2007 FORD FIESTA drain bolt

21 1-02-48 Power Steering 21 1-02-48
REMOVAL AND INSTALLATION
Power Steering Fluid Cooler(l3 444 0)
Removal 2. Lower the power steering fluid cooler. '-..
I. Raise and support the vehicle. For additional
information, refer to:
(100-02 Jacking and
Lifting)
Jacking (Description and Operation),
Lifting (Description and Operation).
2. Disconnect the power steering fluid cooler
quick release couplings.
1. Press the power steering fluid cooler hose
quick release coupling locking tangs.
2. Disconnect the power steering fluid cooler
hose quick release coupling.
Allow the fluid to drain into a suitable
container.
3. Remove the radiator splash shield.
4. Lower the vehicle.
5. Remove the power steering fluid cooler.
I. Remove the retaining bolt.
Installation
1. N0TE:Make sure that the collar on the hose
is inserted fully into the quick release
coupling.
To install, reverse the removal procedure.
2. Fill and bleed the power steering system. For
additional information, refer to: (211 -00
Steering System
- General Information)
Power Steering System Filling (General
Procedures),
Power Steering System Bleeding (General
Procedures).
2006.0 Fiesta 1212006 G91972en
procarmanuals.com

Engine - 1.25L Duratec-1 6V (Sigma)ll.4L
Duratec-1 6V (Sigma)Il.GL Duratec-1 6V (Sigma)
SPECIFICATIONS
2006.0 Fiesta 1212006 GI 54208en
Ib-in
-
-
-
-
-
-
-
-
-
80
-
80
-
35
-
80
-
-
-
-
-
-
80
80
-
-
-
53
-
80
80
Ib-ft
41
35
66
35 35 18
30
18
35
-
20
-
15
-
21
-
11
-
-
13
-
35
-
-
11
15
15
-
-
-
-
Description
Engine front mount bracket to cylinder block
retaining bolts
Engine front mount retaining nuts and bolts
Engine rear mount center retaining nut
Engine rear mount outer retaining nuts
Engine support insulator retaining bolts Power steering line support bracket retaining bolts
Power steering line to power steering pump
Air conditioning
(AIC) compressor to cylinder block
retaining bolts
Generator to cylinder block top rear and lower
retaining bolts
Water pump retaining bolts
Water pump pulley retaining bolts
Oil pump to cylinder block retaining bolts
Oil pan to cylinder block retaining bolts
Oil level indicator tube bracket retaining bolt
Engine oil drain plug
Oil pump pickup pipe to cylinder block retaining
bolts
Oil pressure switch
Cylinder head bolts
Valve cover retaining bolts
Intake manifold to cylinder head retaining bolts
Exhaust manifold to cylinder head
Exhaust manifold to cylinder block
Camshaft position (CMP) sensor
Timing belt rear cover retaining bolts
Spark plugs Engine rear lifting eye retaining bolts
Coolant distribution housing retaining bolts
Ignition coil to coolant distribution housing
Camshaft bearing cap retaining bolts
Timing belt upper cover to cylinder block retaining
bolts
Timing belt lower cover to cylinder block retaining
bolts
Nm
55
48 90
48
48 25
40 25
47
9
27 9
20 4
28 9
15
a)
a)
18
a)
47 9
9
15
20
20
6
a)
9
9
procarmanuals.com

Engine - I .25L Duratec-1 6V (Sigma)llI4L
303-01 A-54 Duratec-1 6V (Sigma)/l .6L Duratec-1 6V (Sigma)
303-01 A-54
IN-VEHICLE REPAIR
Cylinder Head(21 163 0)
1 I Socket, Cylinder Head Bolts I
Discard the gasket and the nuts. (
Removerllnstaller, Hose
Clamp
303-397 (24-003)
I 24003 1 1 5. Raise and support the vehicle.
Removal
I I 1 For additional information, refer to: Lifting
(100-02 Jacking and Lifting, Description
1. Release the fuel system pressure.
Materials
For
additional information, refer to: Fuel
System Pressure Release (31 0-00 Fuel
System - General Information, General
Procedures). and
Operation).
2. Drain the
cooling system.
For
additional information, refer to: Cooling
System Draining, Filling and Bleeding
(303-03 Engine Cooling - 1.4L
Duratorq-TDCi (DV) Diesel, General 7. Remove the exhaust manifold lower heat
Procedures). shield left-hand retaining bolts.
3. Remove the camshaft.
Name
Specification
6. Using a suitable splint or wrap support the
For
additional information, refer to:
Camshafts
(303-01 Engine - 1.25L
Duratec-1 6V (Sigma)ll.4L Duratec-1 6V
(Sigma)ll.GL Duratec-1 6V (Sigma),
In-vehicle Repair).
Engine oil I WSS-M2C912-A1
4. Detach the exhaust flexible pipe from the
catalytic converter. exhaust
flexible pipe.
8. Remove the exhaust manifold lower heat
shield right-hand retaining bolts.
2006.0 Fiesta 1212006 GI 83740en
procarmanuals.com

