2007 HONDA PILOT speed

If you get stuck, engage the VTM-4
Lock (see page ). Carefully try to
go in the direction (f orward or
reverse) that you think will get you
unstuck. Do not spin the tires at high
speeds. It will not help you get out
and may cause damage to the
transmission or VTM-4 system.
If you are still unable to f ree yourself ,
your vehicle is equipped with f ront
and rear tow hooks designed f or this
purpose.
Bef ore driving through water, stop,
get out if necessary, and make sure
that:
The water is not deep enough to
cover your wheel hubs, axles, or
exhaust pipe. You could stall and
not be able to restart your engine.
The water can also damage
important vehicle components.
The banks are sloped so you can
drive out.
The water is not f lowing too f ast.
Deep rushing water can sweep you
downstream. Even very shallow
rushingwatercanwashthe
ground f rom under your tires and
cause you to lose traction and
possibly roll over.
The banks and surf ace under the
water provide good traction. The
water may hide hazards such as
rocks, holes, or mud. If you decide it is saf e to drive
through water, choose a suitable
speed and engage the VTM-4 Lock.
Proceed without shif ting or changing
speeds, and do not stop the vehicle
or shut of f the engine.
After driving through water, test
your brakes. If they got wet, gently
‘‘pump’’ them while driving slowly
until they operate normally.
If the water is deeper than the wheel
hubs, some additional service may
be required. This service is not
covered by your warranties.
Use a nylon strap to attach your
vehicle to the recovery vehicle, and
caref ully take out the slack in the
strap. Once the strap is tight, the
recovery vehicle should apply f orce.
Remember that the recovery vehicle
needs good traction to avoid
becoming stuck, too.204
If You Get Stuck
Crossing a Stream
Of f -Highway Driving Guidelines
224

ÌÌ
µµ
Ì
Maintenance Minder
235
Maintenance Sub Items
Rotate tires
Replace air cleaner element
Replace dust and pollen filter
Inspect drive belt
Replace transmission and transfer fluid
Replace spark plugs
Replace timing belt and inspect water pump
Inspect valve clearance
Replace engine coolant
ReplaceVTM-4reardifferentialfluid
2
: See
information on maintenance and emissions warranty on page .
Inspect idle speed every 160,000 miles (256,000 km).
If the message ‘‘SERVICE’’ does not appear more than 12 months after the
display is reset, change the engine oil every year.
Independent of the maintenance messages in the information display,
replace the brake fluid every 3 years.
Adjust the valves during services A, B, 1, 2, or 3 if they are noisy.
NOTE: 1:
234
Maintenance Main Items
Replace engine oil
Replace engine oil and oil filter
Inspect front and rear brakes
Check parking brake adjustment
Inspect these items: Tie rod ends, steering gear box, and boots
Suspension components
Driveshaft boots
Brake hoses and lines (including ABS)
All fluid levels and condition of fluids
Exhaust system
Fuel lines and connections
A
B
1
2
3
4
5
61
1
If you drive in dusty conditions, replace every 15,000 miles
(24,000 km).
If you drive primarily in urban areas that have high concentrations
of soot in the air from industry and from diesel-powered vehicles,
replace every 15,000 miles (24,000 km).
Driving in mountainous areas at very low vehicle speeds or trailer
towing results in higher transmission and transfer fluid
temperatures. This requires transmission and transfer fluid changes
more frequently than recommended by the Maintenance Minder. If
you regularly drive your vehicle under these conditions, have the
transmission and transfer fluid changed every 30,000 miles
(48,000 km).
If you drive regularly in very high temperatures (over 110°F, 43°C),
in very low temperatures (under 20°F, 29°C), or towing a trailer,
replace every 60,000 miles (U.S.) /100,000 km (Canada).
Driving in mountainous areas at very low vehicle speeds or trailer
towing results in higher level of mechanical (shear) stress to fluid
This requires differential fluid changes more frequently than
recommended by the Maintenance Minder. If you regularly drive
your vehicle under these conditions, have the differential fluid
changed at 7,500 miles (12,000 km), then every 15,000 miles
(24,000 km).
Symbol
Symbol
Maintenance Minder
2:4WD

