2007 FORD FIESTA 303-01

303-01 B-I 16 Engine - 2.OL Duratec-HE (M14) 303-01 B-I
16
INSTALLATION
31. Attach the power steering pump to steering 34. N0TE:lnstall a new power steering pump
gear pressure line to the intake manifold. pulley.
f
32m &AUTION:C~~~ must be taken to prevent
dirt ingress. Using
the special tool, install the power

steering pump pulley.
-
Using the special tool, install a new O-ring 35. Install new power steering fluid reservoir
seal onto the power steering pump to O-ring
seals.
steering gear pressure line union.
1. Push the O-ring seal onto the special tool.
2. Locate the special tool onto the power
steering pump to steering gear pressure line
union and install the O-ring seal.
33. Attach the power steering pump to steering
gear pressure line from the power steering
Pump.
36. Install the power steering fluid reservoir.
2006.0 Fiesta 12/2006 G451291 en
procarmanuals.com

303-01 B-I17 Engine - 2.OL Duratec-HE (M14) 303-01 B-117
INSTALLATION
37. Using the special tool, connect the steering
Connect the clutch slave cylinder supply
gear to power steering fluid reservoir return
line.
I I line to the power steering fluid reservoir. Install the spring clip.
38.
Attach the steering gear to power steering 41. Connect the reversing lamp switch
fluid reservoir return line support bracket
electrical connector.
to the generator.
42. Lower the vehicle.
39. Connect the A/C low pressure switch
connector. 43. Install the coolant expansion tank.
40a &AUTION:I~ brake fluid is spilt on the
paintwork, the affected area must be
immediately washed down with cold water.
N0TE:Make sure the spring clip is correctly seated.
2006.0 Fiesta 1212006 ~451291 en
procarmanuals.com

303-01 B-I 18 Engine - 2.OL Duratec-HE (M14) 303-01 B-118
INSTALLATION
44. Attach the power steering high-pressure 47.
Connect the catalyst monitor sensor
line retaining bracket to the transaxle. electrical
connector.
//
45. Install the engine wiring harness bracket. 48.
Connect the power steering pump switch
electrical connector.
46. Connect the engine wiring harness
electrical connector.
49. Install the battery tray support bracket.
2006.0 Fiesta 1212006 G451291 en
procarmanuals.com

303-01 B-1/19 Engine - 2.OL Duratec-HE (M14) 303-01 B-119
INSTALLATION
50. Connect the brake booster vacuum line to
53. Tighten the strut and spring assembly top
the intake manifold. mount nuts.
/
51. Attach the evaporative emission (EVAP)
valve from EVAP valve support bracket.
I. Connect the EVAP valve electrical connector.
2. Connect the low pressure line to the EVAP
valve.
3. Push the EVAP valve onto the support
bracket.
52. Using the special tool, connect the coolant
hose to the coolant outlet connector. 54.
Install the right-hand
headlamp assembly.
For additional information, refer to:
Headlamp Assembly (41 7-01 Exterior
Lighting, Removal and Installation).
55. Attach the exhaust flexible pipe to the
exhaust manifold.
For additional information, refer to: Exhaust
Flexible Pipe
- 2.OL Duratec-HE (M14)
(309-00 Exhaust System, Removal and
Installation).
56. Install the cooling fan motor and shroud.
2006.0 Fiesta 1212006 ~451291 en
procarmanuals.com

303-01 8-1 20 Engine - 2.OL Duratec-HE (M14) 303-01 B-I 20
INSTALLATION
57. Connect the cooling fan motor and cooling
fan resistor electrical connectors.
58. Install the accessory drive belt.
For additional information, refer to:
Accessory Drive Belt
- 2.OL Duratec-HE
(M14) (303-05 Accessory Drive, Removal
and Installation).
59. Adjust the gearshift cables.
For additional information, refer to:
Gearshift Cable Adjustment (308-00
Manual
Transmission/Transaxle and
Clutch
- General Information, General
Procedures).
60. Bleed the hydraulic clutch system.
For additional information, refer to: Clutch
System Bleeding (308-00 Manual
Transmission/Transaxle and Clutch -
General Information, General Procedures).
61. Install the battery tray.
For additional information, refer to: Battery
Tray
- 2.OL Duratec-HE (M14) (414-01
Battery, Mounting and Cables, Removal
and Installation).
62. Install the air cleaner.
For additional information, refer to: Air
Cleaner
- 2.OL Duratec-HE (M14) (3031 2
Intake Air Distribution and Filtering,
Removal and Installation).
63. Fill and bleed the cooling system.
For additional information, refer to: Cooling
System Draining, Filling and Bleeding
(303-03 Engine Cooling - 2.OL Duratec-HE
(M14), General Procedures).
2006.0 Fiesta 1212006 G451291 en
procarmanuals.com

