2007 FORD FIESTA table

303-01 B-50 Engine - 2.OL Duratec-HE (M14) 303-01 B-50 -
IN-VEHICLE REPAIR
8. Drain the engine. 12. Remove the engine front cover lower
Allow the oil to drain into a suitable container. retaining bolts. //
9. N0TE:lnspect the oil pan drain plug seal for
damage. Install a new drain plug and seal if
required.
lnstall the drain plug.
10. Loosen the transaxle right-hand retaining
bolts approximately
10 mm.
11. Loosen the transaxle left-hand retaining
bolts approximately 10 mm. 13.
Remove the transaxle lower retaining bolts.
14. Slide back the transaxle approximately
8
mm.
15. Remove the oil pan retaining bolts.
2006.0 Fiesta 1212006 G451306en
procarmanuals.com

303-01 B-56 Engine - 2.OL Duratec-HE (M14) 303-01 B-56
IN-VEHICLE
REPAIR
Crankshaft Rear Seal(21 468 4)
Special Tool(s) Install the drain plug.
Materials Name
S~ecification
1 Cleaner I WSK-M2G342-A I
5. Remove the oil level indicator tube lower
retaining bolt.
- -
d 21 135
4 21 179
I Silicone Sealant I WSE-M4G323-A4 I
Locking Tool, Flywheel
303-254 (2 1 -1 35)
Separator, Oil Pan
303-428 (21 -1
79)
Removal
1. Remove the oil level indicator and oil level
indicator tube upper retaining bolt.
2. Remove the clutch disc and pressure plate.
For additional information, refer to: Clutch
Disc and Pressure Plate
(308-01 Clutch,
Removal and Installation).
3. Drain the engine.
Allow the oil to drain into a suitable container.
4. N0TE:lnspect the oil pan drain plug seal for
damage. Install a new drain plug and seal
if
required.
6. Using the special tool, lock the flywheel in
position.
7. Remove the flywheel.
2006.0 Fiesta 1212006 G451307en
procarmanuals.com

303-01 B-64 Engine - 2.OL Duratec-HE (M14) 303-01 B-64
IN-VEHICLE REPAIR
Exhaust Manifold
1. Remove the air cleaner.
For additional information, refer to: Air
Cleaner
- 2.OL Duratec-HE (M14) (303-12
Intake Air Distribution and Filtering,
Removal and Installation). 2.
Remove the components in the order
indicated in the following
illustration(s) and
table(s).
2006.0 Fiesta 1212006 G451285en
Item Description Description
bolts 1
2
See Removal Detail
Exhaust manifold upper heat shield
Exhaust manifold lower heat shield
procarmanuals.com

303-01 B-67 Engine - 2.OL Duratec-HE (M14) 303-01 B-67
IN-VEHICLE REPAIR
Timing Chain(21 314 0) ,
Removal 4. Remove the timing chain guides.
1. Remove the engine front cover.
For additional information, refer to Engine
Front Cover
- in this section.
2. Detension the timing chain.
1. Unlock the timing chain tensioner ratchet.
2. Apply pressure to the timing chain guide.
3. Fix the timing chain tensioner with a suitable
pin punch.
3. N0TE:Hold the camshafts by the hexagon
with an open-ended wrench to stop them
from rotating.
Loosen the camshaft sprocket retaining
5. Remove the timing chain tensioner.
bolts.
Installation
1. Install the timing chain tensioner.
--
2006.0 Fiesta 1212006 G323910en
procarmanuals.com

