2007 FORD FIESTA cam

303-00-32 Engine System - General Information 303-00-32
GENERAL PROCEDURES
Camshaft Bearing Journal Diameter
1. Determine the diameter of the camshaft
journals.
Using a micrometer measure the diameter
at
90 degrees intervals to determine if the
journals are out-of-round.
Measure at two different points on the journal
to determine if there is any tapering.
If the measurements are out of the specified
range, install a new camshaft.
2006.0 Fiesta 1212006 GI 7620en
procarmanuals.com

303-00-33 Engine System - General Information 303-00-33
GENERAL PROCEDURES
Camshaft Bearing Journal Clearance
1. N0TE:Make sure that the following stages The value that is read off is the bearing
are followed exactly. The tappets or followers clearance.
must be removed to carry out this
measurement.
N0TE:Make sure that the camshaft is to
specification.
N0TE:The bearing caps and journals should be
free from engine oil and dirt.
Position on a width of plastigage on the
bearing cap.
Insert the camshaft, without lubrication, into
the cylinder head.
Position
a plastigage strip, which should be
equal to the width of the bearing cap, on the
bearing journal.
2. Following the tightening specification, install
the camshaft bearing caps. Refer to the
corresponding Section 303-01.
3.
N0TE:Do not strike the bearing caps.
Remove the camshaft bearing caps, refer to
the corresponding Section 303-01.
'4. Using the Plastigage, read off the
measurement.
Compare the width of plastigage with the
plastigage scale.
2006.0 Fiesta 1212006
procarmanuals.com

303-00-34 Engine System - General Information 303-00-34
GENERAL
PROCEDURES
Camshaft End Play
1. N0TE:Make sure that the camshaft is to
specification.
Using a Dial Indicator Gauge, measure the
end play.
Slide the camshaft in both directions. Read
and note the maximum and minimum values
on the Dial lndicator Gauge.
End play = maximum value minus minimum
value
If the measurement is out of specification,
install new components.
2006.0 Fiesta 1212006 GI 7622en
procarmanuals.com

303-00-35 Engine System - General Information 303-00135
GENERAL PROCEDURES
Camshaft Surface l nspection
I
I. Inspect the camshaft lobes for pitting or
damage in the active area. Minor pitting is
acceptable outside the active area.
2006.0 Fiesta 1212006 GI 7623en
procarmanuals.com

303-00-36 Engine System - General Information 303-00-36
GENERAL PROCEDURES
Camshaft Lobe Lift
1. Determine the cam lift.
Using a micrometer measure the cam in two
directions.
The difference between the two
measurements is the cam
lift.
2006.0 Fiesta 1212006 GI 7624en
procarmanuals.com

303-01 A-I Engine
. 1.25L Duratec-1 6V (Sigma)ll.4L
Duratec-I
6V (Sigma)ll . 6L Duratec-1 6V (Sigma)
303-01 A-I
SECTION 303-01A Engine . 1.25L Duratec-1 6V
(Sigma)/l.4L Duratec-I 6V (Sigma)/l . 6L Duratec-1 6V
(Sigma)
VEHICLE APPLICATION:2006.0 Fiesta
CONTENTS
SPECIFICATIONS
........................................................................\
.............................................. Specifications
Engine Data
. 1.25L ........................................................................\
................................
Engine Data . I . 4L ........................................................................\
..................................
Engine Data . 1.6L ........................................................................\
..................................
Oil pressure ........................................................................\
.............................................
Engine Oil Capacity . - 1.25Ll1.4L ........................................................................\
............
Engine Oil Capacity - 1.6L ........................................................................\
......................
Valve Clearance - 1.25LlI . 4L ........................................................................\
..................
Valve Clearance - 1.6L ........................................................................\
............................
Cylinder block - 1.25L ........................................................................\
.............................
Cylinder block - 1.4L ........................................................................\
...............................
........................................................................\
............................... Cylinder block - 1.6L
........................................................................\
.......................................... Cylinder head
Piston
-1.25L ........................................................................\
...........................................
Piston -1.4L ........................................................................\
.............................................
Piston - l.6L ........................................................................\
............................................
PAGE
DESCRIPTION AND OPERATION
........................................................................\
......................................................... Engine 303-01A-9
........................................................................\
.................... 1.4Ll1.6L Duratec 16V engine 303-01A-9
DIAGNOSIS AND TESTING
........................................................................\
......................................................... Engine 303-01A-12
GENERAL PROCEDURES
........................................................................\
....................... Valve Clearance Adjustment 303-01 A-I 3
IN-VEHICLE REPAIR
Crankshaft Front Seal ........................................................................\
......... (21 467 0)
Valves ........................................................................\
..................................... (21 21 5 4)
Intake Manifold ........................................................................\
....................... (21 183 0)
Valve Cover ........................................................................\
............................ (21 141 0)
Valve Seals ........................................................................\
............................. (21 238 0)
Camshafts ........................................................................\
........................ (21 284 0)
Camshaft Seal ........................................................................\
................... (21 288 0)
Timing Belt ........................................................................\
.......................... (21 304 0)
Exhaust Manifold ........................................................................\
.................... (21 187 0)
Cylinder Head ........................................................................\
...................... (21 163 0)
Oil Pan ........................................................................\
............................. (21 154 0)
procarmanuals.com

