2007 CHRYSLER ASPEN display

3. Simultaneously press and hold both the HomeLink
button that you want to train and the hand-held trans-
mitter button.Do not release the buttons until step 4 has
been completed.The EVIC will display “CHANNEL X
TRAINING”, once the transmitter is programmed the
EVIC will display “CHANNEL X TRAINED”. X refers to
the desired channel being trained (1,2 or 3).
NOTE:Some gate operators and garage door openers
may require you to replace this Programming Step 3 with
procedures noted in theGate Operator/Canadian Pro-
grammingsection.
4. Once “CHANNEL X TRAINED” is displayed on the
EVIC, release both buttons. Programming is now com-
plete. When the HomeLink button is subsequently
pressed, “CHANNEL X TRANSMIT” is displayed on the
screen and your device should be activated, (garage door
should open).NOTE:To program the remaining two HomeLink but-
tons, begin withProgrammingstep two. Do not repeat
step one.
NOTE:If the EVIC display shows “CHANNEL X TR-
ASMIT” (where X is channel 1,2 or 3) but your device
does not activate, the device may be equipped with a
“rolling code” system. Continue with the following steps
five through seven to complete the programming of a
rolling code equipped device (most commonly a garage
door opener manufactured after 1995). The assistance of
a second person may make the following programming
steps quicker and easier.
5.Programming a Rolling Code System
At the garage door opener receiver (motor-head unit) in
the garage, locate thelearnorsmartbutton. This can
usually be found where the hanging antenna wire is
attached to the motor-head unit.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 163
3

6. Firmly press and release thelearnorsmartbutton.
(The name and color of the button may vary by manu-
facturer.)
NOTE:There are 30 seconds in which to initiate step
eight.
7. Return to the vehicle and firmlypress, hold for two
seconds and releasethe programmed HomeLink button.
Repeat thepress/hold/releasesequence a second time,
and, depending on the brand of the garage door opener
(or other rolling code equipped device), repeat this
sequence a third time to complete the programming.
HomeLink should now activate your rolling code
equipped device.
NOTE:To program the remaining two HomeLink but-
tons, begin withProgrammingstep two. Do not repeat
step one. For questions or comments, please contact
HomeLink atwww.homelink.com or 1-800-355-3515.Canadian Programming/Gate Programming
Canadian radio-frequency laws require transmitter sig-
nals totime-out(or quit) after several seconds of
transmission which may not be long enough for
HomeLink to pick up the signal during programming.
Similar to this Canadian law, some U.S. gate operators are
designed totime-outin the same manner.
If you live in Canada or you are having difficulties
programming a gate operator by using theProgram-
mingprocedures (regardless of where you live),replace
Programming HomeLinkstep 3with the following:
3. Continue to press and hold the HomeLink button
while youpress and release every two seconds(cycle)
your hand-held transmitter until the frequency signal has
successfully been accepted by HomeLink. (The EVIC will
display “CHANNEL X TRAINING” and then “CHAN-
NEL X TRAINED”.) Proceed withProgrammingstep
four to complete.
164 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

NOTE:If programming a garage door opener or gate
operator, it is advised to unplug the device during the
cyclingprocess to prevent possible overheating.
Using HomeLink
To operate, simply press and release the programmed
HomeLink button. Activation will now occur for the
trained device (i.e. garage door opener, gate operator,
security system, entry door lock, home/office lighting,
etc.). For convenience, the hand-held transmitter of the
device may also be used at any time. In the event that
there are still programming difficulties or questions, con-
tact HomeLink at:www.homelink.com or 1-800-355-3515
.
Erasing HomeLink Buttons
To erase programming from the three buttons (individual
buttons cannot be erased but can bereprogrammed-
note below), follow the step noted:
•Press and hold the two outer HomeLink buttons, and
the EVIC will display “CLEARING CHANNELS”, donot release the buttons until “CHANNELS
CLEARED” is displayed on the EVIC (after approxi-
mately 20 seconds). Release both buttons. Do not hold
for longer that 30 seconds. HomeLink is now in the
train (or learning) mode and can be programmed at
any time beginning withProgramming- step 2.
Reprogramming a Single HomeLink Button
To program a device to HomeLink using a HomeLink
button previously trained, follow these steps:
1. Press and hold the desired HomeLink button.DO
NOTrelease the button.
2. The EVIC will display “CHANNEL X TRANSMIT” for
20 seconds and then change to “CHANNEL X TRAIN-
ING”. Without releasing the HomeLink button, proceed
withProgrammingstep 2
For questions or comments, contact HomeLink at:
www.homelink.com or 1-800-355-3515.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 165
3

