2007 CADILLAC DTS Owners Manual

{CAUTION:
FCA is only a warning system and does
not apply the brakes. When you are
approaching a vehicle or object too
rapidly or when you are following a
vehicle too closely that is ahead of you,
FCA may not provide you with enough
time to avoid a collision. FCA is not
designed to warn the driver of pedestrians
or animals. Your complete attention is
always required while driving and you
should be ready to take action and apply
the brakes. For more information,
seeDefensive Driving on page 302.The FCA control is
located on the steering
wheel.
To enable or disable FCA, press the Adaptive
Cruise Control button. SeeAdaptive Cruise Control
on page 179.
169

FCA is enabled when the green light on the button
is lit. FCA is disabled when the indicator light is
amber.
{CAUTION:
On winding roads, FCA may not detect
a vehicle ahead. You could crash into
a vehicle ahead of you. Do not rely on
FCA on winding roads.
When weather limits visibility,
such as in fog, rain, or snow, FCA
performance is limited. There may not
be enough warning distance to the
vehicle in front of you. Do not rely
on FCA in low visibility conditions.
{CAUTION:
When FCA is enabled, the Adaptive Cruise
Control switch is on. If you press another
Adaptive Cruise Control button, you might
CAUTION: (Continued)
CAUTION: (Continued)
go into cruise when you do not want to.
You could be startled and even lose
control. Be careful not to press adaptive
cruise buttons unless you want to use
cruise control.
Alerting the Driver
The FCA alert symbol
will ash and a warning
beep will sound when
driver action may be
required.
The alert symbol will ash when:
Your vehicle is approaching another vehicle
too quickly.
Your vehicle is following a vehicle ahead of
you much too closely.
SeeDefensive Driving on page 302for more
information.
170

Detecting the Vehicle Ahead
The vehicle ahead symbol, located next to the
FCA symbol, will only appear when a vehicle
ahead of you is detected in your path. If this
symbol does not appear, or disappears briey,
FCA will not respond to vehicles you may
see ahead. The symbol may disappear on curves,
highway exit ramps, or hills. Also, when another
vehicle enters the same lane as you, the FCA
system will not detect the vehicle until it is
completely in your driving lane.
{CAUTION:
When the Adaptive Cruise Control radar is
blocked by snow, ice, or dirt, it may not
detect a vehicle ahead. FCA may not
help you avoid a collision under these
conditions. Do not use FCA when the
radar is blocked by snow, ice, or dirt.
Keep your radar clean. See “Cleaning
the System” underAdaptive Cruise
Control on page 179.
{CAUTION:
FCA may not detect and warn soon enough
to stationary or slow-moving vehicles or
other objects ahead of you. You could
crash into an object ahead of you. Do not
rely on FCA when approaching stationary
or slow-moving vehicles or other objects.
Unnecessary Alerts
FCA may occasionally provide alerts that you
consider unnecessary. It could respond to a turning
vehicle ahead of you, guard rails, signs, and other
stationary objects. This is normal operation, your
vehicle does not need service.
Other Messages
There are three messages that may appear
on the Driver Information Center (DIC). They are
CLEAN RADAR, RADAR CRUISE NOT READY
and SERVICE RADAR CRUISE. SeeDIC
Warnings and Messages on page 246.
171

Cleaning the System
The radar can become blocked by snow, ice, or
dirt. If so, you may need to turn off the engine
and clean the lens. See “Cleaning the System”
underAdaptive Cruise Control on page 179.
Flash-to-Pass
This feature lets you use the high-beam
headlamps to signal the driver in front of
you that you want to pass.
The ash-to-pass feature will only work with the
headlamps on. It does not work with Daytime
Running Lamps (DRL).
Pull and hold the turn signal lever toward you
to use.
If the headlamps are on high beam, they will
switch to low beam. To return to high beam,
push the lever away from you.
Windshield Wipers
You control the windshield wipers by turning the
band with the wiper symbol on it.
8(Mist):Turn the band to mist for a single
wiping cycle. Hold it there until the wipers start.
Then let go. The wipers stop after one wipe.
For more wipe cycles, hold the band longer
on mist.
6(Delay):Turn the band to choose the delay time
between wipe cycles. The wiper speed can be set
for a long or short delay between wipes. The closer
the band is set to the top of the lever, the shorter
the delay.
6(Low Speed):Turn the band away from
you to the rst solid band past the delay settings
for steady wiping at low speed.
1(High Speed):For high-speed wiping, turn
the band further, to the second solid band past the
delay settings.
9(Off):To stop the wipers, move the band to off.
172

