2007 FORD FIESTA Timing

303-01 B-44 Engine - 2.OL Duratec-HE (M14) 303-01 B-44
IN-VEHICLE REPAIR
6. Install the special tool. Tighten
the camshaft sprocket retaining
bolts.
,
7. Coat the engine front cover upper blanking
plug with sealant.
11. Remove the special tool.
8. Tension the timing chain.
Remove the timing chain guide securing bolt
and install the engine front cover upper
blanking plug.
12. Raise and support the vehicle. For
additional information, refer to: (1
00-02
Jacking and Lifting) I I Jacking (Description and Operation),
9. N0TE:Only rotate the crankshaft in the Lifting
(Description and Operation).
normal direction of rotation.
13. Remove the special tool.
Rotate the crankshaft until piston No.
I is at
TDC.
10.
N0TE:Hold the camshafts by the hexagon
with an open-ended wrench to stop them
from rotating.
14.
N0TE:Only rotate the crankshaft in the <
normal direction of rotation.
2006.0 Fiesta 1212006 G451293en
procarmanuals.com

303-01 B-45 Engine - 2.OL Duratec-HE (M14) 303-01 B-45
IN-VEHICLE REPAIR
Rotate the crankshaft approximately one and
Using a M6 x 18 mm bolt, check the position
three quarter revolutions until piston No.
I of the crankshaft pulley. 1 is 45 degrees before TDC.
18. Lower the vehicle.
15. Install the special tool. 19. N0TE:lf it is not possible to install the
special tool, correct the valve timing.
Using the special tool, check the position of
the camshafts.
16. N0TE:Only rotate the crankshaft in the
normal direction of rotation.
Rotate the crankshaft until piston No.
1 is at
TDC.
20. Remove the special tool.
17' ACAUTION:O~I~ tighten the crankshaft
pulley securing bolt finger tight.
N0TE:lf it is not possible to install the crankshaft
pulley securing bolt, correct the valve timing.
2006.0 Fiesta 1212006 G451293en
procarmanuals.com

303-01 B-54 Engine - 2.OL Duratec-HE (M14) 303-01 B-54
IN-VEHICLE REPAIR
Oil Pump(21 714 0)
Special Tool(s)
15030A
Removal
Universal Flange Holding
Wrench 205-072 (1 5-03OA)
20507202
1. Remove the timing chain.
Adapter for 205-072
205-072-02 (1 5-030
A0 1 )
For additional information, refer to: Timing
Chain (303-01 Engine
- 2.OL Duratec-HE
(M14), Invehicle Repair).
2. Remove the oil pan.
For additional information, refer to: Oil Pan
(303-01 Engine
- 2.OL Duratec-HE (M14),
Invehicle Repair).
3. Remove the oil pump chain guide. 4.
Remove the oil pump chain tensioner.
(.
5. Using the special tools, loosen the oil pump
sprocket retaining bolt.
6. Remove the oil pump chain.
1. Remove the oil pump sprocket retaining bolt.
2. Remove the oil pump chain and the oil pump
sprocket.
2006.0 Fiesta 1212006 G37459en
procarmanuals.com

303-01 B-55 Engine - 2.OL Duratec-HE (M14) 303-01 B-55
IN-VEHICLE REPAIR
7. Remove the oil pump. 3.
Using the special tools, tighten the oil pump
sprocket retaining bolt.
Installation 4. Install the oil pump chain tensioner.
I. lnstall the oil pump.
Tighten the bolts in the sequence shown in
two stages.
Stage
I : 10 Nm
Stage
2: 23 Nm
2. N0TE:Do not tighten the oil pump sprocket
retaining bolt at this stage.
lnstall the oil pump chain.
1. lnstall the oil pump chain and the oil pump
sprocket.
2. lnstall the oil pump sprocket retaining bolt.
5. Install the oil pump chain guide.
6. lnstall the oil pan.
For additional information, refer to: Oil Pan
(303-01 Engine
- 2.OL Duratec-HE (M14),
In-vehicle Repair).
7. lnstall the timing chain.
For additional information, refer to: Timing
Chain (303-01 Engine
- 2.OL Duratec-HE
(M14), Invehicle Repair).
2006.0 Fiesta i212006 G37459en
procarmanuals.com

