2007 FORD FIESTA table

308-03-60 Manual Transmission/Transaxle 308-03-60
ASSEMBLY
41. lnstall the gearshift cable bracket. 2. lnstall the retaining pin.
42. N0TE:lnstall a new snap ring. 45m &AUTION:U~~~~ suitable adhesive tape,
Install the gearshift lever. cover
the input shaft splines to prevent
damage to the input shaft oil seal.
1. lnstall the snap ring.
2. lnstall the protective cap (if equipped). Position
the input shaft oil seal.
TIE
43. lnstall the selector mechanism cover. 46m ~CAUTION:DO not apply grease on any
parts of the clutch slave cylinder.
lnstall the clutch slave cylinder.
44. lnstall the vehicle speed sensor (VSS) (if
equipped).
1. Push in the VSS.
Tighten the bolts evenly. In doing so, press
the input shaft oil seal into the transmission
housing.
2006.0 Fiesta 1212006 G23119en
procarmanuals.com

308-03-62 Manual Transmission/'rransaxle 308-03-62
INSTALLATION
Transaxle - 1.25L Duratec-I 6V (Sigma)/Im4L Duratec-1 6V
(Sigma)/l .6L Duratec-1 6V (Sigma)(l 6 1 14 0)
Special Tool(s)
Support Bar, Engine
303-290A (21
-1 40A)
Adapter for 303-290A 303-290-0
1 (2 1 -1 40-0 1 )
Adapter for 303-290A
303-290-02 (21
-1 40-02)
21 14002
I I I
General Equipment
Retaining strap
I Transmission jack I
Materials
Name Specification
Installation
Manual transmission
1 fluid
All vehicles
I. CAUTIONS:
WSD-M2C200-C
&se suitable retaining straps to secure
the transaxle on the transmission jack.
A~ake sure that the two locating dowels
are installed.
Using a suitable transmission jack, install
the transaxle.
2. Install the transaxle right-hand retaining
bolts.
3. Install the transaxle lower retaining bolts.
-- -- -
2006.0 Fiesta 1212006 GI 13293en
procarmanuals.com

308=03=69 Manual Transmission/Transaxle 308=03=69
INSTALLATION
Transaxle - 2.OL Duratec-HE (M14)(16 11 4 0)
i
Special Tool(s)
I I Support Bar, Engine
Adapter for 303-290A
303-290-01 (21 -1 40-01
)
General Equipment , I
@ 21 14005
21 14006
I Retaining strap I
Adapter for 303-290A
303-290-05A (2 1
- 1 40-05A)
Adapter for 303-290A
303-290-06 (21 -1 40-06)
I Transmission jack I
Materials
Name Specification
Installation
1. CAUTIONS:
A~se suitable retaining straps to secure
the transaxle on the transmission jack.
A~ake sure that the two locating dowels
are installed.
Using a suitable transmission jack, install
the transaxle.
Manual transmission
1 fluid
2. Install the transaxle right-hand retaining
bolts.
WSD-M2C200-C
2006.0 Fiesta 1212006 G453417en
procarmanuals.com

308-03-71 Manual Transmission/Transaxle 308-03-71
INSTALLATION
Attach the exhaust flexible pipe to the 15.
Remove the support wrap or suitable splint
catalytic converter. from
the exhaust flexible pipe.
i
3m ACAUTION:~~ brake fluid is spilt on the 16. lnstall the right-hand halfshaft.
paintwork, the affected area must be For additional information,
refer to: Front
immediately washed down with cold water. Halfshaft
RH (205-04 Front Drive
N0TE:Make sure the spring clip is correctly seated. Halfshafts, Removal and Installation).
Connect the clutch slave cylinder supply
17. lnstall the left-hand halfshaft.
line. For additional information,
refer to: Front
lnstall the spring clip. Halfshaft LH (205-04 Front Drive
Halfshafts, Removal and Installation).
18. lnstall the engine support insulator.
14. Raise and support the vehicle. For
additional information, refer to: (I
00-02
Jacking and Lifting)
19. Install the accessory drive belt cover.
Jacking (Description and Operation),
Lifting (Description and Operation).
2006.0 Fiesta 1212006 G453417en
procarmanuals.com

