Page 39 of 314
SET-UP MENU
The “Set-up Menu” enables to perform the following
adjustments and/or settings using the control buttons
(see previous pages):
❒SPEED LIMIT
❒AUTOMATIC HEADLIGHT DAYLIGHT SENSOR
(where provided)
❒TRIP B ON/OFF
❒SET CLOCK
❒CLOCK MODE
❒SET DATE
❒SPEEDLOCK
❒INDEPENDENT BOOT
❒DRIVER’S DOOR UNLOCKING❒DISTANCE UNIT
❒CONSUMPTION UNIT
❒TEMPERATURE UNIT (where required)
❒LANGUAGE
❒BUZZER VOLUME
❒BUTTON VOLUME
❒S.B.R. (Seat Belt Reminder) BUZZER
REACTIVATION (*)
❒SERVICE
❒EXIT MENU
38
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
(*) This function can be displayed only after Fiat Dealership has deactivated the S.B.R. system.
Page 70 of 314

69
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
F0H0041m
F0H0042m
SEAT ADJUSTMENT
FRONT SEATS
Moving the seat backwards or forwards
Lift the lever (A) and push the seat forwards or backwards: in the driving
position the arms should rest on the rim of the steering wheel.
Always check that the seat is firmly locked in the runners by trying to
move it back and forth.
Seat height adjustment (driver’s side) (where provided)
Move repeatedly lever (B) upwards or downwards to achieve the
required height.
IMPORTANT Adjustment must be carried out only seated in the driver’s
seat with the car at a standstill.
Back rest angle adjustment
Move lever (D) as shown by the arrow, set the back rest in the required
position, then release the lever.
Lumbar adjustment (where provided)
Turn knob (C) clockwise or counterclockwise to increase or decrease
lumbar adjustment.
After adjustments, always check that the seat is firmly locked in the runners.WARNING
Page 71 of 314
70
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
Armrest adjustment (where provided)
To use the armrest, move it from position 1 to position 2.
Setting the passenger’s seat to “table” configuration
Set the armrest (where provided) in vertical position.
From driver’s seat or rear seats, move the lever (A) as shown by the
arrow, tilt the back rest on the cushion, then release the lever. In this
position the back rest can be used like a table.
Setting the driver’s seat to “table” configuration
Remove the head restraint completely (see “Head restraint removal” in
section “Head restraints”) then follow the previously described procedure.
Seat warming (where provided)
To switch on/off seat warming on driver’s side press button (B), press
button (C) for the passenger’s side.
The led on the button will light up when the function is on.
F0H0043m
F0H0044m
F0H0045mF0H0046m
Page 138 of 314

137
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
F0H0117m
F0H0118m
F0H0119m
To adjust the headlight slant
To adjust the headlight slant operate buttons
and Òlocated on the
dashboard.
The display provides the visual indication of the positions during the
adjustment operation.
Position 0 - one or two people occupying the front seats.
Position 1 - five people.
Position 2 - five people + load in the boot.
Position 3 - driver + maximum permissible load stowed in the boot.
IMPORTANT Check beam aiming every time the load carried changes.
HEADLIGHT ADJUSTMENT ABROAD
The dipped-beam headlights are adjusted for circulation in the country in
which the vehicle is marketed. In countries with opposite circulation, to
avoid glaring oncoming vehicles, it is necessary to cover the areas of the
headlight as shown below: this is done using non-transparent sticker tape.
Figures refer to passing from right-hand drive to left-hand drive.