2007 FORD FIESTA Electrical

303-00-30 Engine System - General Information 303-00-30
DIAGNOSIS AND TESTING
Measure the oil ressure (Engine
- 2.OL
Duratec-HE (MI 1 ))
I. Raise and support the vehicle. REFER to:
(I 00-02 Jacking and Lifting)
Jacking (Description and Operation),
Lifting (Description and Operation).
2. Disconnect the oil pressure switch electrical
connector from the oil pressure switch.
3. Remove the oil pressure switch.
6. N0TE:OiI pressure at 2000 rpm: 3.5 bar.
Measure the oil pressure.
7. Raise and support the vehicle. REFER to:
(1 00-02 Jacking and Lifting)
Jacking (Description and Operation), Lifting (Description and Operation).
8. Detach the oil pressure gauge and connector
from the oil pressure switch bore.
9. Coat the oil pressure switch with adhesive.
4. Attach the oil pressure gauge
(GV 2134) with ICL Install the pressure switch=
the oil pressure gauge connector to the oil
pressure switch bore, and position it to allow
reading from above.
5. Lower the vehicle.
2006.0 Fiesta 1212006 GI 52554en
procarmanuals.com

303-00-31 Engine System - General Information 303-00-31
DIAGNOSIS AND TESTING
11. Connect the oil pressure switch electrical
connector to the oil pressure switch.
12 Lower the vehicle.
Valve train analysis - static (engine off)
Remove the valve cover.
Check all components of the valve train for damage
and wear. Make sure that only original components
are installed and that all nuts and bolts are
tightened to the specified torque.
2006.0 Fiesta 1212006 GI 52554en
procarmanuals.com

Engine - 1.25L Duratec-I 6V (Sigma)ll.4L
303-01A-I 9 Duratec-1 6V (Sigma)/l .6L Duratec-1 6V (Sigma) 303-OIA-I 9
IN-VEHICLE REPAIR
Intake Manifold(21 183 0)
Removal 6. Remove the intake manifold lower retaining
bolt.
A WARNING:Do not smoke or carry lighted
tobacco or open flame of any type when
working on or near any fuel related
components. Highly flammable mixtures
are always present and may ignite. Failure
to follow these instructions may result in
personal injury.
1. Release the fuel system pressure. For
additional information, refer to
Section
31 0-00 [Fuel System - General
Information].
2. Disconnect the battery ground cable. For
additional information, refer to
Section
414-01 [Battery, Mounting and 7. Disconnect the engine wiring harness
Cables]. electrical connector.
3. Remove the air cleaner. For additional
information, refer to Section
303-1 2 [Intake
Air Distribution and Filtering].
4. Detach the power steering fluid reservoir
from the bracket and position
it to one side.
5. Remove the accessory drive belt. For
additional information, refer to
Section
303-05 [Accessory Drive].
8. Disconnect the positive crankcase ventilation
(PCV) hose from the PCV.
2006.0 Fiesta 1212006 GI 83728en
procarmanuals.com

Engine - 1.25L Duratec-1 6V (Sigma)llm4L
303-01 A120 Duratec-1 6V (Sigma)ll .6L Duratec-1 6V (Sigma)
303-01 Am20
IN-VEHICLE REPAIR
9. Disconnect the brake booster vacuum line
from the intake manifold. 12. Detach the oil level indicator tube from the
intake manifold.
/'-
10. Disconnect the evaporate emission (EVAP) 13. Disconnect the temperature and manifold
hose from the EVAP valve. absolute pressure (T-MAP) sensor electrical
connector.
11. Disconnect the knock sensor (KS) electrical
connector.
14. Disconnect the throttle plate control motor
(DC-ISC) electrical connector.
2006.0 Fiesta 1212006 GI 83728en
procarmanuals.com

Engine - 1.25L Duratec-I 6V (Sigma)ll14L
Duratec-1 6V (Sigma)ll16L Duratec-1 6V (Sigma)
IN-VEHICLE REPAIR
15. Disconnect the generator electrical 17. Disconnect the fuel injector electrical
connector. connectors and
position it with the engine
i wiring harness to one side.
16. Detach the generator from the engine.
1. Remove the bolts.
2. Remove the nut and the stud.
18. Disconnect the engine coolant temperature
(ECT) sensor electrical connector.
2006.0 Fiesta 1~12006 GI 83728en
procarmanuals.com

Engine - 1.25L Duratec-1 6V (Sigma)llI4L
Duratec-1 6V (Sigma)/l .6L Duratec-1 6V (Sigma)
IN-VEHICLE REPAIR
6. Connect the fuel supply line quick release
coupling. For additional information, refer to
Section 310-00 [Fuel System
- General
Information].
7. Attach the fuel line to the intake manifold.
Install the cable tie. 8.
Connect the fuel injector electrical
connectors.
9. Connect the engine coolant temperature
(ECT) sensor electrical connector.
10. Attach the generator to the engine.
1. Install the stud and nut.
2006.0 Fiesta 1212006 GI 83728en
procarmanuals.com

Engine - 1.25L Duratec-1 6V (Sigma)ll.4L
Duratec-1 6V (Sigma)ll .6L Duratec-1 6V (Sigma)
IN-VEHICLE REPAIR
2. Install the bolts.
I I. Connect the generator electrical connector.
12. Connect the throttle plate control motor
(DC-ISC) electrical connector.
13. Connect the temperature and manifold
absolute pressure (T-MAP) sensor electrical
connector.
14. Attach the oil level indicator tube to the
intake manifold.
15. Connect the knock sensor (KS) electrical
connector.
2006.0 Fiesta 1212006 GI 83728en
procarmanuals.com

Engine - 1.25L Duratec-1 6V (Sigma)ll.4L
303-01 A-26 Duratec-1 6V (Sigma)Il.GL Duratec-1 6V (Sigma) 303-01 A-26
IN-VEHICLE REPAIR
16. Connect the evaporate emission (EVAP)
hose to the EVAP valve.
17. Connect the brake booster vacuum line to
the intake manifold.
19. Connect the engine wiring harness
electrical connector.

20. Install the intake manifold lower retaining
bolt and the generator bracket retaining
bolts.
18. Connect the positive crankcase ventilation
(PCV) hose to the PCV.
21. Install the accessory drive belt. For
additional information, refer to
Section
303-05 [Accessory Drive].
22. Attach the power steering fluid reservoir to
the bracket.
23. Install the air cleaner. For additional
information, refer to Section
3031 2 [Intake
Air Distribution and Filtering].
2006.0 Fiesta 1212006 GI 83728en
procarmanuals.com