2007 FIAT GRANDE PUNTO USB

38
New destination
The NEW DESTINATIONmenu al-
lows you to enter a destination in various
ways:
❒ADDRESS: set the address by choos-
ing a town/city centre or the required
street;
❒POINTS OF INTEREST: select a
point of interest from the relevant sub-
menu.
Address
Use this menu to enter the address of
your required destination, indicating the
country, the town/city, the name of the
road/street and the house number.
?
To enter an address using manual in-
teraction:
Activate the main Menu, select the
NAVIGATIONoption and then
press SRC/OKor
ß/MAIN.
Select the NEW DESTINATION
option by pressing SRC/OKor
ß/MAIN.
Select ADDRESSand then press
SRC/OKor
ß/MAIN.
}Or use voice interaction by pressing
‘and saying “Navigation”. Once
the system message has finished, say
“New destination” and then “Ad-
dress”.
Blue&Me™ Navstarts by asking
your to select the required country
name.
Before anything else, the system de-
termines which countries are pre-
loaded on your USB device. If the
maps for only one country are pre-
sent, this will be set as the destina-
tion country.Use the “
N” or “O” keys to select the
required country and press SRC/OKor
ß/MAINto confirm.
}Using voice interaction, say the re-
quired country. Blue&Me™ Nav
will ask you to confirm the select-
ed country by means of a voice
message.
Notes:
❒In order to select the country, the USB
device containing the maps must be in-
serted in the USB port on the car.
❒If several countries are loaded on your
USB device, Blue&Me™ Navwill
show a list of countries in alphabetical
order on the multifunction display. If
the system is able to detect the GPS po-
sition of the car, the country where you
are located will be shown at the head
of the list.
After selecting the country, Blue&Me™
Navwill ask you to enter the destination
town/city by means of the steering wheel
control and voice interaction.For road safety reasons, it is
only possible to enter a new
destination with the car at a stand-
still.
WARNING
603_83_390 Punto C3 GB 19-06-2007 11:21 Pagina 38

39
Procedure for entering destination
TOWN/CITY
The area of the control panel multifunc-
tion display you use to enter the town/city
name is made up as follows:
A- Blue&Me™ Navuses the firstrow
to tell you that you are currently in
town/city input mode.
B– The secondrow displays the char-
acters already entered into Blue&Me™
Nav, which are used to make up the des-
tination town/city name.
C– The thirdrow is used to display the
character selected using SRC/OKor
ß/MAIN.
D– The fourthrow is made up of two
parts: you may scroll through the charac-
ters shown on the left side of the display
using the “
N” key and those displayed on
the right part using the “O” key.Once you have entered two characters,
Blue&Me™ Navwill help you by dis-
playing only the letters that could poten-
tially be used to compose the final name
of the town/city according to the map in-
formation stored in your USB device.
Operation of steering wheel keys
during TOWN/CITY name input
❒KEY“N”
– Allows you to scroll through the
characters shown on the leftside
of the fourth row of the display.
– Once you have entered two char-
acters, if you press the “
N” key
once, you will be given the option
of deleting the last character en-
tered; press SRC/OKor
ß/MAIN
to delete.Press the “N” key
again to continue entering charac-
ters.
❒KEY“O”
– Allows you to scroll through the
characters shown on the rightside
of the fourth row of the display.
– Once you have entered two char-
acters, if you press the “
O” key
once, OK?will be displayed on the
third row of the display. This
prompts you to stop entering char-
acters and instead choose the
town/city name from a list. You are
only advised to use this option if the
name of the town/city shown on
the second row is the full name of
the required town/city. Press
SRC/OKor
ß/MAINto confirm.-
Press the “
O” key again to contin-
ue entering characters.
❒“&/ESC” KEY
– Press the
&/ESCkey to return to
the previous menu.
fig. 4F0M1032g
603_83_390 Punto C3 GB 19-06-2007 11:21 Pagina 39

