2007 FORD FIESTA Air con

303-01 B-27 Engine - 2.OL Duratec-HE (M14) 303-01 B-27
IN-VEHICLE REPAIR
4. Detach the positive crankcase ventilation 7. Remove the EVAP valve bracket.
(PCV) hose from the valve cover.
8. Using the special tool, disconnect the spark
5. Disconnect the camshaft position sensor plug electrical
connectors.
(CMP sensor) electrical connector.
6. Remove the air cleaner retainer.
9. Using the special tool, remove the spark
plugs.
2006.0 Fiesta 1212006 G451288en
procarmanuals.com

303-01 B-28 Engine - 2.OL Duratec-HE (M14) 303-01 B-28
IN-VEHICLE REPAIR
10. Remove the valve cover.
11. Remove the drive belt.
For additional information, refer to:
Accessory Drive Belt
- 2.OL Duratec-HE
(M14) (303-05 Accessory Drive, Removal
and Installation).
12.
N0TE:Only rotate the crankshaft in the
normal direction of rotation.
Rotate the crankshaft until piston no.
1 is
approx. 45 degrees before TDC. Using
the special tool, remove the crankshaft
pulley.
14. Remove the crankshaft front seal.
For additional information, refer to:
Crankshaft Front Seal (303-01 Engine
-
2.OL Duratec-HE (M14), Invehicle Repair).
15. Remove the front friction washer (engine
shown removed for clarity).
. Discard the friction washer.
16. N0TE:Do not damage the inner constant
13.
N0TE:Do not discard the crankshaft pulley velocity
(CV) joint boot.
bolt. Pull the inner CV joint boot off the
intermediate shaft.
2006.0 Fiesta 1212006 G451288en
procarmanuals.com

303-01 B-29 Engine - 2.OL Duratec-HE (M14) 303-01 B-29
IN-VEHICLE REPAIR
Remove and discard the CV joint boot clamp. 5. Install the special tool.
Installation 6. Raise the vehicle. For additional information,
refer to: (1 00-02 Jacking and Lifting)
1. N0TE:lnstall a new front friction washer.
Jacking (Description and Operation),
Install the front friction washer (engine
Lifting (Description and Operation).
shown removed for clarity).
7. Remove the cylinder block lower blanking
plug and install the special tool.
2. Install the crankshaft front seal.
For additional information, refer to:
8. N0TE:Only rotate the crankshaft in the
Crankshaft Front Seal (303-01 Engine - 2.OL normal direction of rotation.
Duratec-HE (M14), In-vehicle Repair).
Rotate the crankshaft using the crankshaft
3. Lower the vehicle.
pulley bolt until the crankshaft contacts the
4. N0TE:Only rotate the camshafts in the special
tool.
normal direction of rotation.
Carefully rotate the camshafts using a
spanner until the cams of cylinder no. 4 are
positioned at the valve overlap.
2006.0 Fiesta 1212006
procarmanuals.com

303-01 B-32 Engine - 2.OL Duratec-HE (M14) 303-01 B-32
IN-VEHICLE REPAIR
24. Raise the vehicle. For additional N0TE:Make sure that the contact surface for the
information, refer to: (100-02 Jacking and CV joint boot on the intermediate shaft is clean. ,
Lifting)
Slide the inner CV joint boot onto the
Jacking (Description and Operation),
intermediate shaft. (..
Lifting (Description and Operation). Use a suitable screwdriver under the boot to
25. Remove the M6 x 18 mm bolt. allow air to escape.
26. Remove the special tool. 29. N0TE:lnstall a
new boot clamp.
Using a suitable grip wrench, install the inner
CV joint boot clamp.
27. Install the cylinder block lower blanking
plug.
30. N0TE:When installing a new engine front
cover, the crankshaft position sensor
(CKP
sensor) must be aligned using the tool
supplied.
28.
N0TE:Do not damage the boot of the inner
CV joint. Align
the
CKP sensor (engine shown
removed for clarity).
1. Loosen the CKP sensor bolts.
2006.0 Fiesta 1212006 G451288en
procarmanuals.com