303-01 B-60 Engine - 2.OL Duratec-HE (M14) 303-01 B-60
IN-VEHICLE REPAIR
Engine Front Cover(21 148 0)
f'
General Equipment 6. Detach the coolant expansion tank and lay
I Vehicle jack it to one side.
Materials Name Specification
I Silicone Sealant I WSE-M4G323-A4 I
Removal
1. Remove the crankshaft belt pulley.
For additional information, refer to:
Crankshaft Pulley (303-01 Engine
- 2.OL
Duratec-HE (M14), Invehicle Repair).
2. Remove the timing cover lower bolts.
7. Support the engine with
a vehicle jack.
8. Remove the front engine mount.
Discard the front engine mount nuts.
3. Disconnect the crankshaft position (CKP)
sensor electrical connector.
4. Lower the vehicle.
5. Remove the power steering pump.
For additional information, refer to: Power
Steering Pump
- 2.OL Duratec-HE (M14)
(211 -02 Power Steering, Removal and
Installation).
9. Remove the coolant pump pulley.
2006.0 Fiesta 121~0o6 G451289en
procarmanuals.com

303-01 B-61 Engine - 2.OL Duratec-HE (M14) 303-01 B-61
IN-VEHICLE REPAIR
10. Remove the drive belt idler pulley.
11. Remove the timing cover upper bolts.
Remove the timing cover.
Apply sealer to the timing cover (bead
diameter:
3 mm).
3. Install the timing cover (engine shown
installation removed for clarity).
Tighten the bolts in the sequence shown.
1. Clean the sealing surfaces of the timing Tighten bolts I to 8 to a torque of 10 Nm.
cover and the cylinder block. Tighten bolt 9 to 48 Nm.
2. N0TE:lnstall the timing cover within 10 Tighten bolts 10 to 19 to a torque of 10 Nm.
minutes of applying the silicon sealer.
2006.0 Fiesta 12/2006 G451289en
procarmanuals.com

303-01 B-67 Engine - 2.OL Duratec-HE (M14) 303-01 B-67
IN-VEHICLE REPAIR
Timing Chain(21 314 0) ,
Removal 4. Remove the timing chain guides.
1. Remove the engine front cover.
For additional information, refer to Engine
Front Cover
- in this section.
2. Detension the timing chain.
1. Unlock the timing chain tensioner ratchet.
2. Apply pressure to the timing chain guide.
3. Fix the timing chain tensioner with a suitable
pin punch.
3. N0TE:Hold the camshafts by the hexagon
with an open-ended wrench to stop them
from rotating.
Loosen the camshaft sprocket retaining
5. Remove the timing chain tensioner.
bolts.
Installation
1. Install the timing chain tensioner.
--
2006.0 Fiesta 1212006 G323910en
procarmanuals.com

303-01 B-68 Engine - 2.OL Duratec-HE (M14) 303-01 B-68
IN-VEHICLE REPAIR
2. Install the timing chain guides.
3m ACAUTION:D~ not tighten the camshaft
sprocket retaining bolts at this stage. Make
sure the camshaft sprockets rotate on the
camshafts.
Install the camshaft sprockets.
Install the timing chain.
4. Tension the timing chain.
Apply pressure to the timing chain and
remove the securing pin.
5. N0TE:Hold the camshafts by the hexagon
with an open ended wrench to stop them
from rotating.
Tighten the camshaft sprocket retaining
bolts.
6. Install the engine front cover.
For additional information, refer to Engine
Front Cover
- in this section.
2006.0 Fiesta 1212006 G323910en
procarmanuals.com