2007 CHEVROLET AVEO headlamp

Headlamps (Hatchback)
To replace a headlamp bulb, do the following:
1. Open the hood. SeeHood Release on
page 274for more information.
2. Remove the five screws from top of the
radiator grille.
3. Remove the radiator grille.
4. Remove the three bolts from the
headlamp assembly.5. Remove the headlamp assembly.
6. Disconnect the wiring harness connector from
the rear of the bulb.
7. Remove the headlamp cap.
310

8. Release the spring that retains the bulb by
loosing the screw.
9. Remove the old bulb.
10. Install the new bulb.
11. Install the bulb retaining spring.
12. Reverse Steps 1 through 8 to install the
headlamp assembly.
Headlamps (Sedan)
To replace a headlamp bulb, do the following:
1. Open the hood. SeeHood Release on
page 274for more information.
2. Remove the three bolts from the
headlamp assembly.
3. Remove the headlamp assembly.
4. Disconnect the wiring harness connector from
the rear of the bulb.
5. Remove the headlamp cap.
311

6. Release the spring that retains the bulb.
7. Remove the old bulb.
8. Install the new bulb.
9. Install the bulb retaining spring.
10. Reverse Steps 1 through 6 to install the
headlamp assembly.
Front Turn Signal and Parking
Lamps (Hatchback)
To replace a front turn signal or parking lamp
bulb, do the following:
1. Remove the radiator grille and the headlamp
assembly. See Steps 2 through 5 under
Headlamps (Hatchback) on page 310or
Headlamps (Sedan) on page 311for
instructions on how to remove the
headlamp assembly.
2. Turn the front turn signal bulb socket
counterclockwise.
312

3. Pull the front turn signal bulb socket out of the
lamp housing.
4. Press the bulb inward and turn it
counterclockwise to remove it from the
bulb socket.
5. Install the new bulb into the socket by
pressing it in and turning it clockwise.
6. Install the socket into the lamp housing by
turning it clockwise.
7. Reverse Steps 1 through 4 to install the
assembly.
Front Turn Signal and Parking
Lamps (Sedan)
To replace a front turn signal or parking lamp
bulb, do the following:
1. Open the hood. SeeHood Release on
page 274for more information.
2. Remove the headlamp assembly. See Steps 2
through 4 underHeadlamps (Hatchback) on
page 310orHeadlamps (Sedan) on page 311
for instructions on how to remove the
headlamp assembly.3. Turn the front turn signal bulb socket
counterclockwise.
4. Pull the front turn signal bulb socket out of the
lamp housing.
5. Press the bulb inward and turn it
counterclockwise to remove it from the
bulb socket.
313

6. Install the new bulb into the socket by
pressing it in and turning it clockwise.
7. Install the socket into the lamp housing by
turning it clockwise.
8. Reverse Steps 1 through 2 underHeadlamps
(Hatchback) on page 310orHeadlamps
(Sedan) on page 311to install the assembly.
Turn Signal Lamps (Side)
To replace a side turn signal bulb, do the following:
1. Open the hood. SeeHood Release on
page 274for more information.
2. See Steps 2 through 5 underHeadlamps
(Hatchback) on page 310orHeadlamps
(Sedan) on page 311to access the side turn
signal lamps.
3. Remove the side turn signal lamp assembly
by pulling it forward.
4. Turn the bulb socket counterclockwise.5. Remove the bulb from the lamp housing by
pulling the bulb straight out of the socket.
6. Install the new bulb into the bulb socket by
pushing it in and rotating the bulb socket
clockwise.
7. Push the side turn signal lamp assembly back
into its original position.
314

License Plate Lamp
To replace one of these bulbs, do the following:
1. Remove the two screws holding each of the
license plate lamps.
2. Turn and pull the license plate lamp toward
you through the opening.
3. Turn the bulb socket counterclockwise and
pull the bulb straight out of the socket.
4. Install the new bulb.
5. Reverse Steps 1 through 3 to reinstall the
license plate lamp.
Replacement Bulbs
Exterior Lamp Bulb Number
Back-Up 94535571
Center High-Mounted
Stoplamp (CHMSL)94535587
Headlamps 94535548
Front Parking/Turn
Signal (Hatchback)94535574
Front Parking/Turn
Signal (Sedan)94535574
Side Turn Signal (Hatchback) 94535587
Side Turn Signal (Sedan) 94535587
Stoplamp/Taillamps 94535574
Turn Signal Lamps 94535572
For replacement bulbs not listed here, contact
your dealer/retailer.
317

Each new wheel should have the same
load-carrying capacity, diameter, width, offset and
be mounted the same way as the one it replaces.
If you need to replace any of your wheels, wheel
bolts, or wheel nuts, replace them only with
new GM original equipment parts. This way, you
will be sure to have the right wheel, wheel
bolts, and wheel nuts for your vehicle.
{CAUTION:
Using the wrong replacement wheels,
wheel bolts, or wheel nuts on your vehicle
can be dangerous. It could affect the
braking and handling of your vehicle,
make your tires lose air and make you
lose control. You could have a collision in
which you or others could be injured.
Always use the correct wheel, wheel bolts,
and wheel nuts for replacement.Notice:The wrong wheel can also cause
problems with bearing life, brake cooling,
speedometer or odometer calibration,
headlamp aim, bumper height, vehicle ground
clearance, and tire or tire chain clearance
to the body and chassis.
SeeChanging a Flat Tire on page 336for more
information.
Used Replacement Wheels
{CAUTION:
Putting a used wheel on your vehicle is
dangerous. You cannot know how it has
been used or how far it has been driven. It
could fail suddenly and cause a crash. If
you have to replace a wheel, use a new
GM original equipment wheel.
334

Electrical System
Add-On Electrical Equipment
Notice:Do not add anything electrical to your
vehicle unless you check with your dealer
rst. Some electrical equipment can damage
your vehicle and the damage would not
be covered by your warranty. Some add-on
electrical equipment can keep other
components from working as they should.
Add-on equipment can drain your vehicle’s battery,
even if your vehicle is not operating.
Your vehicle has an airbag system. Before
attempting to add anything electrical to your
vehicle, seeServicing Your Airbag-Equipped
Vehicle on page 82.
Headlamp Wiring
The headlamp wiring is protected by fuses in the
fuse block. An electrical overload will cause
the lamps to turn off. If this happens, have your
headlamp wiring checked right away.
Windshield Wiper Fuses
The windshield wiper motor is protected by an
internal circuit breaker and a fuse. If the motor
overheats due to heavy snow, etc., the wiper will
stop until the motor cools. If the overload is
caused by some electrical problem and not snow,
etc., be sure to get it fixed.
355