303-01 B-33 Engine - 2.OL Duratec-HE (M14) 303-01 B-33
IN-VEHICLE REPAIR
2. Insert the tool supplied so that it engages 34. N0TE:lf necessary, install a new valve
with the teeth of the crankshaft pulley. cover gasket.
31. Install the CKP sensor (engine shown
removed for clarity).
1. Install the CKP sensor bolts.
2. Remove the tool.
Install the valve cover.
Tighten the bolts in the sequence shown.
35. Using the special tool, install the spark
plugs.
. Install the drive belt.
36. Using the special tool, connect the spark
For additional information, refer to:
plug connectors.
Accessory Drive Belt
- 2.OL Duratec-HE
(M14) (303-05 Accessory Drive, Removal
and Installation).
33. Apply sealant thinly on the areas shown.
-- - -- -
2006.0 Fiesta 1212006 G451288en
procarmanuals.com

303-01 B-34 Engine - 2.OL Duratec-HE (M14) 303-01 B-34
IN-VEHICLE REPAIR
37. Install the EVAP valve bracket. 40. Attach the positive crankcase ventilation
(PCV) hose to the valve cover.
/- r.
38. Install the air cleaner retainer.
41. Attach the engine wiring harness to the
valve cover.
1. Clip on the engine wiring harness at the
intake pipe.
2. Clip on the engine wiring harness bracket at
the intake pipe.
3. Install the air cleaner retainer.
4. Connect the power. steering fluid return line
to the retaining clip.
42. Install the air cleaner.
For additional information, refer to: Air
Cleaner
- 2.OL Duratec-HE (M14) (303-12
Intake Air Distribution and Filtering,
Removal and Installation).
43. Connect the battery ground cable.
For additional information, refer to: Battery
Disconnect
(414-01 Battery, Mounting and
Cables, General Procedures).
2006.0 Fiesta 1212006 G451288en
procarmanuals.com

303-01 B-39 Engine - 2.OL Duratec-HE (M14) 303-01 B-39
IN-VEHICLE REPAIR
Special Tool(s)
I I Universal Flange Holding I
General Equipment
15030A
1~6 x 18 mm bolt I
Wrench
205-072
Materials
Name Specification
Removal
Hypoid Gear Oil
Silicone Sealant
1. Disconnect the battery ground cable.
SQM-2C9002-AA
WSE-M4G323-A4
For additional information, refer to: Battery
Disconnect
(414-01 Battery, Mounting and
Cables, General Procedures).
2. Remove the air cleaner.
For additional information, refer to: Air
Cleaner
- 2.OL Duratec-HE (M14) (303-12
Intake Air Distribution and Filtering,
Removal and Installation).
3. Detach the engine wiring harness from the
valve cover.
1. Unclip the power steering return line from the
engine wiring harness bracket.
2. Remove the air cleaner retaining bracket.
3. Unclip the engine wiring harness bracket
from the intake manifold.
4. Unclip the engine wiring harness from the
intake manifold.
4. Remove the positive crankshaft ventilation
(PCV) hose.
2006.0 Fiesta 1212006 G451293en
procarmanuals.com

303-01 B-40 Engine - 2.OL Duratec-HE (M14) 303-01 B-40
IN-VEHICLE
REPAIR
5. Disconnect the camshaft position (CMP) 8. Using the special tool, disconnect the spark
sensor electrical connector.
plug electrical connectors.
1.
6. Remove the air cleaner retaining bracket. 9. Using the special tool, remove the spark
plugs.
7. Remove the evaporative emission (EVAP)
valve support bracket.
10. Remove the valve cover.
11. Remove the accessory drive belt.
For additional information, refer to:
Accessory Drive Belt
- 2.OL Duratec-HE
(M14) (303-05 Accessory Drive, Removal
and Installation).
c
2006.0 Fiesta la2006 G451293en
procarmanuals.com