2007 FORD FIESTA wheel

204-00-1 5 Suspension System - General Information 204-00-1 5 1
DIAGNOSIS AND TESTING
2. If there is any free movement install a new lower 4. Compress and pull the piston rod in the vertical
arm. position. Feel if the resistance force at the point
REFER to: Lower Arm (204-01 Front
Suspension, Removal and Installation).
3. If a new lower arm is installed it will be
necessary to check and adjust the front wheel
alignment.
REFER to: Specifications (204-00 Suspension
System
- General Information, Specifications). of direction change-over
is perceptible without
a lag. If a lag is perceptible it is an indication of
damper valve damage and new struts or shock
absorbers must be installed. REFER to:
Front Strut and Spring Assembly (204-01 Front
Suspension, Disassembly and Assembly),
Front Strut and Spring Assembly (204-01 Front
Suspension, Removal and Installation),
Rear Shock Absorber (204-02 Rear Suspension,
Removal and Installation).
Strut or Shock Absorber Inspection
N0TE:lnspect the struts or shock absorber for
signs of oil
weepage or leaks. Make sure that the
oil is not from another source.
Weepage:
deposits a thin film of oil on the strut and spring
assembly or shock absorber.
is normally noticed due to a collection of dust
on the strut and spring assembly or shock
absorber.
occurs during the normal running-in period of
4800
- 8050 km. After this period no new signs
of oil should be visible.
does not require new struts or shock absorbers
to be installed.
Leakage:
covers the entire strut and spring assembly or
shock absorber with oil.
will drip oil onto the surrounding suspension
components.
requires new struts or shock absorbers to be
installed.
Strut or Shock Absorber Testing
N0TE:Struts or shock absorbers must be tested
in the vertical position.
I. Remove both strut and spring assemblies or
shock absorbers. The piston rods should extend.
Disassemble the strut and spring assemblies.
REFER to: Front Strut and Spring Assembly
(204-01 Front Suspension, Disassembly
and Assembly).
2. Compress the piston rods. Both piston rods
should offer the same resistance when
compressing.
3. Compress and release the piston rods. The
piston rods should extent equally.
2006.0 Fiesta 1212006 Gl49885en
procarmanuals.com

204-00-1 6 Suspension System - General Information 204-00-1 6
GENERAL PROCEDURES
Wheel Bearing Inspection
Special Tool(s)
General Equipment
I Dial indicator gauge I
bearing assembly. There should be no end (
play. If end play exists, install new wheel
bearings.
Check
1. N0TE:Do not to confuse lower arm ball joint
looseness with bearing looseness.
Raise and support the front of the vehicle. 6.
Install the front brake caliper anchor plate.
For additional information, refer to: (I 00-02)
For additional information, refer to: Brake
Jacking (Description and Operation),
Lifting (Description and Operation).
2. Check for loose front wheel bearings by
rocking the wheels at the top and bottom.
3. Spin the wheel quickly by hand and make
sure the wheel turns smoothly without noise
from the wheel bearings.
4. Remove the front brake caliper anchor plate.
For additional information, refer to: Brake
Caliper Anchor Plate (206-03, Removal and
Installation).
5. Position a suitable Dial indicator gauge
fixture or equivalent, against the wheel hub,
then push and pull the wheel hub. Measure
the end play of the wheel hub and front wheel Caliper
Anchor Plate (206-03, Removal and
Installation).
2006.0 Fiesta 1212006 ~25341 en
procarmanuals.com

204-01 -1 Front Suspension 204-01 -1
SECTION 204-01 Front Suspension
VEHICLE APPLICATION:2006.0 Fiesta
CONTENTS
SPECIFICATIONS
Specifications.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
.DESCRIPTION AND OPERATION
Front Suspension ........................................................................\
........................................
DIAGNOSIS AND TESTING
Front Suspension ........................................................................\
........................................
PAGE
REMOVAL AND INSTALLATION
Front Stabilizer Bar Bushing ...... .... . . . . . . .. . . .. . . .. .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (14 754 0)
204-01 -6
Lower Arm ........................................................................\
.............................. (14 706 0) 204-0 1 -7
Front Stabilizer Bar ........................................................................\
................. (14 752 0) 204-0 1 -9
Wheel Knuckle.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (1 4 343 0)
204-01 -1 3
i Front Strut and Spring Assembly ................................................................... (14 781 0) 204-01-19
Front Wheel Bearing ........................................................................\
........... (14 411 0) 204-01 -21
DISASSEMBLY AND ASSEMBLY
Front Strut and Spring Assembly ............................................................... (14 783 4)
204-01 -23
procarmanuals.com

