2007 CHEVROLET OPTRA 5 lock

{CAUTION:
If you spill fuel and then something
ignites it, you could be badly burned.
Fuel can spray out on you if you open
the fuel cap too quickly. This spray can
happen if your tank is nearly full, and is
more likely in hot weather. Open the fuel
cap slowly and wait for any hiss noise to
stop. Then unscrew the cap all the way.
Be careful not to spill fuel. Do not top off or overfill
the tank and wait a few seconds after you have
finished pumping before removing the nozzle.
Clean fuel from painted surfaces as soon as
possible. SeeWashing Your Vehicle on page 339.
When replacing the fuel cap, turn it to the right
(clockwise) until it clicks. Make sure the cap is fully
installed. The diagnostic system can determine
if the fuel cap has been left off or improperly
installed. This would allow fuel to evaporate into
the atmosphere. SeeMalfunction Indicator
Lamp on page 172.
{CAUTION:
If a re starts while you are refueling, do
not remove the nozzle. Shut off the ow
of fuel by shutting off the pump or by
notifying the station attendant. Leave the
area immediately.
Notice:If you need a new fuel cap, be sure to
get the right type. Your dealer can get one
for you. If you get the wrong type, it may not
t properly. This may cause your malfunction
indicator lamp to light and may damage
your fuel tank and emissions system. See
Malfunction Indicator Lamp on page 172.
255

A. Engine Air Cleaner/Filter. SeeEngine Air
Cleaner/Filter on page 264.
B. Engine Oil Fill Cap. See “When to Add Engine
Oil” underEngine Oil on page 260.
C. Engine Oil Dipstick. See “Checking Engine Oil”
underEngine Oil on page 260.
D. Brake Fluid/Hydraulic Clutch Fluid Reservoir.
See “Brake Fluid” underBrakes on page 281
andHydraulic Clutch on page 266.
E. Power Steering Fluid Reservoir. SeePower
Steering Fluid on page 279.F. Engine Coolant Surge Tank. SeeCooling
System on page 273.
G. Engine Compartment Fuse Block. SeeEngine
Compartment Fuse Block on page 349.
H. Windshield Washer Fluid Reservoir. See
“Adding Washer Fluid” underWindshield
Washer Fluid on page 280.
I. Battery. SeeBattery on page 284.
259

1. You can remove the coolant surge tank
pressure cap when the cooling system,
including the coolant surge tank pressure cap
and upper radiator hose, is no longer hot.
Turn the pressure cap slowly counterclockwise
about two or two and one-half turns.
If you hear a hiss, wait for that to stop.
This will allow any pressure still left to be
vented out the discharge hose.
2. Then keep turning the pressure cap slowly,
and remove it.
277

3. Disconnect the wiring harness connector from
the rear of the bulb.
4. Remove the headlamp cap (A for the
low-beam or B for the high-beam headlamp)
by turning it counterclockwise.
5. Release the spring that retains the bulb.
6. Remove the old bulb.
7. Install a new bulb.
8. Reverse Steps 1 through 5 to install the
headlamp assembly.
Wagon Models
Hatchback Models
291

Front Turn Signal and Parking Lamps
To replace a front turn signal or parking lamp
bulb, do the following:
1. Open the hood. SeeHood Release on
page 257for more information.
2. Remove the two bolts from the top of the
headlamp assembly and one nut on the
inside that retains the headlamp assembly.
3. Turn the bulb socket counterclockwise.
4. Pull the bulb socket out of the lamp housing.
5. Press the bulb inward and turn it
counterclockwise to remove it from the
bulb socket.
6. Install the new bulb into the bulb socket by
pressing it in and turning it clockwise.
7. Reinstall the bulb socket into the lamp
housing by turning it clockwise.
8. Reverse Steps 1 through 2 to install the
assembly.
Wagon Models
Hatchback Models
292

Turn Signal Lamps (Side)
Your vehicle may have this side turn signal lamp.
It will be located between the front door and
the wheel well. To replace this bulb, do the
following:
1. Locate the bulb by reaching underneath the
vehicle where the side turn signal lamp is
located.
2. Remove the side turn signal lamp assembly
by pulling it forward.
3. Turn the bulb socket counterclockwise.
4. Remove the bulb from the lamp housing by
pulling the bulb straight out of the socket.
5. Install the new bulb into the bulb socket by
pushing it in and turning it clockwise.
6. Push the side turn signal lamp assembly back
into its original position.
293

Sidemarker Lamps (Front)
To replace a front sidemarker bulb, do the
following:
1. Open the hood. SeeHood Release on
page 257for more information.
2. Remove the headlamp assembly.
3. Turn the front sidemarker bulb socket
counterclockwise.
4. Pull the front sidemarker bulb socket out of
the front bumper.
5. Pull the old bulb straight out of the bulb
socket.
6. Push the new bulb straight into the socket.
7. Reverse Steps 1 through 5 to install the
assembly.
294

Sidemarker Lamps (Rear)
To replace a rear sidemarker bulb, do the
following:
1. Reach inside of the rear bumper and locate
the socket.
2. Turn the rear sidemarker bulb socket
counterclockwise.3. Pull the rear sidemarker bulb socket out of
the rear bumper.
4. Pull the old bulb straight out from the bulb
socket.
5. Push the new bulb straight into the socket.
6. Reverse Steps 1 through 3 to install the
bulb socket.
295