Engine - 1.25L Duratec-1 6V (Sigma)ll.4L
303-01 A-63 Duratec-1 6V (Sigma)/l.6L Duratec-1 6V (Sigma) 303-01 A-63
IN-VEHICLE REPAIR
23. Connect the brake booster vacuum line to 27. Install the
exhaust manifold lower heat
the intake manifold. shield
left-hand retaining bolts.
24. Raise and support the vehicle. 28.
N0TE:lnstall a
new flexible pipe gasket and
For
additional information, refer to: Lifting new
nuts.
(1 00-02 Jacking and Lifting, Description Attach the flexible pipe to the catalytic
and Operation). converter
25.
Install the intake manifold retaining bolt.
29. Remove the exhaust flexible pipe support.
26. Position the exhaust
manifold lower heat . 30, Install the camshaft.
shield and install the right-hand retaining
For additional information, refer to:
bolts. Camshafts (303-01 Engine
- 1.25L
Duratec-1 6V (Sigma)ll.4L Duratec-1 6V
(Sigma)ll.GL Duratec-1 6V (Sigma),
In-vehicle Repair).
31.
N0TE:lnstall a new oil filter.
Change the engine oil.
32. Fill and bleed the cooling system.
For
additional information, refer to: Cooling
System Draining, Filling and Bleeding
(303-03 Engine Cooling - 1.4L
Duratorq-TDCi (DV) Diesel, General
Procedures).
2006.0 Fiesta 1212006 GI 83740en
procarmanuals.com

Engine - 1.25L Duratec-1 6V (Sigma)lla4L
303-01 A-64 Duratec-1 6V (Sigma)ll .6L Duratec-1 6V (Sigma) 303-01 A-64
IN-VEHICLE REPAIR
Oil Pan(21 154 0)
Special Tool(s)
Adapter for 205-047
303-633 (2
1 -227)
1501 1
General Equipment
Slide Hammer
205-047 (1 5-0 1 1 )
I Five M8 x 20 mm studs I
Materials
Name
S~ecification
3m CAUTION:^^ order to prevent damage to
the sealing surfaces, only use the designated
special tool to remove the oil pan. Do not
use a chisel or a screwdriver for removal.
N0TE:Tighten the lock nut against the oil pan and
use several taps to release the oil pan from the
cylinder block.
Using the special tool, remove the oil pan.
Installation
1. CAUTIONS:
n~he oil pump gasket projects over the
cylinder block sealing surface and must not
Removal be damaged.
I. Raise and support the vehicle. For additional ADO not damage the rubber sealing surface
information, refer to Section 100-02 [Jacking of
the crankshaft rear oil seal carrier.
and Lifting].
I Using Loctite 7070, clean the engine cylinder
2. Drain the engine and remove the oil pan block and
oil pan mating faces.
retaining bolts.
1. Remove the oil drain plug. 2m ~CAUTION:T~~ crankcase may be
damaged
if sealant enters the blind holes. 2. Remove the oil pan retaining bolts.
I I Install five M8 x 20 mm studs into the blind
holes where shown.
2006.0 Fiesta 1212006 GI 83741 en
procarmanuals.com

