2007 CADILLAC DTS buttons

Heated and Cooled Seats
Your vehicle may have heated and cooled front
seats.
To operate the heated or cooled seats, the ignition
must be on.
The buttons are located
on the front doors.
I(Heated Seatback):Press this button to turn
on the heated seatback.
H(Cooled Seat):Press this button to turn on the
cooled seat.
J(Heated Seat and Seatback):Press this
button to turn on the heated seat and seatback.
Press a button to turn on the desired feature.
A light on that button will display to show which
feature is on.
There are three temperature settings for each
feature. A column of three lights next to the buttons
will display which setting the feature is in: high,
medium or low. Three lights indicate the highest
setting, two lights for medium and one light for the
lowest setting.
When you press a button, the feature will turn on at
the highest setting. Each time you press the button,
the feature will go down one temperature setting.
To turn the feature off, keep pressing the button
until the display lights turn off.
If your vehicle has remote vehicle start and is
started using the remote keyless entry transmitter,
the front heated seats will be turned on to the high
setting if it is cold outside. See “Remote Vehicle
Start” underRemote Keyless Entry (RKE) System
Operation on page 96. When the key is inserted
into the ignition and the ignition is turned on, the
heated seat feature will turn off. To turn the heated
seat feature back on, press the desired button.
Driver’s Side Buttons
Shown, Passenger’s
Side Buttons Similar
11

If you use the remote keyless entry transmitter to
enter your vehicle and the remote recall memory
feature is on, automatic seat and mirror movement
will occur. See “MEMORY SEAT RECALL”
underDIC Vehicle Customization on page 259for
more information.
To stop recall movement of the memory feature at
any time, press one of the power seat controls,
memory buttons, power tilt wheel control, or power
mirror buttons.
If something has blocked the driver’s seat and/or
the steering column while recalling a memory
position, the driver’s seat and/or the steering
column recall may stop. If this happens remove
the obstruction, then press the appropriate control
for the area that is not recalling for two seconds.
Try recalling the memory position again by
pressing the appropriate memory button. If the
memory position is still not recalling, see
your dealer for service.Easy Exit Seat
The control for this feature is located on the
driver’s door panel between buttons 1 and 2.
With the vehicle in PARK (P), the exit position can
be recalled by pressing the exit button. You will
hear a single beep. The driver’s seat will move
back, and if the vehicle has the power tilt wheel and
telescopic steering feature, the power telescopic
steering column will move up and forward.
If the easy exit seat feature is on in the DIC,
automatic seat and power telescopic steering
column movement will occur when the key
is removed from the ignition. See “EASY EXIT
SEAT” underDIC Vehicle Customization on
page 259for more information.
Further programming for automatic seat and
steering wheel movement can be done using the
Driver Information Center (DIC). You can select
or not select the following:
The easy exit seat feature
The memory seat recall feature
For programming information, seeDIC Vehicle
Customization on page 259.
13

Center Seat
Your vehicle may have a front center seat. This
seat can be converted to a storage area by
lowering the seatback. SeeCenter Flex Storage
Unit on page 156.
For information on safety belts for this position,
seeCenter Front Passenger Position on page 35.
Rear Seats
Heated Seats
Your vehicle may have heated rear seats.
To operate the rear heated seats, the ignition
must be on.
The buttons are located
on the rear doors.
I(Heated Seatback):Press this button to turn
on the heated seatback.
J(Heated Seat and Seatback):Press this
button to turn on the heated seat and seatback.
17

Press a button to turn on the desired feature. A
light on that button will display to show which
feature is on.
There are three temperature settings for each
feature. A column of three lights next to the
buttons will display which setting the feature is in:
high, medium or low. Three lights indicate the
highest setting, two lights for medium and one light
for the lowest setting.
When you press a button, the feature will turn on
at the highest setting. Each time you press the
button, the feature will go down one temperature
setting.
To turn the feature off, keep pressing the button
until the display lights turn off.
Rear Seat Pass-Through Door
Your vehicle has a pass-through door that provides
access to the trunk from the rear seats. See
“Rear Seat Pass-Through Door” underTrunk on
page 106.
Power Lumbar
Your vehicle may be equipped with four-way
lumbar support, without the massage feature, for
the outboard rear seat positions.
The rear lumbar support
controls are located on
the rear doors in
front of the heated seat
buttons.
To turn on the lumbar support feature, press the
front of the control to increase support or rearward
to decrease support. The lumbar control can
also be moved up and down to adjust the location
of the support.
The ignition does not need to be on for the power
lumbar feature to work.
18

