2007 FORD FIESTA brake

206-09C-5 Anti-Lock Control - Stability Assist 206-096-5
REMOVAL AND INSTALLATION
6. Disconnect the stability assist module
electrical connector.
11. Detach the HCU and stability assist module
assembly from the support bracket.
5. Detach the brake tubes from the bulkhead. 10. Remove the HCU and stability assist
7. Raise and support the vehicle. For additional
information, refer to Section
100-02 [Jacking 12. Remove the HCU to stability assist module
and Lifting]. retaining bolts.
i
8. Remove the HCU and stability assist module
support bracket lower retaining bolt. module
assembly and the support bracket.
9. Lower the vehicle.
13. Remove the HCU.
Installation
I. To install, reverse the removal procedure.
--- -- - --
2006.0 Fiesta 1212006 ~327341 en
procarmanuals.com

206-09C-6 Anti-Lock Control - Stability Assist 206-09C-6
REMOVAL AND INSTALLATION
2. Bleed the brake system. For additional
information, refer to Section 206-00 [Brake
System
- General Information].
2006.0 Fiesta 1212006 ~327341 en
procarmanuals.com

206-09C-12 Anti-Lock Control - Stability Assist 206-096-1 2
REMOVAL AND INSTALLATION
Stability Assist Module ,/.. ,
Materials Remove
the brake master cylinder to
hydraulic control unit (HCU) brake tubes. C
Name Specification I I
I Super DOT 4 brake fluid I ESD-M6C57-A I
Removal
CAUTI0N:If brake fluid is spilt on the
paintwork, the affected area must be
immediately washed down with cold water.
I. Remove the brake master cylinder. For
additional information, refer to
Section
206-06 [Hydraulic Brake Actuation].
2. Detach the engine wiring harness electrical I
connector from the wheelhouse assembly. 4. CAUTIONS:
3. CAUTIONS:
hap the brake tubes to prevent fluid loss
or dirt ingress.
Dplug the hydraulic control unit (HCU)
ports to prevent fluid loss or dirt ingress.
N0TE:Make a note of the position of the brake
tubes, to aid installation.
hap the brake tubes to prevent fluid loss
or dirt ingress.
nplug the HCU ports to prevent fluid loss
or dirt ingress.
N0TE:Make a note of the position of the brake
tubes, to aid installation.
Disconnect the brake tubes from the HCU.
2006.0 Fiesta 1~12006 G327320en
procarmanuals.com

206-096-1 3 Anti-Lock Control - Stability Assist 206-09C-13
REMOVAL AND INSTALLATION
5. Detach the brake tubes from the bulkhead. 10. Remove the HCU and stability assist
module assembly and the support bracket.
6. Disconnect the stability assist module
electrical connector.
11. Detach the HCU and stability assist module
assembly from the support bracket.
7. Raise and support the vehicle. For additional
information, refer to Section
100-02 [Jacking 12. Remove the HCU to stability assist module
and Lifting]. retaining bolts.
8. Remove the HCU and stability assist module
support bracket lower retaining bolt.
9. Lower the vehicle.
13. Remove the stability assist module.
Installation
I. To install, reverse the removal procedure.
2006.0 Fiesta 1212006 G327320en
procarmanuals.com

206-09C-14 Anti-Lock Control - Stability Assist 206-096-1 4
REMOVAL AND INSTALLATION
2. Bleed the brake system. For additional
information, refer to Section 206-00 [Brake
System
- General Information].
2006.0 Fiesta 1212006 G327320en
procarmanuals.com

211 -00-6 Steering System = General Information 21 1 =OO-6
DIAGNOSIS AND TESTING
Symptom Possible Sources Action
lncorrect wheel alignment. CHECK the wheel alignment
and adjust if necessary.
REFER to: (204-00 Suspension
System
- General Information) r
Specifications (Specifications), Front Toe Adjustment (General
Procedures).
lncorrect front axle cross-
member alignment.
Using the special tool, CHECK
the front axle crossmember
alignment.
Damaged or worn front wheel
bearings. CHECK and INSTALL new
front wheel bearings as neces-
sary.
REFER to: Front Wheel
Bearing (204-01 Front
Suspension, Removal and
Installation).
I CHECK the brake system. I
REFER to: Brake System (206-
00 Brake System
- General
Information, Diagnosis and
Testing).
CARRY OUT the steering
linkage component test.
REFER to Steering Linkage
Component Test in this
procedure.
CARRY OUT the steering
linkage component test.
REFER to Steering Linkage
Component Test in this
procedure.
Wheels and tires. I CHECK the wheels and tires. I
REFER to: Wheels and Tires
(204-04 Wheels and Tires,
Diagnosis and Testing).
Steering wheel 'off center Vehicle attitude incorrect (front
or rear is high or low). CHECK
for abnormal loading,
coil spring sag or non-standard
springs.
lncorrect wheel alignment. CHECK
the wheel alignment
and adjust if necessary.
REFER to: (204-00 Suspension
System
- General Information)
Specifications (Specifications),
Front Toe Adjustment (General
Procedures).
2006.0 Fiesta 1212006 GI 49906en
procarmanuals.com

