2007 CHEVROLET OPTRA 5 lock

Taillamps, Turn Signal, and
Stoplamps (Hatchback)
To replace one of these bulbs, do the following:
1. Open the liftgate. SeeLiftgate on page 99for
more information.
2. Remove the two screws and the taillamp
assembly.
3. Remove the bulb socket by turning it
counterclockwise from the taillamp assembly.4. Remove the bulb from the socket by pressing
the bulb and turning it counterclockwise.
5. Install the appropriate new bulb into the
socket.
6. Reverse Steps 1 through 3 to install the lamp
assembly.
298

Taillamps, Turn Signal, Stoplamps
and Back-up Lamps (Wagon)
To replace one of these bulbs, do the following:
1. Open the liftgate. SeeLiftgate on page 99
for more information.
2. Remove the two screws from the taillamp
assembly.3. Remove the taillamp assembly from the
vehicle.
4. Remove the bulb socket by turning it
counterclockwise from the taillamp assembly.
5. Remove the bulb from the socket by pressing
the bulb and turning it counterclockwise.
6. Install the appropriate new bulb into the
socket.
7. Reverse Steps 1 through 4 to install the lamp
assembly.
299

Taillamps, Stoplamps and Back-up
Lamps (Hatchback)
To replace one of these bulbs, do the following:
1. Open the liftgate. SeeLiftgate on page 99for
more information.
2. Remove the protective cover.
3. Remove the bulb socket by turning it
counterclockwise.4. Remove the bulb from the socket by pressing
the bulb and turning it counterclockwise.
5. Install the appropriate new bulb into the
socket.
6. Reinstall the protective cover.
300

License Plate Lamp
To replace one of these bulbs, do the following:
1. Remove the two screws holding each of the
license plate lamps.
2. Turn and pull the license plate lamp toward
you through the opening.3. Turn the bulb socket counterclockwise and
pull the bulb straight out of the socket.
4. Install the new bulb.
5. Reverse Steps 1 through 3 to reinstall the
license plate lamp.
Replacement Bulbs
Exterior Lamps Bulb Number
Back-up 94535571
CHMSL, Front and
Rear Sidemarker94535587
License Plate Lamp 94535587
Headlamps
High-Beam 94535541
Low-Beam 94535546
Stoplamp and Taillamp 94535574
Turn Signal - Front and
Parking Lamp94535578
Turn Signal - Rear 94535572
For replacement bulbs not listed here, contact
your dealer.
301

Different Size Tires and Wheels
If you add wheels or tires that are a different size
than your original equipment wheels and tires,
this may affect the way your vehicle performs,
including its braking, ride and handling
characteristics, stability, and resistance to rollover.
Additionally, if your vehicle has electronic
systems such as, anti-lock brakes, traction control,
and electronic stability control, the performance
of these systems can be affected.{CAUTION:
If you add different sized wheels, your
vehicle may not provide an acceptable
level of performance and safety if tires
not recommended for those wheels are
selected. You may increase the chance
that you will crash and suffer serious
injury. Only use GM specic wheel and
tire systems developed for your vehicle,
and have them properly installed by a
GM certied technician.
SeeBuying New Tires on page 318and
Accessories and Modifications on page 249for
additional information.
319

{CAUTION:
Changing a tire can be dangerous. The
vehicle can slip off the jack and roll over or
fall on you or other people. You and they
could be badly injured or even killed. Find a
level place to change your tire. To help
prevent the vehicle from moving:
1. Set the parking brake rmly.
2. Put an automatic transaxle shift lever
in PARK (P), or shift a manual
transaxle to FIRST (1) or REVERSE (R).
3. Turn off the engine and do not restart
while the vehicle is raised.
4. Do not allow passengers to remain in
the vehicle.
To be even more certain the vehicle will not
move, you should put blocks at the front
and rear of the tire farthest away from the
one being changed. That would be the tire
on the other side, at the opposite end of the
vehicle.When you have a flat tire, use the following
example as a guide to assist you in the placement
of wheel blocks.
The following information will tell you how to use
the jack and change a tire.
325

5. Turn the retainer on the compact spare tire
counterclockwise and remove the retainer.
6. Remove the compact spare tire. SeeCompact
Spare Tire on page 334for more information.7. To access the tools, pull the strap on the tool
box cover upward. The tools are located
inside the foam tray.
327

Hatchback Models
For hatchback models, do the following to access
the spare tire and tools:
1. Open the liftgate. SeeLiftgate on page 99for
more information.
2. Remove the trim cover by pulling up on the tab.
3. Remove the foam tray that contains the tools.
4. Turn the retainer on the compact spare tire
counterclockwise and remove the retainer.5. Remove the compact spare tire. SeeCompact
Spare Tire on page 334for more information.
6. Remove the jack by turning the jack retainer,
located on the right side of the jack,
counterclockwise to release it. The jack is
located in the trunk, in front of the compact
spare tire.
7. Then remove the jack handle and the wheel
wrench. The jack handle and the wheel
wrench are located inside the foam tray.
328