2007 FORD FIESTA power steering

Engine - I .25L Duratec-1 6V (Sigma)llm4L
Duratec-1 6V (Sigma)/l .6L Duratec-1 6V (Sigma)
IN-VEHICLE REPAIR
4. Remove the crankshaft pulley. 8. Detach the power steering fluid reservoir
from the bracket and position
it to one side. f
5. Remove the coolant pump pulley.
6. Remove the timing belt cover retaining bolts.
9. Detach the coolant expansion tank from the
bracket and position
it to one side.
1. Remove the timing belt upper cover retaining
bolts. 10. Disconnect the generator electrical
connector.
2. Remove the timing belt lower cover retaining
bolts.
Remove the lower cover.
7. Lower the vehicle.
11. Detach the generator from the engine.
1. Loosen the bolt.
2. Remove the bolt.
2006.0 Fiesta IZIZOO~ GI 83738en
procarmanuals.com

Engine - 1.25L Duratec-I 6V (Sigma)llm4L
303-01 A-46
Duratec-1 6V (Sigma)ll .6L Duratec-1 6V (Sigma) 303-01 A-46
IN-VEHICLE REPAIR
34. Tighten the coolant pump pulley retaining
bolts.
35. Install the valve cover.
For additional information, refer to: Valve
Cover
(303-01A Engine - 1.25L
Duratec-1 6V (Sigma)ll.4L Duratec-1 6V
(Sigma)ll .6L Duratec-1 6V (Sigma),
In-vehicle Repair).
36. Attach the power steering fluid reservoir to
the bracket.
37. Attach the coolant expansion tank to the
bracket.
2006.0 Fiesta 1212006 GI 83738en
procarmanuals.com

Engine - 1.25L Duratec-1 6V (Sigma)ll.4L
303-01 A-48 Duratec-1 6V (Sigma)/l .6L Duratec-1 6V (Sigma)
303-01 A-48
IN-VEHICLE REPAIR
7. Remove the engine support insulator
retaining bolt.
8. Remove the exhaust manifold lower heat
shield left-hand retaining bolts. 11.
Disconnect the heated oxygen
(H02S)
sensor electrical connector. //' '
12. Disconnect the catalyst monitor sensor
electrical connector.
9. Remove the exhaust manifold lower heat
13. Detach the power steering line support
shield right-hand retaining bolts.
bracket from the cylinder head.
Remove the lower heat shield.
10. Lower the vehicle.
2006.0 Fiesta 1212006 GI 83739en
procarmanuals.com

Engine - 1.25L Duratec-1 6V (Sigma)ll.4L
Duratec-1 6V (Sigma)Il.GL Duratec-I 6V (Sigma)
IN-VEHICLE REPAIR
14. Detach the power steering fluid reservoir Discard the nuts.
from the bracket and position it to one side. /
15. Detach the coolant expansion tank from
the bracket and position it to one side.
16. Install the special tools.
17. Remove the engine front mount.
18. Using the special tools lower the engine.
19. Remove the exhaust manifold upper heat
shield.
20. Remove the exhaust manifold retaining
bolts and the nuts.
2006.0 Fiesta 1212006 GI 83739en
procarmanuals.com

Engine - 1.25L Duratec-1 6V (Sigma)ll14L
Duratec-1 6V (Sigma)/l .6L Duratec-1 6V (Sigma)
IN-VEHICLE REPAIR
7. Using the special tools, raise the engine. 10. Attach the coolant expansion tank to the
bracket.
,
8. N0TE:lnstall new engine front mount
retaining nuts.
11. Attach the power steering fluid reservoir to
Install the engine front mount. the
bracket.
9. Remove the special tools. 12. Attach the power steering line bracket to
the cylinder head.
2006.0 Fiesta 1212006 GI 83739en
procarmanuals.com

Engine - 1.25L Duratec-1 6V (Sigma)ll.4L
Duratec-1 6V (Sigma)llm6L Duratec-1 6V (Sigma)
IN-VEHICLE REPAIR
21. Using the special tool, disconnect the 24.
Disconnect the electronic ignition (El) coil
/ coolant hose from the coolant distribution electrical connector.
I I assembly.
25. Disconnect the heated oxygen
(H02S)
22. Using the special tool, detach the degas sensor electrical connector.
hose from the cylinder head.
Detach the electrical connector from the
Using the special tool, detach the degas hose bracket.
from the cylinder head.
26. Detach the power steering line bracket from
23. Disconnect the engine coolant temperature the
cylinder head.
(ECT) electrical connector.
2006.0 Fiesta 1212006 GI 83740en
procarmanuals.com

Engine - 1.25L Duratec-1 6V (Sigma)llm4L
Duratec-1 6V (Sigma)ll .6L Duratec-1 6V (Sigma)
IN-VEHICLE REPAIR
Stage 1 : 20 Nm.
Stage2: 55 Nm.
8. Attach the power steering line bracket to the
cylinder head.
TIE0030694
6. Tighten the exhaust manifold lower retaining g, Connect the heated oxygen (H02S) sensor bolts. electrical connector.
Attach the electrical connector to the bracket.
7. Install the exhaust manifold upper heat
shield. 10. Connect the electronic ignition (El) coil
electrical connector.
2006.0 Fiesta 1212006 GI 83740en
procarmanuals.com

Engine - I .25L Duratec-1 6V (Sigma)ll.4L
Duratec-1 6V (Sigma)ll .6L Duratec-1 6V (Sigma)
REMOVAL
7. Disconnect the fuel return line quick release 10. Detach the power steering fluid reservoir
coupling. from
the bracket and position
it to one side.
i For additional information, refer to: Quick
Release Coupling
(310-00 Fuel System -
General Information, General Procedures).
8. Disconnect the fuel supply line quick release
coupling.
For additional information, refer to: Quick
Release Coupling
(310-00 Fuel System -
General Information, General Procedures).
9. Detach the fuel line and the degas line from
the intake manifold.
Remove the cable tie. 11.
Using
the special tool, disconnect the
degas hose from the cylinder head.
12. Detach the coolant expansion tank from
the bracket and position
it to one side.
2006.0 Fiesta 1212006 GI 131 63en
procarmanuals.com