21 1-00-1 6 Steering System - General Information 21 I -00-1 6
DIAGNOSIS AND TESTING
8m ACAUTION:T~ prevent damage to the
steering linkage, turn the steering wheel to
move the steering linkage to the steering
lock stop.
Turn the steering wheel to position the steering
linkage against the left-hand steering lock stop.
9. N0TE:To isolate the steering gear design
'clearance, check the left-hand
tiemrod with
the steering held against the left-hand
steering lock stop.
With the aid of another technician holding the
steering against the left-hand steering lock stop,
firmly grasp the left-hand road wheel and apply
a rocking motion to check for any free play in
the tie-rod.
IQ Detach the steering gear boot from the steering
gear body and check for free play at the tie-rod
inner ball joint.
11. If there is free play at the tie-rod inner ball joint,
install a new tie-rod.
REFER to: Tie Rod (211-03 Steering Linkage,
Removal and lnstallation).
I2 If there is free play at the tie-rod end, install a
new tie-rod end.
REFER to: Tie Rod End (21 1-03 Steering
Linkage, Removal and lnstallation).
Turning Effort Test
N0TE:Before carrying out this test, make sure that
the suspension components are serviceable.
N0TE:Before carrying out this test, make sure that
the steering column is serviceable.
N0TE:Before carrying out this test, make sure that
the front toe adjustment and tire pressures are
correct. 1.
Park the vehicle on a dry, even surface and
apply the parking brake.
/- ,
2. Remove the driver air bag module.
REFER to: Driver Air Bag Module (501 -20
Supplemental Restraint System, Removal and
Installation).
3. Remove the driver air bag module wiring
harness from the driver air bag module.
REFER to: Driver Air Bag Module Wiring
Harness (501 -20 Supplemental Restraint
System, Removal and Installation).
4. Connect the driver air bag module wiring
harness to the clockspring.
5. Connect the air bag simulators to the driver air
bag module wiring harness in place of the driver
air bag module at the top of the steering column.
6. Start the engine and turn the steering wheel
from lock to lock several times until the power
steering fluid has reached normal operating
temperature.
7. Using a suitable torque wrench and socket,
check the steering wheel turning effort.
8. If the steering wheel turning effort is greater than
the specification, install a new power steering -
pump. REFER to: i
Specifications (21 1-00 Steering System -
General Information, Specifications),
Power Steering Pump
- I .3L Duratec-8V
(Rocam) (21 1-02 Power Steering, Removal
and lnstallation),
Power Steering Pump
- 1.25L Duratec-1 6V
(Sigma)/l.4L Duratec-1 6V (Sigma)/l .6L
Duratec-l6V (Sigma), Vehicles With: Air
Conditioning (21 1-02 Power Steering,
Removal and lnstallation),
Power Steering Pump
- I .25L Duratec-I 6V
(Sigma)/l.4L Duratec-1 6V (Sigma)/l .6L
Duratec-I 6V (Sigma), Vehicles Without: Air
Conditioning (21 1-02 Power Steering, Removal and lnstallation),
Power Steering Pump
- 1.4L Duratorq-TDCi
(DV) Diesel (21 1-02 Power Steering, Removal
and lnstallation),
Power Steering Pump
- 2.OL Duratec-HE (M14)
(21 1-02 Power Steering, Removal and
Installation).
Disconnect the air bag simulators from the driver
air bag module wiring harness.
//
IQ Disconnect the driver air bag module wiring i,,.
harness from the clockspring.
2006.0 Fiesta 1212006 GI 49906en
procarmanuals.com

Engine - 1.25L Duratec-1 6V (Sigma)llm4L
303-01 A120 Duratec-1 6V (Sigma)ll .6L Duratec-1 6V (Sigma)
303-01 Am20
IN-VEHICLE REPAIR
9. Disconnect the brake booster vacuum line
from the intake manifold. 12. Detach the oil level indicator tube from the
intake manifold.
/'-
10. Disconnect the evaporate emission (EVAP) 13. Disconnect the temperature and manifold
hose from the EVAP valve. absolute pressure (T-MAP) sensor electrical
connector.
11. Disconnect the knock sensor (KS) electrical
connector.
14. Disconnect the throttle plate control motor
(DC-ISC) electrical connector.
2006.0 Fiesta 1212006 GI 83728en
procarmanuals.com