will need to start the process
over beginning with Step 1.
10. Set all four tires to the recommended air
pressure level as indicated on the Tire
and Loading Information label.
11. Put the valve caps back on the valve stems.
380

2. Remove the center
cap, if equipped, by
placing the at
end of the wheel
wrench in the slot
on the wheel
and gently pry the
center cap out.3. Use the wheel
wrench to remove
the wheel nuts
securing the
spare tire.
If your vehicle has locking lug nuts, the key is
supplied in the tool bag. Use the key along
with the wheel wrench to remove the
wheel nuts from the tire.
4. Pull off and gently lower the spare tire to the
ground. Set it next to the at tire.
In order to remove the spare tire, you may
need someone to assist you.
395

Removing the Flat Tire and
Installing the Spare Tire
1. Remove the center
cap by placing the
at end of the wheel
wrench in the slot
on the wheel
and gently pry the
center cap out.2. Turn the wheel
wrench
counterclockwise
to loosen the
wheel nuts.
Do not remove
them yet.
If your vehicle has locking lug nuts, the key is
supplied in the tool bag. Use the key along
with the wheel wrench to remove the
wheel nuts from the tire.
You will now need to jack up the vehicle using
the following instructions.
396

(c)Visually inspect hoses and have them replaced
if they are cracked, swollen, or deteriorated.
Inspect all pipes, ttings, and clamps; replace with
genuine GM parts as needed. To help ensure
proper operation, a pressure test of the cooling
system and pressure cap and cleaning the outside
of the radiator and air conditioning condenser is
recommended at least once a year.
(d)Visually inspect wiper blades for wear or
cracking. Replace wiper blades that appear worn
or damaged or that streak or miss areas of
the windshield.
(e)Make sure the safety belt reminder light and all
your belts, buckles, latch plates, retractors, and
anchorages are working properly. Look for any
other loose or damaged safety belt system parts.
If you see anything that might keep a safety belt
system from doing its job, have it repaired. Have
any torn or frayed safety belts replaced. Also look
for any opened or broken airbag coverings, and
have them repaired or replaced. The airbag system
does not need regular maintenance.(f)Lubricate all key lock cylinders, hood latch
assembly, secondary latch, pivots, spring anchor,
release pawl, rear compartment hinges, outer
swing-gate handle pivot points, rear door detent
link, roller mechanism, swing-gate handle
pivot points, latch bolt, fuel door hinge, locks, and
folding seat hardware. More frequent lubrication
may be required when exposed to a corrosive
environment. Applying silicone grease on
weatherstrips with a clean cloth will make them
last longer, seal better, and not stick or squeak.
(g)Check vent hose at transfer case for kinks and
proper installation.
(h)Change automatic transmission uid and lter
if the vehicle is mainly driven under one or
more of these conditions:
In heavy city traffic where the outside
temperature regularly reaches 90°F (32°C)
or higher.
In hilly or mountainous terrain.
When doing frequent trailer towing.
Uses such as found in taxi, police, or
delivery service.
434

Automatic Transmission Shift Lock
Control System Check
{CAUTION:
When you are doing this inspection, the
vehicle could move suddenly. If the vehicle
moves, you or others could be injured.
1. Before you start, be sure you have enough
room around the vehicle. It should be parked
on a level surface.
2. Firmly apply the parking brake. SeeParking
Brake on page 116.
Be ready to apply the regular brake
immediately if the vehicle begins to move.3. With the engine off, turn the ignition to ON,
but do not start the engine. Without applying
the regular brake, try to move the shift
lever out of PARK (P) with normal effort. If the
shift lever moves out of PARK (P), contact
your GM Goodwrench
®dealer for service.
Ignition Transmission Lock Check
While parked, and with the parking brake set, try to
turn the ignition to LOCK in each shift lever position.
With an automatic transmission, the ignition
should turn to LOCK only when the shift lever is
in PARK (P). The ignition key should come out
only in LOCK.
With a manual transmission, the ignition key
should come out only in LOCK.
Contact your GM Goodwrench
®dealer if service is
required.
438

Recommended Fluids and
Lubricants
Fluids and lubricants identied below by name,
part number, or specication may be obtained
from your dealer.
Usage Fluid/Lubricant
Engine OilEngine oil which meets
GM Standard GM6094M and
displays the American Petroleum
Institute Certied for Gasoline
Engines starburst symbol.
GM Goodwrench
®oil meets all
the requirements for your vehicle.
To determine the proper viscosity
for your vehicle’s engine, see
Engine Oil on page 323.
Engine Coolant50/50 mixture of clean, drinkable
water and use only DEX-COOL
®
Coolant. SeeEngine Coolant
on page 335.
Usage Fluid/Lubricant
Hydraulic Brake
SystemDelco
®Supreme 11 Brake Fluid or
equivalent DOT-3 brake uid.
Windshield
WasherGM Optikleen
®Washer Solvent.
Power Steering
SystemGM Power Steering Fluid
(GM Part No. U.S. 89021184,
in Canada 89021186).
Automatic
TransmissionDEXRON
®-VI Automatic
Transmission Fluid.
Manual
TransmissionManual Transmission Fluid
(GM Part No. U.S. 89021806,
in Canada 89021807).
Hydraulic
Clutch SystemHydraulic Clutch Fluid
(GM Part No. U.S. 12345347,
in Canada 10953517) or equivalent
DOT-3 brake uid.
Key Lock
CylindersMulti-Purpose Lubricant, Superlube
(GM Part No. U.S. 12346241,
in Canada 10953474).
440

Roadside Assistance Program
As the owner of a new HUMMER vehicle, you are
automatically enrolled in the HUMMER Roadside
Assistance program. This value-added service
is intended to provide peace of mind as you drive
in the city or travel the open road. In the U.S.,
call1-866-HUMMER6 (486-6376)and in Canada,
call1-800-268-680024 hours a day, 365 days
a year to speak with a HUMMER Roadside
Assistance Representative.
The following services are provided in the U.S.
during the Bumper-to-Bumper warranty period and
the Base Warranty period of the New Vehicle
Limited Warranty in Canada up to a maximum
coverage of $100.
Fuel Delivery:Delivery of enough fuel ($5 in
the U.S. and 10 litres in Canada maximum)
for the customer to get to the nearest service
station.
Service to provide diesel may be restricted.
For safety reasons, propane and other
alternate fuels will not be provided.
Lock-out Service (identication required):
Lock-out service will be covered at no charge
if you are unable to gain entry into your
vehicle. If your vehicle will not start, Roadside
Assistance will arrange to have your vehicle
towed to the nearest authorized dealership.
In the U.S., a replacement key will be
delivered within 10 miles.
Emergency Tow from a Public Roadway
or Highway:Tow to the nearest dealership
for warranty service or in the event of a
vehicle-disabling accident.
Flat Tire Change:Installation of your vehicle’s
spare tire in good condition will be covered at
no charge. The customer is responsible for
the repair or replacement of the tire if not
covered by a warrantable failure.
Jump Start:No-start occurrences which
require a battery jump start will be covered
at no charge.
Dealer Locator Service:Directions to the
nearest dealer.
454