Security
Garage Door Opener Operation with Security
Alarm (if equipped)
If your vehicle is equipped with the Security Alarm
feature, the operation of the HomeLink feature will be
purposely inhibited if the Security Alarm isArmed.
This prevents HomeLink operation due to un-authorized
vehicle entry. HomeLink operation will be re-stored
when the Security Alarm has beenDisarmed(pressing
the unlock button on the remote keyless entry key fob).
If you sell your vehicle, be sure to erase the HomeLink
buttons, by following the “Erasing HomeLink Buttons”
instructions in this section..
To erase all previously trained frequencies, press and
hold the two outer HomeLink buttons, and the EVIC will
display “CLEARING CHANNELS”, do not release the
buttons until “CHANNELS CLEARED” is displayed on
the EVIC (after approximately 20 seconds). Release both
buttons. Do not hold for longer that 30 seconds.This device complies with part 15 of FCC rules and with
RSS-210 of Industry Canada. Operation is subject to the
following conditions:•This device may not cause harmful interference.
•This device must accept any interference that may be
received including interference that may cause undes-
ired operation.
NOTE:Changes or modifications not expressly ap-
proved by the party responsible for compliance could
void the user’s authority to operate the equipment.
In the event that you are still having programming
difficulties, questions, or comments, call toll free 1–800–
355–3515, or on the internet at www.homelink.com for
information or assistance.
HomeLinkis a trademark owned by Johnson Controls,
Inc.
166 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

▫Operating Instructions - Hands Free Phone —
If Equipped.........................207
▫Operating Instructions - Satellite Radio —
If Equipped.........................207
Sales Code RAQ – AM/FM/CD (6-Disc) Radio
With Optional Satellite Radio, Hands Free Phone,
And Vehicle Entertainment Systems (VES)
Capabilities...........................208
▫Operating Instructions - Radio Mode.......208
▫Operation Instructions - (CD Mode For CD
Audio Play).........................213
▫Load/Eject Button (CD Mode For CD
Audio Play).........................215
▫Notes On Playing MP3 Files.............217
▫Operation Instructions - (CD Mode For MP3
Audio Play).........................219▫Load/Eject Button (CD Mode For MP3 Play) . . 219
Sales Code REC — AM/FM/CD (6–Disc) Radio
With Navigation System..................222
▫Operating Instructions — Satellite Radio
(If Equipped)........................222
▫REC Setting The Clock.................222
▫Audio Clock Display...................225
Video Entertainment System (Sales Code XRV) —
If Equipped...........................226
Satellite Radio — If Equipped..............226
▫System Activation.....................226
▫Electronic Serial Number/Sirius Identification
Number (ESN/SID)....................227
▫Selecting Satellite Mode In REF, RAQ, And RAK
Radios.............................228
182 INSTRUMENT PANEL AND CONTROLS