To start the vehicle using the remote start feature,
do the following:
1. Aim the transmitter at the vehicle.
2. Press and release the transmitter’s lock
button, then immediately press and hold
the transmitter’s remote start button until the
turn signal lights ash or if the vehicle’s
lights are not visible, press and hold the
remote start button for at least four seconds.
The vehicle’s doors will lock. Pressing the
remote start button again after the vehicle has
started will turn off the ignition.
When the vehicle starts, the parking lamps will
turn on and remain on while the vehicle is
running.
3. If it is the rst remote start since the vehicle
has been driven, repeat these steps, while
the engine is still running, to extend the engine
running time by 10 minutes. Remote start
can be extended one time.
After entering the vehicle during a remote start,
insert and turn the key to RUN to drive the vehicle.
If the vehicle is left running it will automatically
shut off after 10 minutes unless a time extension
has been done.To manually shut off a remote start, do any of the
following:
Aim the RKE transmitter at the vehicle and
press the remote start button until the parking
lamps turn off.
Turn on the hazard warning ashers.
Turn the ignition switch on and then off.
The remote vehicle start feature provides two
separate starts, each with 10 minutes of engine
running, or it provides one start with 10 minutes of
engine running that may be extended 10 more
minutes. If you press and release the transmitter
lock button and then press and hold the remote
start button on the RKE transmitter again before the
rst 10 minutes of engine running time has expired,
10 minutes are added to the remaining minutes. For
example, if the lock button and then the remote
start buttons are pressed again after ve minutes of
the engine run time, 10 minutes are added and you
now have 15 minutes of engine running. The added
ten minutes are considered a second remote
vehicle start.
Once two remote starts or a single start with a
time extension have been used, the vehicle must
be started with the ignition key before you can
use the remote start feature again.
101

OnStar®service cannot work unless your vehicle
is in a place where OnStar®has an agreement
with a wireless service provider for service in that
area. OnStar
®service also cannot work unless
you are in a place where the wireless service
provider OnStar
®has hired for that area
has coverage, network capacity and reception
when the service is needed, and technology that
is compatible with the OnStar
®service. Not all
services are available everywhere, particularly in
remote or enclosed areas, or at all times.
OnStar
®service that involves location information
about your vehicle cannot work unless GPS
satellite signals are unobstructed and available in
that place as well.Your vehicle must have a working electrical
system (including adequate battery power) for the
OnStar
®equipment to operate. There are other
problems OnStar®cannot control that may prevent
OnStar®from providing OnStar®service to you
at any particular time or place. Some examples are
damage to important parts of your vehicle in an
accident, hills, tall buildings, tunnels, weather
or wireless phone network congestion.
Your Responsibility
You may need to increase the volume of your
radio to hear the OnStar®advisor. If the light next
to the OnStar®buttons is red, this means that
your system is not functioning properly and should
be checked by your dealer/retailer. If the light
appears clear (no light is appearing), your OnStar
®
subscription has expired. You can always press
the OnStar®button to conrm that your OnStar®
equipment is active.
142

Universal Home Remote
System
System Identication
Your vehicle may have a Universal Home Remote
System.
Determine which Universal Home Remote your
vehicle has and then read the pages following for
instructions on programming your specic
system.
If there is one triangular Light Emitting Diode
(LED) indicator light above the Universal Home
Remote buttons, follow the instructions under
Universal Home Remote System Operation (With
One Triangular LED).If there are three round LED indicator lights above
the Universal Home Remote buttons, follow the
instructions under Universal Home Remote System
Operation (With Three Round LED).
For help or information on the Universal Home
Remote System, call the customer assistance
phone number underCustomer Assistance Offices
on page 486.
143

Universal Home Remote System
The Universal Home Remote System provides a
way to replace up to three hand-held
Radio-Frequency (RF) transmitters used to
activate devices such as garage door openers,
security systems, and home lighting.
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following
two conditions:
1. This device may not cause harmful
interference.
2. This device must accept any interference
received, including interference that may
cause undesired operation.
This device complies with RSS-210 of Industry
Canada. Operation is subject to the following two
conditions:
1. This device may not cause interference.
2. This device must accept any interference
received, including interference that may
cause undesired operation of the device.
Changes or modications to this system by other
than an authorized service facility could void
authorization to use this equipment.
Universal Home Remote System
Operation (With One Triangular LED)
If there is one triangular Light Emitting Diode
(LED) indicator light above the Universal Home
Remote buttons, follow the instructions below.
Do not use the Universal Home Remote with any
garage door opener that does not have the stop
and reverse feature. This includes any garage door
opener model manufactured before April 1, 1982. If
you have a newer garage door opener with rolling
codes, please be sure to follow Steps 6 through 8 to
complete the programming of your Universal Home
Remote Transmitter.
144