309-00-6 Exhaust System 309-00-6
REMOVAL AND INSTALLATION
Catalytic Converter - 2.OL Duratec-HE (M14)
/'
Materials Support
the exhaust flexible pipe with a (,
support wrap or splint.
Name Specification
1 Grease I SA-M 1 C9107-A I --
N0TE:lf installing a new catalytic converter to the
original exhaust system, a new muffler and tailpipe
assembly must also be installed.
1. Raise and support the vehicle. For additional
information, refer to:
(1 00-02 Jacking and
Lifting)
Jacking (Description and Operation),
Lifting (Description and Operation).
*' CAUTION:^^^^ bending of the exhaust
flexible pipe may cause damage resulting in 3. Remove the components in the order failure.
indicated in the following illustration(s) and
table(s).
Item Description Item Description
2006.0 Fiesta 1212006 G453448en
2
3
See Removal Detail
See Installation Detail
1
Catalytic converter monitor sensor
electrical connector
Catalytic converter monitor sensor
Exhaust hanger insulator
4 Catalytic converter to exhaust flexible pipe
retaining nuts
procarmanuals.com

309=00=8 Exhaust System 309m00m8
REMOVAL AND INSTALLATION
Exhaust Flexible Pipe - 2.OL Duratec-HE (M14)
Materials 1. Raise and support the vehicle. For additional \.. ;
information, refer to: (I 00-02 Jacking and
Name Specification
I 1 Liftinn)
Lifting (Description and Operation).
Grease I SA-M 1 C9 1 07-A
2. Remove the components in the order
indicated in the following
illustration(s) and
table(s).
-I
2006.0 Fiesta 1212006 G458157en
Jacking (Description and Operation),
procarmanuals.com

31 0-00-7 Fuel System - General Information 31 0-00-7
GENERAL PROCEDURES
10. Using a suitable Flat-bladed screwdriver 2. Disconnect the fuel line from the fuel filter.
release the fuel line quick release coupling
( secondary locking tang.
Connect
11. Operate the fuel line quick release coupling WARNINGS:
primary locking tang.
Push the fuel line quick release coupling
primary locking tang into from the fuel line
quick release coupling.
12. Disconnect the fuel line from the fuel line
quick release coupling.
13. Disconnect the fuel line from the fuel filter.
1 . Press the collar into the connector body.
Do not carry lighted tobacco or open flame
of any type when working on or near any
fuel related components. Highly flammable
vapors are always present and can ignite.
Failure to follow these instructions may
result in personal injury.
A This procedure involves fuel handling. Be
prepared for fuel spillage at all times and
always observe fuel handling precautions.
Failure to follow these instructions may
result in personal injury.
A CAUTI0N:Fuel injection equipment is
manufactured to very precise tolerances
and fine clearances.
It is therefore essential
that absolute cleanliness is observed when
working with these components. Always
install blanking plugs to any open orifices
or lines.
N0TE:Fuel supply line connectors are white or are
identified by a white band. Fuel return line
connectors are red or are identified by a red band.
1. Push the connector on to the fuel filter.
2006.0 Fiesta 1212006 GI 81 92en
procarmanuals.com

31 0-01 -7 Fuel Tank and Lines 31 0-01 -7
REMOVAL AND INSTALLATION
7. Remove the exhaust system heat shield. Using
a suitable transmission jack, support
/ the fuel tank.
*' Ac*u~~oN:when removing the fuel tank 10. Remove the fuel tank support strap rear vent and filler pipes, do not use any sharp
edge tools to lever off the pipes. Failure to retaining bolts.
follow this instruction may cause damage to
the pipes.
N0TE:Make note of the positions of the retaining
clamps to make sure they are positioned in exactly
the same positions when installing.
Disconnect the fuel tank filler pipe and the
fuel tank vent pipe from the fuel tank.
I I Discard the retaining clamps.
9m ACAUTION:~~~ a suitable packing material
to prevent damage to the underside of the
fuel tank.
11. N0TE:Make note of the positions of the
support straps to make sure they are
positioned in exactly the same positions
when installing (left-hand over right-hand).
Remove the fuel tank support straps.
2006.0 Fiesta 1212006 GI 89084en
procarmanuals.com