41
After entering the destination Road/Street,
Blue&Me™ Navwill ask you if you wish
to enter a house numberor navigate to-
wards the address currently set. The avail-
able options are:
❒ENTER NUMBER
❒START NAVIGATION
?Using manual interaction:
Select the required option using the “
N”
or “O” keys and press SRC/OKor
ß/MAINto confirm.
}Or using voice interaction, say “En-
ter number” or “Start”.
If you choose Start navigation, the sys-
tem will display the full address and ask
you to confirm in order to begin naviga-
tion. If the address entered is ambiguous,
the system will prompt you to choose be-
tween the possible alternatives.
If you choose Enter number, you must
enter the house number of the chosen
destination address.
?
Proceed as follows to enter the
house number:
Scroll through the numbers in the fourth
row (see fig. 4) using the “
N” or “O”
keys until the required numbers are dis-
played on the third row. Press SRC/OK
or
ß/MAINto select the number. Pro-
ceed in the same way to select the fol-
lowing numbers until the full house num-
ber is displayed in the second row.
Press the “
N” key to delete the last num-
ber entered. The system will ask you to
confirm the deletion by pressing SRC/OK
or
ß/MAIN. If you are using voice inter-
action, press
‘and say “Delete”.
Press the “
O” key once to finish enter-
ing the house number displayed. The sys-
tem will ask you to confirm by pressing
SRC/OKor
ß/MAIN. If you are using
voice interaction, press ‘ and say “OK”.
Once you have entered the house num-
ber Blue&Me™ Navwill display the full
address and ask for confirmation in order
to begin navigation. If the address entered
is ambiguous, the system will prompt you
to choose between the possible alterna-
tives.Note
While entering the house number, both
numbers and letters are shown on the
fourthrow (see fig. 4) of the reconfig-
urable multifunction display; in the event
of future map software updates, these will
allow you to set particular types of num-
bering that require the use of alphanu-
merical characters.
Points of interest
This function gives you access to a file con-
taining information on the location of use-
ful destinations of general interest divided
by category (e.g.: hotels, restaurants,
chemists, airports, railway stations, au-
thorised workshops etc.).
To use this function, your USB device with
the preloaded map software must be con-
nected to the USB port on the car.
?
To select a Point of interest using
manual interaction:
Activate the main Menu, select the
NAVIGATIONoption and then
press SRC/OKor
ß/MAIN.
Select the option NEW DESTI-
NATIONby pressing SRC/OKor
ß/MAIN.
Select POINTS OF INTEREST
and press SRC/OKor
ß/MAINto
confirm.
603_83_390 Punto C3 GB 19-06-2007 11:21 Pagina 41