Wheels:
Tires:
See page for info rmation about
DOT Tire Quality Grading, and page
f or tire size and labeling
inf ormation.
Replace your tires with radial tires of
the same size, load range, speed
rating, and maximum cold tire
pressure rating (as shown on the
tire’s side wall).
Mixing radial and bias-ply tires on
your vehicle can reduce braking
ability, traction, and steering
accuracy. Using tires of a dif f erent
size or construction can cause the
anti-lock brake and the vehicle
stability assist systems to work
inconsistently.
It is best to replace all f our tires at
thesametime.If thatisnotpossible
or necessary, replace the two f ront
tires or two rear tires as a pair.
Replacing just one tire can seriously
af f ect your vehicle’s handling.
If you ever replace a wheel, make
sure that the wheel’s specif ications
match those of the original wheels.
Replacement wheels are available at
your dealer.
To help increase tire lif e and
distribute wear more evenly, rotate
the tires according to the
maintenance messages displayed on
the information display.
Move the tires to the positions
shown in the illustration each time
they are rotated. If you purchase
directional tires, rotate only f ront-to-
back.
290
291
Tires
Wheel and T ire Specif ications
Replacing T ires and Wheels
Tire Rotation
260
(For Non-directional
Tires and Wheels) (For Directional
Tires and Wheels)
Front
Front
16x61/2JJ
P235/70R16 104S Installing improper tires on your
vehicle can affect handling and
stability. This can cause a crash
in which you can be seriously
hurt or killed.
Always use the size and type of
tires recommended in this
owner’s manual.

´When installing cables, f ollow the
manuf acturer’s instructions, and
mount them as tight as you can.
Make sure they are not contacting
the brake lines or suspension. Drive
slowly with them installed. If you
hear them coming into contact with
the body or chassis, stop and
investigate. Remove them as soon as
youbegindrivingonclearedroads. Because your vehicle has limited tire
clearance, mount only SAE Class ‘‘S’’
cable-type traction devices, with
rubber chain tensioners, on the f ront
tires. Use traction devices only when
required by driving conditions or
local laws. Make sure they are the
correct size f or your tires. Metal link-
type ‘‘chains’’ should not be used.
Tires marked ‘‘M S’’ or ‘‘All
Season’’ on the sidewall have an all-
weather tread design suitable for
most winter driving conditions.
For the best perf ormance in snowy
or icy conditions, you should install
snow tires or tire chains. They may
be required by local laws under
certain conditions.
If you mount snow tires on your
vehicle, make sure they are radial
tires of the same size and load range
as original tires. Mount snow tires on
all f our wheels. The traction
provided by snow tires on dry roads
maybelowerthanyouroriginaltires.
Check with the tire dealer f or
maximum speed recommendations.
Tires
Tire Chains
Winter Driving
Snow T ires
Maint enance
261
Traction devices that are the wrong
size or improperly installed can
damage your vehicle’s brake lines,
suspension, body, and wheels. Stop
driving if they are hitting any part of
the vehicle.

Diagnosing why the engine won’t
start falls into two areas, depending
on what you hear when you turn the
ignition switch to the START (III)
position: You hear nothing, or almost
nothing. The engine’s starter
motor does not operate at all, or
operates very slowly.
You can hear the starter motor
operating normally, or the starter
motor sounds like it is spinning
faster than normal, but the engine
does not start up and run.
Wh en you turn the ignition switch to
the START (III) position, you do not
hear the normal noise of the engine
trying to start. You may hear a
clicking sound, a series of clicks, or
nothing at all. Check
the transmission interlock.
The transmission must be in Park
or neutral or the starter will not
operate.
Are you using the proper starting
procedure? Refer to
on page .
In
this case, the starter motor’s
speed sounds normal, or even faster
than normal, when you turn the
ignition switch to the START (III)
position, but the engine does not run.
Check these things: Turn
the ignition switch to the
START (III) position. If the
headlights do not dim, check the
condition of the fuses. If the fuses
areOK,thereisprobably
something wrong with the
electrical circuit for the ignition
switch or starter motor. You will
need a qualified technician to
determine the problem. See
on page .
Turn
the ignition switch to the ON
(II) position. Turn on the
headlights, and check their
brightness. If the headlights are
very dim or do not come on at all,
the battery is discharged. See
on page . If
the headlights dim noticeably or
go out when you try to start the
engine, either the battery is
discharged or the connections are
co rroded. Check the condition of
the battery and terminal
connections (see page ). You
canthentryjump startingthe
vehicle from a booster battery
(see page ).
272
279 199262
272
CONT INUED
Nothing Happens or the Starter
Motor Operates Very Slowly Starting the
Engine
T he Starter Operates Normally
Emergency T owing Jump Starting
If theEngineWon’tStart
T aking Care of t he Unexpect ed
271

µµµ
µ
µ
µ
µ
µ
Warning: The temperature grade f or
this tire is established f or a tire that
is properly inf lated and not
overloaded. Excessive speed,
underinf lation, or excessive loading,
either separately or in combination,
can cause heat buildup and possible
tire f ailure.
The tires that came on your vehicle
have a number of markings. Those
you should be aware of are described
below.
Whenever tires are replaced, they
should be replaced with tires of the
same size. Following is an example
of tire size with an explanation of
what each component means.
Speed symbol (an
alphabetical code indicating
the maximum speed rating).Tire construction code (R
indicates radial).
Load index (a numerical code
associated with the maximum
load the tire can carry). Rim diameter in inches. Aspect ratio (the tire’s section
height as a percentage of its
width). Tire width in millimeters. Vehicletype(Pindicates
passenger vehicle).
The temperature grades are A (the
highest), B, and C, representing the
tire’s resistance to the generation of
heat and its ability to dissipate heat
when tested under controlled
conditions on a specif ied indoor
laboratory test wheel. Sustained high
temperature can cause the material
of the tire to degenerate and reduce
tire life, and excessive temperature
can lead to sudden tire f ailure. The
grade C corresponds to a level of
perf ormance which all passenger car
tires must meet under the Federal
Motor Vehicle Saf ety Standard No.
109. Grades B and A represent
higher levels of perf ormance on the
laboratory test wheel than the
minimum required by law. P
16 R 235
70
104
S
Temperature A,B,C
Tire Labeling
DOT Tire Quality Grading (U.S. Vehicles), Tire L abeling
Tire Size
Technical Inf ormation
291
P235/70R16 104S

