2007 FORD FIESTA engine

Engine - 1.25L Duratec-1 6V (Sigma)lIa4L
Duratec-1 6V (Sigma)ll .6L Duratec-1 6V (Sigma)
ASSEMBLY
72. Tighten the exhaust manifold lower 75, Install the exhaust manifold lower heat
. retaining bolts. shield left-hand retaining bolts. I
73. Install the exhaust manifold upper heat
shield.
74. Install the exhaust manifold lower heat
shield right-hand retaining bolts.
2006.0 Fiesta 1212006 GI 54225en
procarmanuals.com

Engine - 1.25L Duratec-1 6V (Sigma)ll.4L
303-01 A-I 22 Duratec-1 6V (Sigma)/l .6L Duratec-1 6V (Sigma)
303-01 A-1 22
INSTALLATION
Engine
Special Tool(s) 2. Install the transaxle lower retaining bolts. \.,
622
I I Remover/lnstaller, Hose
Wrench,
Hydraulic Line Union
"-269 (I 3-027)
- --
21 068A
Clamp
303-397 (24-003)
ift tins racket, Engine
303-1 22 (2 1 -068A)
General Equipment
I Securing straps I
I Workshop table I
I Engine hoist I
Installation
All vehicles
A WARN1NG:Do not smoke or carry lighted
tobacco or open flame of any type when
working on or near any fuel related
components. Highly flammable mixtures
are always present and may ignite. Failure
to follow these instructions may result in
personal injury.
I' ACAUTION:M~~~ sure that the two locating
dowels are installed.
Install the transaxle to the engine.
3m AWARNING:S~~~~~~ the engine and
transaxle assembly on wooden blocks and
secure
it with suitable securing straps.
Using the special tool and the engine hoist
position the engine and transaxle assembly
on the workshop table.
4. lnstall the transaxle right-hand retaining bolt.
2006.0 Fiesta 1212006 GII 3164en
procarmanuals.com

Engine - 1.25L Duratec-1 6V (Sigma)ll.4L
303-01A-123 Duratec-1 6V (Sigma)/l .6L Duratec-1 6V (Sigma) 303-01 A-I 23
INSTALLATION
5. Install the starter motor and the transaxle Install the engine rear mount.
left-hand retaining bolt.
/'
10. lnstall the battery tray support bracket.
6. Raise and support the vehicle.
For additional information, refer to: Lifting
(1 00-02 Jacking and Lifting, Description
and Operation).
7. Position the engine and transaxle assembly
in the engine compartment.
Carefully lower the vehicle.
8.
N0TE:lnstall new engine front mount
, retaining nuts. ' I ' N0TE:Do not tighten the engine front mount
retaining bolts and nuts at this stage.
Install the engine front mount. 11. Install the engine rear support insulator.
9.
N0TE:lnstall new engine rear mount 12. CAUTIONS:
retaining nuts.
Asupport the halfshaft. The inner joint N0TE:Do not tighten the engine rear mount center must not be bent more than 18 degrees. retaining nut at this stage. The outer joint must not be bent more than
45 degrees.
ADO not damage the halfshaft oil seal.
N0TE:lnstall a new center bearing cap and
locknuts.
2006.0 Fiesta 1212006 GII 31 64en
procarmanuals.com

Engine - 1.25L Duratec-1 6V (Sigma)ll.4L
303-01 A-I 24 Duratec-1 6V (Sigma)/l .6L Duratec-1 6V (Sigma)
303-01 A-1 24
INSTALLATION
Attach the right-hand halfshaft and the Install the heat shield.
intermediate shaft to the transaxle.
13. CAUTIONS:
Asupport the halfshaft. The inner joint
must not be bent more than
18 degrees.
The outer joint must not be bent more than
45 degrees.
ADO not damage the halfshaft oil seal.
A~ake sure the snap ring is correctly
seated.
N0TE:lnstall a new snap ring.
Attach the left-hand halfshaft to the
transaxle.
14. Attach the lower arm to the wheel knuckle
on both sides (right-hand side shown).
15. Using the special tool, connect the coolant
hose to the distribution pipe
16. Using the special tool, connect the coolant
hose to the radiator.
2006.0 Fiesta 1212006 Gll3164en
procarmanuals.com

