2007 FIAT DOBLO Cargo boot

80GETTING TO KNOW YOUR VEHICLE
Tipping the entire seat
The seat back and cushion release
devices are in the points shown in fig.
119.
Lift knobs A-fig. 119 and tip the seat
back forwards.
To tip the entire seat, lift the cush-
ion with lever B-fig. 120.
A
fig. 119
F0A0181b
B
fig. 120
F0A0182b
From the inside
With the doors closed, press (to
lock) or lift (to unlock) one of the side
door knobs (Fiat Doblò Passengers
Transport versions). Alternatively, ei-
ther press “LOCK” (to lock) or pull
(to unlock) the front and side door
handles (Fiat Doblò Cargo versions).
The side door knobs will lock or un-
lock only the specific door.
IMPORTANTIf one of the doors
is not shut properly or there is a fail-
ure in the system, the central locking
(where provided) feature will cut out
and after some attempts the device
stops working for about two minutes.
In these two minutes, the doors can
be locked or unlocked manually with-
out the electrical system coming into
play. After the two minutes, the con-
trol unit is ready to receive commands
once more.
If the cause of the failure is removed,
the device will start working proper-
ly, otherwise it will cut out once more.BOOT
EXTENDING THE BOOT
Split seat
Before setting off, make sure that the
seats in the direction of travel and per-
fectly fastened to the anchoring. On-
ly in this position can be seat belts be
used correctly.
The boot can be extended com-
pletely or partially.

84GETTING TO KNOW YOUR VEHICLE
fig. 131
F0A0420b
fig. 130
F0A0412b
– tilt the central seat back pulling
band A-fig. 129upwards;
– pull the bands B-fig. 130and tilt
the seat completely;
– secure tilted seats by the proper
belts C-fig. 131(one per seat) to the
front headrests.
IMPORTANTDo not travel with
second row seats tipped and third row
seats set in normal position of use, a
buzzer will sound to indicate the
wrong seat position.ANCHORING THE LOAD
A boot mat is provided (optional for
Fiat Doblò Cargo base versions). To
fasten the load, fastening hooks are
provided (quantity varying according
to versions) fig. 132secured to the
floor and that can be accessed direct-
ly also if the mat is fitted.
fig. 132
F0A0195b
To re-position the seats, release the
belts C-fig. 131, tilt the side seats and
the central seat cushion then pull band
A-fig. 129to tilt the seat back and an-
chor it to the proper brackets.
It is absolutely forbidden
to travel with the second
row seats tipped and pas-
sengers seated on the third row
seats (as specified on the seat la-
bel).

186TECHNICAL SPECIFICATIONS
PERFORMANCE
Top admitted speed after running-in,
in km/h:
1.4 .................................................... 148
1.4 high roof................................ 145
1.4 7 plae ...................................... 145
1.3 Multijet 75 HP.................. 146
1.3 Multijet 85 HP.................. 153
1.3 Multijet 85 HP
high roof...................................... 150
1.3 Multijet 85 HP 7 place.... 150
1.9 Multijet 100/105 HP........ 168
1.9 Multijet 120 HP................ 175
1.9 Multijet 120 HP
high roof .................................... 172
1.9 Multijet 120 HP 7 place.. 172
DIMENSIONS
fig. 6
F0A0721b
Dimensions are expressed in mm.
Height is intended on an unladen ve-
hicle
Unladen boot volume (Fiat Doblò
Cargo versions): 3,2 m
3.Unladen boot volume (Fiat Doblò
Passengers Transport versions):
– standard conditions 750 dm
3;
– with rear table seat tilted 3000 dm
3.