2007 DODGE SPRINTER center console

167 Controls in detail
Features
3
Cup holders in the frontExample on the right-hand side1Cup holder in the storage compartment
in the dashboardExample on the right-hand side2Bottle holder in the front door3Cup holder compartment in the center
console
4Recess
5Cup holder
6Clamping arm
\1Pull out cup holder compartment3 by
recess4.
Cup holder5 opens fully.
Cup holdersWarning
G
Keep the closeable cup holders closed while
the vehicle is in motion and do not leave
drinks in the cup holders. You or others
could otherwise be injured by objects in the
cup holder being thrown around in the event
of:
\4sharp braking
\4a sudden change of direction
\4an accident
Only place sealable drinking containers of
the correct size in the cup holders. The
drinks could otherwise overspill.
Avoid hot drinks. You could otherwise scald
yourself.!
CAUTION
Do not use the recesses of the cup
holders as an ashtray. You could other-
wise damage the cup holders.
iVehicles with the non-smoking pack-
age are equipped with an additional
cup holder in place of the ashtray.iYou can change the diameter of the cup
holder.

168 Controls in detailFeatures
3
\1Place the container in cup holder5.
\1Press clamping arm6 onto the con-
tainer.
Cup holders in the rear
The cup holders in the rear are located un-
der the seats.
1Cup holder
\1Pull out cup holder1.The ashtray is located in the ashtray com-
partment in the center console.
1Ashtray compartment
2Recess
3Cover\1Pull out ashtray compartment1 by
recess2.
\1To open: fold cover3 upwards.
\1To remove the insert: reach into the
left and right-hand sides of the recess-
es on the ashtray and pull the insert out
to empty it.
\1To replace the insert: hold the insert
and press it down into the retainer.Warning
G
Slide the cup holders back underneath the
seat before leaving the vehicle. You could
otherwise be injured by the protruding cup
holders.
AshtrayWarning
G
Switch off the engine and apply the hand-
brake before removing the ashtray to empty
it.
Otherwise, you could accidentally put the
vehicle in gear.

169 Controls in detail
Features
3
Ashtray in the passenger compart-
ment*
The ashtrays are located on the right-hand
and left-hand side in the side trims.
1Retaining clip
\1To open: open the ashtray.
\1To remove the insert: press clip1
down and remove the entire ashtray
from the trim.
\1To replace the insert: insert the ash-
tray at the bottom into the trim and fold
it closed.The cigarette lighter is located next to the
ashtray in the ashtray compartment in the
center console.
1Cigarette lighter\1Switch on the ignition (\2page 67).
\1Press in cigarette lighter 1.
The cigarette lighter will pop out automati-
cally when the heating element is red-hot.
Cigarette lighter
Warning
G
Only hold the hot cigarette lighter by its
knob. Otherwise, you may burn yourself.
Remove the cigarette lighter if children are
traveling with you. They could injure them-
selves on a hot cigarette lighter or start a
fire.Warning
G
Do not press the cigarette lighter in with too
much force. The ashtray compartment could
otherwise close and trap your finger.

170 Controls in detailFeatures
3
The paper holder is on the control panel for
the air-conditioning system. 1Paper holder
\1Press top of paper holder1.The 12 V sockets for accessories are
\4on the bottom of the center console
(12 V, 25 A)
\4on the inside of the driver's seat base
(12 V, 15 A)
\4in the corner trim next to each rear
door in the passenger compartment
(12 V, 15 A)
\4in the load compartment next to the
rear door on the left-hand side (12 V,
15 A)*.
Socket at the bottom of the center console112 V, 25 A socketYou can use the 12 V sockets (15 A) for ac-
cessories with a maximum power con-
sumption of 180 watts. You can connect
accessories with a maximum power con-
sumption of 300 watts to the 12 V socket
(25 A) at the bottom of the center console.
For more information about the electric air
pump* and the Premium tire sealant*,
please refer to the "Practical hints" section
(\2page 303).
Paper holder
N68.00-2425-31
12 V socket
!
CAUTION
Only connect the electric air pump*
(Premium tire sealant*) to the 12 V
socket (25 A) on the bottom of the cen-
ter console. You could otherwise dam-
age the vehicle electrical system.
iThe sockets are supplied with power
even if the key is removed from the ig-
nition lock. Please note that the battery
may be discharged if you have connect-
ed an accessory, e.g. a coolbox, and
the engine is switched off.

326 Practical hintsFlat tire
5
You can use the Premium tire sealant to
seal small punctures, particularly those in
the tire tread. Tire sealants can be used at
outside temperatures down to –22 °F
(–30 °C).
Prepare the vehicle as described
(\2page 320).\1Try to park the vehicle in such a way
that the tire puncture is close to the
ground. If the tire puncture cannot be
seen, park the vehicle in such a way
that the tire valve of the flat tire is in
horizontal alignment with the axle.
\1It is beneficial to the sealing process if
you remove the foreign body that has
pierced the tire, for example the screw
or nail.
\1Remove the Premium tire sealant, the
accompanying "max. 50 mph
(80 km/h)" sticker and the electric air
pump from the storage compartment in
the right-hand doorway (\2page 303).
\1Affix the sticker within the driver’s field
of vision.Using Premium tire sealant*Warning
G
Smoking, fire and naked flames are prohibit-
ed when handling Premium tire sealant.
Avoid creating sparks.
Warning
G
Your safety is at particular risk and the tire
sealant is unable to repair a tire in the fol-
lowing situations:
\4if there are cuts or punctures in the tire
greater than 0.23 in (6 mm)
\4if the rim is damaged
\4if you have driven with very low tire pres-
sures or with flat tires
Do not drive any further. Consult an autho-
rized Sprinter Dealer which has the neces-
sary specialist knowledge and tools to carry
out the work required.
The manufacturer recommends that you use
an authorized Sprinter Dealer for this pur-
pose. In particular, work relevant to safety
or on safety-related systems must be car-
ried out at an authorized Sprinter Dealer.
!
CAUTION
Only connect the electric air pump to
the 12 V socket (\2page 170) on the
center console (12 V, 25 A, 300 watts).
You could otherwise damage the vehi-
cle electrical system.