15. Gear Selector
The electronic gear selector display is self-contained
within the instrument cluster. It displays the position of
the automatic transmission shift lever, and the relation of
each position to all other positions. For a good signal the
display will place a box around the selected transmission
range (PRND21). If the PRNDL displays only the char-
acters PRND21 (no boxes) have the system checked by an
authorized dealer.
16. Trip Odometer
The trip odometer shows individual trip mileage. To
toggle between the odometer and the trip odometer,
press the Odometer/Trip Odometer Button. To reset the
Trip Odometer, press and hold the button while in trip
mode, until the Trip Odometer resets.
Also the cluster will display, replacing the odometer,
vehicle warning messages such as: door ajar, gate ajar,
low wash, No-fuse, and the outside temperature.The outside temperature will display in the odometer for
non-Electronic Vehicle Information Center (EVIC)
equipped vehicles. Pressing the trip odometer reset but-
ton toggles the feature back to the odometer.
NOTE:If vehicle is equipped with the optional Elec-
tronic Vehicle Information Center (EVIC), all warnings
including door ajar, liftgate open, low washer fluid, will
only be displayed in the EVIC display. For additional
information, refer to “Electronic Vehicle Information Cen-
ter — If Equipped” in Section 3.
17. Odometer
The odometer shows the total distance the vehicle has
been driven.
U.S. federal regulations require that upon transfer of
vehicle ownership, the seller certify to the purchaser the
correct mileage that the vehicle has been driven. There-
fore, if the odometer reading is changed during repair or
INSTRUMENT PANEL AND CONTROLS 191
4

29. TOW/HAUL
The TOW/HAUL button is located at the end of the gear
shift lever. This light will illuminate when the TOW/
HAUL button has been selected.
30. 4LOW Indicator
Indicates transfer case is in 4LOW position.
31. Odometer/Trip Odometer Button
Press this button to toggle between the odometer and the
trip odometer display. Holding the button in resets the
trip odometer reading.
ELECTRONIC DIGITAL CLOCK
The clock and radio each use the display panel built into
the radio. A digital readout shows the frequency and/or
time in hours and minutes (depending on your radio
model) whenever the ignition switch is in the “ON” or
“ACC” position.When the ignition switch is in the “OFF” position, or
when the radio frequency is being displayed, time keep-
ing is accurately maintained.
On the AM/FM/CD (6-disc) radio the time button alter-
nates the location of the time and frequency on the
display. On the AM/FM/CD (single-disc) radio only one
of the two, time or frequency is displayed.
Clock Setting Procedure
1. Press and hold the time button until the hours blink.
2. Adjust the hours by turning the right side Tune /
Audio control.
3. After the hours are adjusted, press the right side Tune
/ Audio control to set the minutes.
4. Adjust the minutes using the right side Tune / Audio
control.
INSTRUMENT PANEL AND CONTROLS 197
4

Mode Button (Radio Mode)
Press the mode button repeatedly to select between the
CD player and Satellite Radio (if equipped).
SEEK Button (Radio Mode)
Press and release the SEEK button to search for the next
listenable station in either AM/FM or Satellite (if
equipped) mode. Press the right side of the button to seek
up and the left side to seek down. The radio will remain
tuned to the new station until you make another selec-
tion. Holding the button will bypass stations without
stopping until you release it.
MUTE Button (Radio Mode)
Press the MUTE button to cancel the sound from the
speakers.MUTEwill display. Press the MUTE button a
second time and the sound from the speakers will return.
Rotating the volume control, turning the radio ON/OFF,
or turning ON/OFF the ignition, will cancel the MUTE
feature.NOTE:In Hands Free Phone (if equipped) mode, the
MUTE button mutes the microphone.
SCAN Button (Radio Mode)
Pressing the SCAN button causes the tuner to search for
the next listenable station in either, AM, FM, or Satellite
(if equipped) frequencies, pausing for 5 seconds at each
listenable station before continuing to the next. To stop
the search, press SCAN a second time.
PSCAN Button (Radio Mode)
Pressing the PSCAN button causes the tuner to scan
through preset stations in either, AM, FM, or Satellite (if
equipped) frequencies, pausing for 5 seconds at each
preset station before continuing to the next. To stop the
search, press PSCAN a second time.
Time Button
Press the time button and the time of day will display for
5 seconds.
INSTRUMENT PANEL AND CONTROLS 201
4