If you take your vehicle f or a state
emissions test shortly af ter the
battery has been disconnected or
gone dead, it may not pass the test.
This is because of certain ‘‘readiness
codes’’ that must be set in the on-
board diagnostics f or the emissions
systems. These codes are erased
when the battery is disconnected,
and set again only after several days
of driving under a variety of
conditions.
If the testing f acility determines that
the readiness codes are not set, you
will be requested to return at a later
date to complete the test. If you must
get the vehicle retested within the
next two or three days, you can
condition the vehicle f or retesting by
doing the f ollowing.Make sure the gas tank is nearly,
but not completely, f ull (around
3/4).
Without touching the accelerator
pedal, start the engine, and let it
idle f or 20 seconds.
Keep the vehicle in Park. Increase
the engine speed to 2,000 rpm, and
hold it there until the temperature
gauge rises to at least 1/4 of the
scale (about 3 minutes).
Select a nearby lightly traveled
major highway where you can
maintain a speed of 50 to 60 mph
(80to97km/h)foratleast20
minutes. Drive on the highway in
D. Do not use the cruise control.
When traffic allows, drive for 90
seconds without moving the
accelerator pedal. (Vehicle speed
may vary slightly; this is okay.) If
you cannot do this f or a
continuous 90 seconds because of
traf f ic conditions, drive f or at least
30 seconds, then repeat it two
more times (for a total of 90
seconds).
Make sure the vehicle has been
parked with the engine of f f or 6
hours or more.
Make sure the ambient
temperature is between 40° and
95°F.
T esting of Readiness Codes
State Emissions T esting
298

CONT INUED
...
Accessories and Modif ications .191
ACCESSORY (Ignition Key
.......................................
Position) .81
............
Accessory Power Sockets .101
...........................
AC Power Outlet .102
....................
Additives, Engine Oil .239
...............
AdvancedAirbagSystem .30
.............................
Airbag (SRS) . 11, 25
..........
Airbag System Components .25
..............
Air Conditioning System .106
.....................
Rear A/C Control .113
.......................
Air Pressure, Tires .258
......................................
Antif reeze .242
...............
Anti-lock Brakes (ABS) .209
...............................
Indicator . 63, 210
...................................
Operation .209
..............
Anti-thef t, Audio System .139
.
Anti-thef t Steering Column Lock .81
................................
Audio System .115
...
Automatic Seat Belt Tensioners .23
...
Automatic Lighting Off Feature .76
.............
Automatic Speed Control .175
..............
Automatic Transmission .200
..........................
Capacity, Fluid .288 ...............
Checking Fluid Level .244
.......................................
Shif ting .200
.
Shif t Lever Position Indicator .200
................
Shif t Lever Positions .201
....................
Shif t Lock Release .203
Battery Charging System ...........................
Indicator . 62, 276
............................
Jump Starting .272
..............................
Maintenance .262
............................
Specif ications .289
..............................
Bef ore Driving .185
..................................
Belts, Seat . 10, 21
...........................
Beverage Holders .99
..................................
Booster Seats .54
Brakes
...........
Anti-lock System (ABS) .209
.............
Break-in, New Linings .186
....................
Bulb Replacement .252
...........................................
Fluid .246
.........................................
Parking .97
.................
System Indicator . 63, 278
........................
Wear Indicators .209 .............................
Braking System .208
.................
Break-in, New Vehicle .186
..
Brightness Control, Instruments .76
........................
Brights, Headlights .75
Bulb Replacement
..........................
Back-up Lights .252
.....................
Brake Lights . 252, 253
................
Front Parking Lights .249
........
Front Side Marker Lights .249
.................................
Headlights .248
........
High-mount Brake Lights . 253
.................................
Rear Bulbs .252
............................
Specif ications .289
.............
Turn Signal Light . 249, 252
..............................
Bulbs, Halogen .248
............................
Capacities Chart .288
.............
Carbon Monoxide Hazard . 57
.............................
Carrying Cargo .193
.............
CAUTION, Explanation of . iii
..........................
CD Changer . 131, 134
.......................................
CD Player .130
Index
A
B
C
INDEX
I