328 Practical hintsFlat tire
5
Tire sealant bottle for twin tires7Valve
8Tire sealant bottle with hook, hose and
angle brackets
\1Shake tire sealant bottle8.
\1Unscrew and remove the cap from
valve 7 on tire sealant bottle 8.
\1Press angle bracket 2 (\2page 327)
on hose 3 of the electric air pump all
the way onto valve 7 of tire sealant
bottle 8 and clamp it in place.The following steps may vary depending on
vehicle tires.
\4Single tires (\2page 328).
\4Twin tires, inner wheel (\2page 329)
\4Twin tires, outer wheel (\2page 331)
Single tire
9Hook
aKnob
bLever
cValve core extractor
dTire valve\1Pull knoba out of valve core extractor
c as far as the stop.
\1Unscrew and remove the valve cap
from tire valved on the flat tire.
\1Hook the tire sealant bottle into the up-
per vent hole in the wheel using
hook9.
\1Keep lever b pressed, connect valve
core extractorc firmly to tire valved
and release leverb.
\1Press knob a into the valve core of
tire valved, turning it gently as you do
so, until the shaft of valve core
extractorc engages.
\1Turn knoba counterclockwise until
the valve core is unscrewed.
\1Pull knoba out of valve core extractor
c as far as the stop.
\1This pulls the valve core into the valve
core extractor and seals it against the
valve core extractor stop.
\1Make sure that the pressure release
screw on pressure gauge 5 is closed.
\1Connect connector6 to the 12 V
socket (12 V, 25 A, 300 watts) on the
center console (\2page 170).

330 Practical hintsFlat tire
5
aValve core extractor
bHook
cKnob
dAngle bracket
eTire valve
\1Pull knob c out of valve core
extractora as far as the stop.
\1Screw valve core extractora clock-
wise onto tire valvee.
\1Press knob c into the valve core of
tire valvee, turning it gently as you do
so, until the shaft of valve core
extractora engages.
\1Turn knob c counterclockwise until
the valve core is unscrewed.\1Pull knob c out of valve core
extractora as far as the stop.
This pulls the valve core into the valve
core extractor and seals it against the
valve core extractor stop.
\1Hook tire sealant bottle 8 into the up-
per vent hole in the wheel using hook
b.
\1Press angle bracket d on hose of tire
sealant bottle 8 to the stop on the
flange of valve extractora and clamp
it in place.
\1Make sure that the pressure release
screw on pressure gauge 5 is closed.
\1Connect connector6 to the 12 V
socket (12 V, 25 A, 300 watts) on the
center console (\2page 170).
\1Start the engine (\2page 111).\1Press I on electric air pump switch1.
The electric air pump is switched on.
The tire sealant is then pumped into
the tire and the tire pressure is in-
creased. Allow the electric air pump to
run for at least 10 minutes until tire
sealant bottle 8 is completely empty
and a minimum tire pressure of
43.5 psi (3.0 bar) is achieved.
\1Inflate the tire using the electric air
pump until the recommended tire pres-
sure (\2page 210) is achieved.
\1Then press0 on electric air pump
switch1.
The electric air pump is switched off.
\1Slide knob c quickly to the stop in
valve core extractora.
!
CAUTION
Do not connect the electric air pump
connector to the cigarette lighter sock-
et or another 12 V socket. These are
not designed for operating the electric
air pump.
!
CAUTION
Do not run the electric air pump for
more than 20 minutes without a break,
otherwise it may overheat.
The air pump can be used again once it
has cooled down.

332 Practical hintsFlat tire
5
bTire valve
cAngle bracket
cAngle bracket
dHook\1Hook tire sealant valve 8 into the up-
per vent hole in the wheel using hook
d.
\1Press angle bracket c on hose of tire
sealant bottle 8 (\2page 327) to the
stop on tire valveb and clamp it into
place.
\1Make sure that the pressure release
screw on pressure gauge 5 is closed.
\1Connect connector6 to the 12 V
socket (12 V, 25 A, 300 watts) on the
center console (\2page 170).
\1Start the engine (\2page 111).
\1Press I on electric air pump switch1.
The electric air pump is switched on.
The tire sealant is then pumped into
the tire and the tire pressure is in-
creased.Allow the electric air pump to run until
tire sealant bottle 8 is completely
empty.
\1Press 0 on electric air pump switch1
after about 15 seconds.
\1Unscrew angle bracket c from tire
valveb and remove it.
\1Screw in the valve core with the valve
tool again and take out the valve tool
through the opening.
\1Press angle bracket 2 (\2page 327)
on hose 3 of the electric air pump to
the stop on tire valveb and clamp it
into place.
\1Press switch 1 on the electric air
pump to I and pump up the tire until the
recommended tire pressure
(\2page 210) is achieved.
!
CAUTION
Do not connect the electric air pump
connector to the cigarette lighter sock-
et or another 12 V socket. These are
not designed for operating the electric
air pump.
!
CAUTION
Do not run the electric air pump for
more than 20 minutes without a break,
otherwise it may overheat.
The air pump can be used again once it
has cooled down.