42
Blue&Me™ Navwill display a list of
available points of interest categories.
Choose the required category from those
stored in the map software on your USB
device using the “
N“ or “O“ device and
press SRC/OKor
ß/MAINto confirm.
Now Blue&Me™ Navwill prompt you
to choose between LOCAL POINTS
of interest or ELSEWHERE.
❒If you select LOCAL POINTSof in-
terest by pressing SRC/OKor
ß/MAIN, Blue&Me™ Navwill dis-
play a list of points of interest belong-
ing to the category selected previously
(e.g. restaurants), sorted according to
distance from your current location, in-
cluding distanceand name. Scroll
through the list using the “
N” or “O”
keys and press SRC/OKor
ß/MAIN
to select the point of interest.
❒If you select points of interestELSE-
WHERE Blue&Me™ Navwill ask
you to specify the point of interest
country and town/city, in the same way
as when entering an address.
Blue&Me™ Navwill display a list of
points of interest in the chosen cate-
gory in alphabetical order.
Scroll through the list using the “
N”
or “O” keys and press SRC/OKor
ß/MAINto select the point of inter-
est required.Note
If the point of interest selected using the
previous options has a telephone number
and your Bluetooth
®mobile phone is
connected to Blue&Me™ Nav, the sys-
tem will allow you to decide whether to
start navigating toward the chosen point
of interest or make a phone call. Select the
required option by pressing SRC/OKor
ß/MAIN.
}Or use voice interaction by press-
ing
‘and saying “Navigation”.
Once the system message has fin-
ished, say “New destination” and
then “Points of interest”.
Then say “List” e Blue&Me™ Nav
will provide you with a list of the available
categories. If you already know which of
the categories stored on your USB device
you require you may say it directly.
Refer to the “NAVIGATION VOICE
COMMANDS” section for a list of avail-
able categories.The system will ask you for confirmation,
say “Yes“ or press SRC/OKor
ß/MAIN. Otherwise say “No“.
Now Blue&Me™ Navwill prompt you
to choose between “local” points of in-
terest or “elsewhere” by means of voice
synthesis.
❒If you select “local”, Blue&Me™
Navwill display a list of points of in-
terest belonging to the category se-
lected previously (e.g. restaurants),
sorted according to distance from your
current location, including distance
and name.
Scroll through the list using the “
N” or
“O” keys and press SRC/OKor
ß/MAINto select the required point
of interest.
❒If you say “elsewhere” Blue&Me™
Navwill ask you to specify the point of
interest country and town/city, in the
same way as when entering an address.
Blue&Me™ Navwill display a list of
points of interest in the chosen cate-
gory in alphabetical order.
Scroll through the list using the “
N” or
“O” keys and press SRC/OKor
ß/MAINto select the point of inter-
est required.
603_83_390 Punto C3 GB 19-06-2007 11:21 Pagina 42

45
}Or with voice interaction, press ‘and say “Navigation”. Then, once
the system message has finished, say
“Recent destinations”.
Blue&Me™ Navwill show a list of
the latest destinations entered on
the multifunctional display.
Select the required destination by
saying “Forward” or “Back”. Say
“Start” to start navigation or
“Delete” to delete the displayed
destination.
If you wish to delete all the stored
destinations, say “Delete all” and
confirm the operation when
prompted by the system.
Note
In order to start navigating towards the
last destination selected, the USB device
containing the maps must be inserted in
the USB port on the car.Navigation settings
The NAVIGATION SETTINGSmenu
allows you to establish navigation options,
e.g. by indicating whether you want
Blue&Me™ Navto calculate the fastest
or shortest route or whether motorways
or ferries should be included in the route
calculation.
This menu may also be used to set your
preference for voice completion of the
destination by means of the DICTATE
DESTINATIONoption.
?
In order to access the navigation set-
tings, using manual interaction, pro-
ceed in the following way:
Activate the main Menu, select the
NAVIGATIONoption and then
press SRC/OKor
ß/MAIN.
Select the NAVIGATON SET-
TINGSmenu and press SRC/OK
or
ß/MAINto confirm.
}Or with voice interaction:
Press
‘and say “Navigation”.
Once you have heard the system
message, say “Navigation set-
tings”. Blue&Me™ Navwill dis-
play a list of the available options.
The available options are:
❒Type of Route
Use this option to tell Blue&Me™ Nav
whether you want the calculated route to
be FASTERor SHORTER.
?Using manual interaction, proceed
as follows:
Select the TYPE OF ROUTEop-
tion and then press SRC/OKor
ß/MAIN.
Select the required option using the
“
N” or “O” keys and press
SRC/OKor
ß/MAINto confirm.
}Or with voice interaction:
Press
‘and say “Type of route”.
Blue&Me™ Navwill tell you the
current setting using voice synthe-
sis and will ask you if you wish to
change it. Answer “Yes” to change
the option, “No” to maintain the
current setting.
For road safety reasons, it is
only possible to enter a new
destination with the car at a stand-
still.
WARNING
603_83_390 Punto C3 GB 19-06-2007 11:21 Pagina 45