Engine - 1.25L Duratec-1 6V (Sigma)ll.4L
303-01 A-65 Duratec-1 6V (Sigma)ll .6L Duratec-1 6V (Sigma) 303-01 A-65
IN-VEHICLE REPAIR
3. N0TE:lnstall the oil pan within ten minutes 5. N0TE:Check the oil drain plug seal for
of applying sealant and tighten the bolts damage
and install a new drain plug if
( I within a further 5 minutes. necessary.
Apply a 3-4 mm diameter bead of sealant to Install the oil drain plug.
the oil pan flange.
6. Fill the engine with engine oil.
4. N0TE:Align the oil pan flush with the
cylinder block at the transaxle end.
Install the oil pan.
Tighten the oil pan retaining bolts in the
sequence shown in two stages.
Stage
I : 10 Nm.
( I Stage2:20Nm.
Remove the studs and install retaining bolts.
2006.0 Fiesta 1212006 GI 83741 en
procarmanuals.com

303-01 A-I I1
Engine - 1.25L Duratec-1 6V (Sigma)ll.4L
Duratec-1 6V (Sigma)ll .6L Duratec-1 6V (Sigma) 303-01 A-I I1
ASSEMBLY
Install the oil pump pickup pipe.
12. Coat the crankshaft front seal lip with clean
engine oil.
13. N0TE:lnstall a new crankshaft front seal.
15. N0TE:Attach the oil pan within ten minutes
of applying sealant and tighten the bolts
within a further five minutes.
Apply a
3 to 4 mm diameter thick bead of
sealant to the oil pan flange.
rnrn ---34
1 + 1 !fl
f
ELE0013938 -
Using the special tool, install the crankshaft
front seal. 16. N0TE:Align the oil pan so that the cylinder
block is flush with the oil pan on the
14' ~CAUTION:T~~ crankcase may be
damaged
if sealant enters the blind holes.
Install five
M8 x 20 mm studs into the blind
holes as shown. flywheel
side.
Install the oil pan, loosely install the retaining
bolts.
Remove the studs and install retaining bolts.
Tighten the oil pan retaining bolts in the
sequence shown in two stages.
Stage I : 10 Nm.
Stage
2: 20 Nm.
17. N0TE:lnspect the oil pan drain plug seal
for damage. Install a new drain plug and
seal
if required.
2006.0 Fiesta i~12006 GI 54225en
procarmanuals.com

,303-01 B-6 Engine - 2.OL Duratec-HE (M14) 303-01 B-6
SPECIFICATIONS
I Description I Nm' I Ib-ft I Ib-in I
Evaporative emission (EVAP) valve retaining
bracket retaining nut and bolt
Valve cover retaining bolts
I 10 I - I 89 I
Cylinder block blanking plug
Coolant pump pulley retaining bolts
Coolant pump retaining bolts
Oil level indicator and oil level indicator tube upper
retaining bolt
Oil level indicator and oil level indicator tube lower
retaining bolt 20
25
10
Oil pressure switch I 15 I 11 I - I
I Oil pan retaining bolts
15
18
-
-
-
89
I Crankshaft rear seal carrier retaining bolts I 10 I - I 89 I
Oil drain plug
Oil cooler to oil filter adaptor retaining bolt
I Flywheel retaining bolts I a) I - I - I
28
34
I Knock sensor retaining bolt I 20 I 15 I - I
Oil filter adaptor retaining bolts
Positive crankcase ventilation housing retaining
bolts
I Thermostat housing retaining bolts I 10 I - I 89 I
21
25
I Oil pump retaining bolts I a) I - I - I
-
-
25
10
I Oil pump sprocket retaining bolt I 25 I 18 I - I
18
-
-
89
Oil pump chain guide retaining bolts
Oil pump chain tensioner retaining bolt
I Crankshaft position sensor retaining bolts I 7 I - I 62 I
Timing chain guide retaining bolts
Timing chain tensioner retaining bolts
I Accessory drive belt idler pulley retaining bolt I 25 I 18 I - I
10
10
I Intake manifold retaining bolts I 18 I 13 I - I
10
10
I Transaxle left-hand retaining bolts I 44 I 32 I - I
-
-
I Transaxle right-hand retaining bolts I 44 I 32 I - I
89
89
-
-
89
89
Transaxle lower retaining bolts
Halfshaft center bearing carrier retaining bolts
I Lower arm ball joint retaining bolt I 48 I 35 I - I
Intermediate shaft bearing cap retaining nuts
2006.0 Fiesta 1212006 G451278en
40
48
25 30
35 -
-
18 -
procarmanuals.com