Engine - 1.25L Duratec-1 6V (Sigma)ll.4L
Duratec-1 6V (Sigma)/lI6L Duratec-1 6V (Sigma)
INSTALLATION
17. Connect the AIC high-pressure cut-off
. switch electrical connector.
20. Using the special tool, attach the power
steering line to the power steering pump.
18. Install the cooling fan motor and shroud. 21. Connect the power steering line to the
1. Push the cooling fan motor and shroud steering pump.
upwards and then downwards to install.
2. Install the cooling fan motor and shroud to
the retaining brackets.
19. Connect the cooling fan motor and cooling
fan resistor electrical connectors.
22. Attach the power steering line support
bracket to the engine block.
2006.0 Fiesta 1212006 GII 31 64en
procarmanuals.com

303-01 A-I 26 Engine
- 1.25L Duratec-I 6V (Sigma)ll.4L
Duratec-1 6V (Sigma)ll .6L
Duratec-1 6V (Sigma) 303-01A-I26
INSTALLATION
23. Attach the air conditioning (NC)
compressor to the
cylinder block.
27. Connect the reversing lamp switch
electrical connector.
I
24. Connect the NC compressor clutch
28. Connect the crankshaft position (CKP)
electrical connector. sensor electrical connector.
25. Install the accessory drive belt. 29. Connect the oil pressure switch electrical
For
additional information, refer to: connector.
Accessory Drive
Belt - I .4L Duratec-16V
(Sigma)ll .6L Duratec-1 6V (Sigma),
Vehicles With: Air Conditioning (303-05
Accessory Drive,
Removal and
Installation).
26. Connect the starter motor electrical
connectors.
30.
N0TE:lnstall new exhaust flange nuts and
a new exhaust
flange gasket.
2006.0 Fiesta 1212006 Gll3164en
procarmanuals.com

Engine - 1.25L Duratec-1 6V (Sigma)ll.4L
303-01 A-I 27 Duratec-1 6V (Sigma)ll .6L Duratec-1 6V (Sigma)
303-01 A-I 27
INSTALLATION
Attach the exhaust flexible pipe to the
33. Attach the gearshift cables to the bracket
catalytic converter.
and turn the abutment sleeves
counterclockwise.
31. Remove the exhaust flexible pipe support.
Vehicles without automated gearshift
32m ACAUTION:H brake fluid is spilt on the
paintwork, the affected area must be
immediately washed down with cold water.
N0TE:Make sure the spring clip is correctly seated.
Connect the clutch slave cylinder supply
line.
Install the spring clip.
34. N0TE:Do not install the air cleaner at this
stage.
Adjust the gearshift cable.
For additional information, refer to: Gearshift Cable Adjustment (308-00 Manual
Transmission/Transaxle and Clutch
General Information, General Procedures).
35.
N0TE:Do not install the air cleaner at this
stage.
Bleed the hydraulic clutch system.
For additional information, refer to: Clutch
System Bleeding (308-00 Manual
Transmission/Transaxle and Clutch -
General Information, General Procedures).
Vehicles with automated gearshift
36. Connect the gearshift actuator electrical
connector (colored grey).
2006.0 Fiesta 1212006
procarmanuals.com

Engine - 1.25L Dura
303-01 A-I 28 Duratec-16V
(Sigma)/l .r
:eel 6V (Sigma)ll.4L
L
Duratec-1 6V (Sigma) 303-01A-128
INSTALLATION
37. Connect the gearshift actuator electrical All vehicles
connector (colored black). 41. Lower the vehicle.
42. Tighten the engine front mount retaining
nuts and bolts.
38. Install the gearshift actuator cover.
39. Connect the clutch slave cylinder supply
line.
Install the spring clip.
40. Bleed the hydraulic clutch system.
For additional information, refer to: Clutch
System Bleeding
- Vehicles With:
Automated Gearshift
(308-00 Manual
~ransmission/Transaxle and Clutch -
General Information, General Procedures).
43. N0TE:lnstall a new engine rear mount
center retaining nut.
Tighten the engine rear mount center
retaining nut.
44. Attach the power steering line support
bracket to the cylinder head.
2006.0 Fiesta 1212006 GII 31 64en
procarmanuals.com