5858
}
To set the GPRS code using voice
interaction, proceed as follows:
Press
‘, pronounce “Settings”
and then “Connection code”.
Blue&Me™ Navwill prompt “The
current GPRS connection code is
value. To change code say a number
from 1 to 9 or say “Default”. To dis-
able the connection code say “Dis-
able”. To change the code, say a
number from 1 to 9 or say “De-
fault”. To disable the connection
code say “Disable”. (In previous
text, valueis the GPRS connection
code set at that moment).
After setting the new connection
code, Blue&Me™ Navwill say
“The Connection Code is set to val-
ue” (here valuecorresponds to the
new GPRS code set). MEDIA PLAYER SETTINGS
Autoplay
When the Autoplay optionis on,
Blue&Me™ Navwill start to play the au-
dio files on your USB device as soon as you
turn the ignition key MAR. Once you ac-
tivate this option, the first time you use the
player, playback will start automatically.
The Autoplay optionshall be disabled
(when required) before connecting your
USB device to the USB port and building
or updating the media library.
?
To change Autoplay settingus-
ing manual interaction, proceed as
follows:
Open the Main Menu, select SET-
TINGS, MEDIA PLAYER, AU-
TOPLAYand then press SRC/OK
or
ß/MAIN.
To activate Autoplay, selectAU-
TOPLAY ONand press SRC/OK
or
ß/MAIN. To deactivate Auto-
play select AUTOPLAY OFFand
press SRC/OKor
ß/MAIN.
603_83_390 Punto C3 GB 19-06-2007 11:21 Pagina 58

5959
}
Or, using voice interaction:
Press
‘and pronounce “Auto-
play on” or “Autoplay off”.
Note
If you change the Autoplaysettings after
connecting the USB device, new setting
will be activated the next time you con-
nect a different USB device (or the same
USB device with updated track library).Shuffle
Use the Shuffleoption to change the
playback sequence. With Shuffleoption
on, Blue&Me™ Navwill play digital au-
dio files at random.
?
To change Shufflesetting using
manual interaction, proceed as fol-
lows:
Open the Main Menu, select SET-
TINGS, MEDIA PLAYER,
SHUFFLEand then press
SRC/OKor
ß/MAIN.
To activate the Shuffleoption, se-
lect SHUFFLE ONand press
SRC/OKor
ß/MAIN. To deacti-
vate it, select SHUFFLE OFFand
press SRC/OKor
ß/MAIN.
}
Or, using voice interaction:
Press
‘and pronounce “Shuffle
on” or “Shuffle off”.Loop
Use the Loopoption to repeat a track.
?
To activate the Loopoption using
manual interaction, proceed as fol-
lows:
Open the Main Menu, select SET-
TINGS, MEDIA PLAYER,
LOOPand then press SRC/ OK
or
ß/MAIN.
To activate the Loopoption, select
LOOP ONand press SRC/OKor
ß/MAIN. To deactivate it, select
LOOP OFFand press SRC/OK
or
ß/MAIN.
603_83_390 Punto C3 GB 19-06-2007 11:21 Pagina 59

6060
}
Or, using voice interaction:
Press
‘and pronounce “Loop
on” or “Loop off”.
Note
With Loop option on, previous and next
track playback will pass to the previous or
next audio track, that will start to be re-
peated.EXIT THE SETTINGS MENU
At the end of any of the operations de-
scribed above, you can exit the settings
menu as described below.
?
To exit the SETTINGSmenu us-
ing manual interaction:
Select EXITand then press
SRC/OKor
ß/MAIN.
}
Or, using voice interaction:
Press
‘and pronounce “Exit”.
Blue&Me™ Nav
SUPPORTED
MOBILE PHONES
Blue&Me™ Navsupports your person-
al devices via the Bluetooth®wireless
technology and USB.
MOBILE PHONES WITH
Bluetooth
®WIRELESS
TECHNOLOGY
Blue&Me™ Navsupports most of the
mobile phones supporting Bluetooth
®1.1
and HandsFree 1.0 profile (refer to Blue-
tooth
®wireless connection specifications
given on your mobile phone owner’s man-
ual).
603_83_390 Punto C3 GB 19-06-2007 11:21 Pagina 60