204-01 -2 Front Suspension 204-01 -2
SPECIFICATIONS
I Top mount retaining nuts I 25 I 18 I - I
Torque Specifications
I Thrust bearing retaining nut I 48 I 35 I - I
Stabilizer bar connecting link to strut and spring
retaining nut Ib-in
I Wheel
knuckle to suspension strut pinch bolt I 85 I 63 I - I
Ib-ft Item Nm
Brake caliper anchor plate retaining bolts
Lower arm ball joint to wheel knuckle retaining nut
I Steering gear retaining bolts I 48 I 35 I - I
Tie-rod end retaining nut
Stabilizer bar clamp retaining bolts
Stabilizer bar to connecting link retaining nut
Fb.wer arm front retaining bolt I
70
48
I Lower arm rear clamp retaining bolts I 55 I 41 I - I
48
55
55
I Crossmember front retaining bolts I 70 I 52 I - I
52
35
I Crossmember rear retaining bolts 1 Iq5 1 85 I - I
-
-
35
41
41
I Crossmember inner and outer retaining bolts 1 175 1 129 1 - I
-
-
-
I Wheel hub retaining nut 1290 1214 1 - I
I Engine support insulator center bolt I 48 I 35 I - I
2006.0 Fiesta 1212006 GI 52539en
Wheel speed sensor retaining nut
a) Refer to the procedure in this section.
9 - 80
procarmanuals.com

204-01 -3 Front Suspension 204-01 -3
DESCRIPTION AND OPERATION
Front Suspension
Overview
N0TE:During installation of the front wheel bearing
it is important to adhere to the specified installation
position, as the anti-lock brake system
( ABS )
sensor ring is located in the wheel bearing. A
coloured rubber ring is provided to indicate the
correct installation position. If the wheel bearing
were to be installed incorrectly then this would
cause failure of the ABS
.
A newly developed Mc-Pherson front suspension
with L-shaped lower arms is used. These lower
suspension arms are linked via large rubber
mountings to a reinforced and extremely rigid front
axle crossmember.
The ball head between the lower suspension arm
and the suspension strut is secured with three
rivets. Toe-in is adjusted via adjustable track rods.
The lower suspension arms can only be replaced as a complete unit.
2006.0 Fiesta IZIZOO~ GI 67080en
procarmanuals.com

204-0 I -7 Front Suspension 204-0 1 -7
REMOVAL AND INSTALLATION
Lower Arm(l4 706 0)
Removal
1. Remove the wheel and tire. For additional
information, refer to Section
204-04 [Wheels
and Tires].
2m ncAu~10N:~rotect the ball joint seal using
a soft cloth to prevent damage.
Detach the lower arm ball joint from the
wheel knuckle.
Remove the heat shield.
3. Remove the crossmember outer retaining
bolt.
4. Remove the lower arm.
Installation
1. N0TE:Do not fully tighten the lower arm to
crossmember retaining bolts at this stage.
Install the lower arm.
2. Install the crossmember outer retaining bolt.
3m ~CAUTION:M~~~ sure the heat shield is
installed to prevent damage to the ball joint.
2006.0 Fiesta 1212006 GI 83757en
procarmanuals.com

204-0 I -8 Front Suspension 204-01 -8
REMOVAL AND INSTALLATION
Install the heat shield. 2. Tighten the bolts.
7. Check the toe setting and adjust as
4m ACAUTION:T~~ lower arm pinch bolt must necessary. For additional information, refer
be installed from the rear of the wheel
to Section 204-00 [Suspension System -
knuckle. General Information].
Attach the lower arm ball joint to the wheel
knuckle.
5, Install the wheel and tire. For additional
information, refer to Section
204-04 wheels
and Tires].
6. N0TE:The lower arm to crossmember
retaining bolts must be tightened with the
vehicle weight on the road wheels.
Tighten the lower arm to crossmember
retaining bolts.
1. Tighten the bolt in two stages.
Stage I: 80 Nm.
Stage 2: 55 degrees.
2006.0 Fiesta 1212006 GI 83757en
procarmanuals.com

204-01 -9 Front Suspension 204-0 I -9
REMOVAL AND INSTALLATION
Front Stabilizer Bar(l4 752 0)
i , Special Tool(s1
General Equipment
205524
I Transmission jack 1
Alignment Pins, Subframe
205-524 (1 5-1 22)
I Wooden block I
Removal
1. N0TE:Make sure the road wheels are in the
straight ahead position.
Centralize the steering and lock
it in position.
2. Detach the steering column shaft from the
steering gear pinion.
Discard the retaining bolt.
3. Raise and support the vehicle.
For additional information, refer to: Jacking
(100-02 Jacking and Lifting, Description
and Operation)
I Lifting (1 00-02 Jacking and Lifting,
Description and Operation).
4. N0TE:Use a 5 mm Allen key to prevent the
ball joint from rotating.
Detach the stabilizer bar connecting link from
the stabilizer bar on both sides.
5. Remove the engine support insulator.
2006.0 Fiesta 1212006 GI 83758en
procarmanuals.com