303-01 B-74 Engine - 2.OL Duratec-HE (M14) 303-01 B-74
REMOVAL
Engine
Special Tool(s)
I I Remover, Power Steering I
I I Removerllnstaller, Hose
General Equipment
I Workshop table I
I Engine hoist I
I Securing straps I
Removal
A WARNING:Do not smoke or carry lighted
tobacco or open flame of any type when
working on or near any fuel related
components. Highly flammable vapors are
always present and may ignite. Failure to
follow these instructions may result in
personal injury.
1. Remove the air cleaner. c.
For additional information, refer to: Air
Cleaner
- 2.OL Duratec-HE (M14) (30312
Intake Air Distribution and Filtering,
Removal and Installation).
2. Remove the battery tray.
For additional information, refer to: Battery
Tray
- 2.OL Duratec-HE (M14) (414-01
Battery, Mounting and Cables, Removal
and Installation).
3. Loosen the strut and spring assembly top
mount nuts by three turns on both sides.
4. Remove the right-hand
headlamp assembly.
For additional information, refer to:
Headlamp Assembly (41 7-01 Exterior
Lighting, Removal and Installation).
5. Remove the accessory drive belt.
For additional information, refer to:
Accessory Drive Belt
- 2.OL Duratec-HE
(M14) (303-05 Accessory Drive, Removal
and Installation).
6. Drain the cooling system.
For additional information, refer to: Cooling
System Draining, Filling and Bleeding
(303-03 Engine Cooling
- 2.OL Duratec-HE
(M14), General Procedures).
7. Detach the exhaust flexible pipe from the
exhaust manifold.
For additional information, refer to: Exhaust
Flexible Pipe
- 2.OL Duratec-HE (M14)
(309-00 Exhaust System, Removal and
Installation).
2006.0 Fiesta 1212006 G451290en
procarmanuals.com

303-01 B-77 Engine - 2.OL Duratec-HE (M14) 303-01 B-77
REMOVAL
21. Disconnect the reversing lamp switch Detach the steering gear to power steering
electrical connector. fluid
reservoir return line support bracket
from the generator.
22m CAUTION:^^ brake fluid is spilt on the 25s Using the special tool, disconnect the paintwork, the affected area must be
immediately washed down with cold water. steering
gear to power steering fluid
reservoir return line from the power
Disconnect the clutch slave cylinder supply
steering fluid reservoir.
line.
Remove the spring clip. Allow
the power steering fluid to drain into a
suitable container.
23. Disconnect the air conditioning low 26. Remove the power steering fluid reservoir.
pressure switch connector.
24. N0TE:Note the position of the steering gear 27m &AUTION:C~~ the power steering fluid
to power steering fluid reservoir return line reservoir
to prevent power steering fluid
support bracket to aid installation. loss
or dirt ingress.
2006.0 Fiesta 12/2006 G451290en
procarmanuals.com

303-01 B-79 Engine - 2.OL Duratec-HE (M14) 303-01 B-79
REMOVAL
34. Detach the powertrain control module 37. CAUTIONS:
(PCM) support bracket from the side
i member. A~he inner CV joint must not be bent
more than
23 degrees. The outer CV joint
35m ACAUTION:P~~~~~~ the ball joint seal
using
a soft cloth to prevent damage.
Detach the lower arm ball joint from the
wheel knuckle on both sides.
Remove the heat shield.
must not be bent more than 45 degrees.
A~ake sure the halfshaft seal is not
damaged.
Aplug the transaxle to prevent oil loss or
dirt ingress.
Remove the halfshaft and intermediate shaft
assembly.
Allow the oil to drain into a suitable container.
38. CAUTIONS:
Asupport the halfshaft. The inner joint
must not be bent more than
I8 degrees.
The outer joint must not be bent more than
45 degrees.
ADO not damage the halfshaft seal.
N0TE:Plug the transaxle to prevent oil loss or dirt
ingress.
36. Remove the intermediate shaft center
bearing cap. Remove
the left-hand halfshaft.
Discard the bearing cap and retaining nuts.
Remove the intermediate shaft center
bearing heat shield (if equipped).
2006.0 Fiesta 1212006 G451290en
procarmanuals.com

303-01 B-80 Engine - 2.OL Duratec-HE (M14) 303-01 B-80
REMOVAL
39. Remove the gearshift cables cover. 42. Detach the NC compressor from the
cylinder block and position
it to one side. /-
40. Detach the gearshift cables from the
transaxle. 43.
Remove the engine support insulator.
1. Detach the gearshift cables and the selector
cable from the selector levers.
2. Turn the abutment sleeve clockwise and
detach the cables from the bracket.
44. N0TE:Use securing straps to secure the
engine and the transaxle on the workshop
table.
Position the workshop table under the
41. Disconnect the NC high pressure switch
vehicle and carefully lower the vehicle, until
electrical connector.
the engine and transaxle assembly is in the
correct position to remove the engine
mounts.
45. Remove the engine front mount.
2006.0 Fiesta 1212006 G451290en
procarmanuals.com