Engine Cooling - 1.3L Duratec-8V
(Rocam)ll.25L Duratec-1 6V (Sigma)llI4L
303-03A-22 Duratec-1 6V (Sigma)lIl6L Duratec-1 6V (Sigma) 303-03A-22
REMOVAL AND INSTALLATION
9. Remove the generator.
For
additional information, refer to:
Generator
- 1.25L Duratec-1 6V (Sigma)/l.4L
Duratec-I 6V (Sigma)/l .6L Duratec-I 6V
(Sigma)
(414-02 Generator and Regulator,
Removal and Installation).
10. Remove the water pump pulley.
Discard the gasket.
Vehicles built 0412005 onwards
13. Remove the timing belt.
For additional information, refer to: Timing
Belt (303-01 Engine - 1.25L Duratec-1 6V
(Sigma)ll.4L Duratec-1 6V (Sigma)ll .6L
Duratec-1 6V (Sigma), ln-vehicle Repair).
11. Remove the timing belt cover (cover shown 14. Drain the cooling system,
removed for clarity). For additional information, refer to: Cooling
12' &AUTION:P~~~~~~ the timing belt and
lower cover from contamination by the
coolant.
Remove the water pump. System
Draining,
Filling and Bleeding -
1.3L Duratec-8V (Rocam)ll.25L
Duratec-1 6V (Sigma)ll.4L Duratec-1 6V (,
(Sigma)ll .6L Duratec-1 6V (Sigma) (303-03
Engine
Cooling - 1.3L Duratec-8V
(Rocam)ll.25L Duratec-I 6V (Sigma)/l.4L
Duratec-1 6V (Sigma)ll .6L Duratec-1 6V
(Sigma), General Procedures).
15. Remove the water pump and the timing
belt
tensioner.
Discard the gasket.
2006.0 Fiesta 1212006 GI 89080en
procarmanuals.com

Fuel Charging and Controls - 2.OL
303-04B-22 Duratec-HE (M14) 303-04B-22
DIAGNOSIS AND TESTING
Symptom
Engine knock during accelera-
tion Possible
Sources Action
CKP sensor. Carry out a full engine
diagnosis using the guided
diagnostic menu in WDS.
INSPECT the fuel injectors.
CLEAN the fuel injectors or
INSTALL a new set of injectors
as required only after the
checks have been carried out.
I . Incorrect valve timing. I CHECK the valve timing. I
Excessive carbon build up. REMOVE the cylinder head.
INSPECT the cylinder head
and pistons for signs carbon
build up.
REFER to: Cylinder Head (303-
01 C, In-vehicle Repair).
Worn or damaged oil pump.
Worn or damaged timing chain
or sprocket.
Major mechanical engine
failure. INSPECT
the engine compon- I
ents.
KS.
Fuel injectors. Carry out a full engine
diagnosis using the guided
diagnostic menu in WDS.
INSPECT the fuel injectors.
CLEAN the fuel injectors or
INSTALL a new set of injectors
as required only after the
checks have been carried out.
Major mechanical engine
failure. REFER
to: Engine (303-01
Engine
- 2.OL Duratec-HE
(M14), Diagnosis and
Testing).
N0TE:Before proceeding with any
of the actions in relation to the
possible sources for excessive
fuel consumption, a fuel consumption test located in the
toolbox menu of WDS must be
performed.
Excessive fuel consumption Brakes binding. CHECK
the braking system.
REFER to: Brake System (206-
00, Diagnosis and Testing).
Vehicle overloaded, or
excessive wind resistance (roof
racks, towing etc).
ADVISE the customer about
the effects of overloading the
vehicle and wind resistance on
the fuel consumption.
2006.0 Fiesta 1212006 GI 65371 en
Air cleaner element blocked. INSTALL a new air cleaner .-
element. I
procarmanuals.com

Engine Emission Control - 1.3L Duratec-8V
(Rocam)llI25L Duratec-1 6V (Sigma)llm4L
303-O8A-7 Duratec-1 6V (Sigma)ll .6L Duratec-1 6V (Sigma) 303-0844-7
REMOVAL AND INSTALLATION
Crankcase Vent Oil Separator
i
Removal
1. Remove the air cleaner. For additional
information, refer to Section
303-1 2 [Intake
Air Distribution and Filtering].
2. Remove the intake manifold. For additional
information, refer to Section 303-01A
[Engine
-- 1.25L Duratec-1 6V (Sigma)ll.4L
Duratec-1 6V (Sigma)llm6L Duratec-1 6V
(Sigma)] I 303-01 B [Engine -- 1.4L
Duratorq-TDCi (DV) Diesel] I 303-01 C [Engine
-- 1.3L Duratec-8V (Rocam)] I 303-01 D
[Engine
-- 2.OL Duratec-HE (M14)I 1 303-01 E
[Engine
-- 1.6L Duratorq-TDCi (DV) Diesel].
3. Remove the crankcase vent oil separater.
Discard the gasket.
Installation
I. N0TE:lnstall a new crankcase vent oil
separator gasket.
To install, reverse the removal procedure.
2006.0 Fiesta 1212006 G210048en
procarmanuals.com