Engine - 1.25L Duratec-1 6V (Sigma)ll.4L
Duratec-1 6V (Sigma)Il.GL Duratec-1 6V (Sigma)
SPECIFICATIONS
2006.0 Fiesta 1212006 GI 54208en
Ib-in
-
-
-
-
-
-
-
-
-
80
-
80
-
35
-
80
-
-
-
-
-
-
80
80
-
-
-
53
-
80
80
Ib-ft
41
35
66
35 35 18
30
18
35
-
20
-
15
-
21
-
11
-
-
13
-
35
-
-
11
15
15
-
-
-
-
Description
Engine front mount bracket to cylinder block
retaining bolts
Engine front mount retaining nuts and bolts
Engine rear mount center retaining nut
Engine rear mount outer retaining nuts
Engine support insulator retaining bolts Power steering line support bracket retaining bolts
Power steering line to power steering pump
Air conditioning
(AIC) compressor to cylinder block
retaining bolts
Generator to cylinder block top rear and lower
retaining bolts
Water pump retaining bolts
Water pump pulley retaining bolts
Oil pump to cylinder block retaining bolts
Oil pan to cylinder block retaining bolts
Oil level indicator tube bracket retaining bolt
Engine oil drain plug
Oil pump pickup pipe to cylinder block retaining
bolts
Oil pressure switch
Cylinder head bolts
Valve cover retaining bolts
Intake manifold to cylinder head retaining bolts
Exhaust manifold to cylinder head
Exhaust manifold to cylinder block
Camshaft position (CMP) sensor
Timing belt rear cover retaining bolts
Spark plugs Engine rear lifting eye retaining bolts
Coolant distribution housing retaining bolts
Ignition coil to coolant distribution housing
Camshaft bearing cap retaining bolts
Timing belt upper cover to cylinder block retaining
bolts
Timing belt lower cover to cylinder block retaining
bolts
Nm
55
48 90
48
48 25
40 25
47
9
27 9
20 4
28 9
15
a)
a)
18
a)
47 9
9
15
20
20
6
a)
9
9
procarmanuals.com

Engine - I .25L Duratec-1 6V (Sigma)llI4L
Duratec-1 6V (Sigma)ll .6L Duratec-I 6V (Sigma)
SPECIFICATIONS
1 Description I Nm I Ib-ft I Ib-in I
I Camshaft pulley retaining bolt I 60 I 44 I - I
Timing belt tensioner two bolts fixing
Timing belt tensioner central bolt fixing
Crankshaft position (CKP) sensor bracket to
cylinder block retaining bolts
I Crankshaft rear oil seal carrier retaining bolts I 9 1 - I 80 I
20
25
I Cylinder block blanking plug I 20 I 15 1 - I
I Crankshaft pulley retaining bolt I a) I - I - I
15
18
I Engine coolant temperature (ECT) sensor I 18 I 13 I - I
-
-
I Exhaust manifold studs I 10 I - I 89 I
Positive crankcase ventilation (PCV) cover retaining
1 bolts Fuel
rail to intake manifold
Knock sensor (KS) retaining bolt
I Thermostat housing retaining bolts I 9 I - 1 80 I
I Flywheel to crankshaft retaining bolts I a) I - I - I
15
20
I Selector lever cable bracket to transaxle I 20 I 15 I I
11
15
Transaxle retaining bolts
Torque converter retaining nuts
I Intermediate shaft center bearing cap retaining nuts 1 25 I 18 I - I
-
-
I Ground cable to cylinder head retaining bolt I 18 I 13 I - I
47
27
Suspension strut and spring assembly top mount
retaining nuts
I a) Refer to procedure in this section.
35
20
2006.0 Fiesta 1212006 GI 54208en
-
procarmanuals.com