Clear ice and snow from the wiper blades before
using them. If they are frozen to the windshield,
carefully loosen or thaw them. If the blades
become worn or damaged, replace with new
blades or blade inserts.
Heavy snow or ice can overload the wiper motor.
A circuit breaker will stop the motor until it cools.
Clear away snow or ice to prevent an overload.
Your vehicle has wiper-activated headlamps.
After the windshield wipers have completed eight
wipe cycles within four minutes, the headlamps
automatically turn on. SeeWiper Activated
Headlamps on page 197for more information.Rainsense™ II Wipers
If your vehicle has this feature, the moisture
sensor is mounted on the interior side of the
windshield behind the rearview mirror. It is used
to automatically operate the wipers by monitoring
the amount of moisture build-up on the windshield.
Wipes occur as needed to clear the windshield
depending on driving conditions and the sensitivity
setting. In light rain or snow, fewer wipes will occur.
In heavy rain or snow, wipes will occur more
frequently. The Rainsense™ II wipers operate in
a delay mode as well as a continuous low or high
speed as needed. If the system is left on for long
periods of time, occasional wipes may occur
without any moisture on the windshield. This is
normal and indicates that the Rainsense™ II
system is activated.
173

The Rainsense™ II system can be activated by
turning the wiper band to one of the ve sensitivity
levels indicated on the wiper stalk. The position
closest to off is the lowest sensitivity setting, level
one. This allows more rain or snow to collect on the
windshield between wipes. Turning the wiper band
away from you to higher sensitivity levels increases
the sensitivity of the system and frequency of
wipes. The highest sensitivity setting, level ve is
closest to low. A single wipe will occur each time
you turn the wiper stalk to a higher sensitivity level
to indicate that the sensitivity level has been
increased.
Notice:Going through an automatic car wash
with the wipers on can damage them. Turn
the wipers off when going through an
automatic car wash.The mist and wash cycles operate as normal and
are not affected by the Rainsense™ II function.
The Rainsense™ II system can be overridden at
any time by manually turning the wiper band to low
or high speed.
When Rainsense™ II is active, the headlamps
will turn on automatically. The headlamps will
turn off again once the wipers turn off if it is light
enough outside. If it is dark, they will remain
on. SeeWiper Activated Headlamps on page 197
for more information.
Notice:Do not place stickers or other items
on the exterior glass surface directly in front of
the moisture sensor. Doing this could cause
the moisture sensor to malfunction.
174

Windshield Washer
{CAUTION:
In freezing weather, do not use your
washer until the windshield is warmed.
Otherwise the washer uid can form ice
on the windshield, blocking your vision.
J(Washer Fluid):Press and release
this paddle, located at the top of the turn
signal/multifunction lever, to spray washer
uid on the windshield. The wipers will clear
the windshield and either stop or return to your
preset speed. For more washer cycles, press
and hold the paddle.
_(Heated Washer Fluid):The heated
windshield washer uid system, if your vehicle
has this feature, may be used to help clear
ice, snow, tree sap, or bugs from your windshield.Sliding the switch on the turn signal/multifunction
lever to this position and then releasing it will
activate the heated windshield washer uid
system. This activation will initiate four heated
wash/wipe cycles. The rst heated wash/wipe
cycle may take up to 40 seconds to occur,
depending on outside temperature. After the rst
wash/wipe cycle, it may take up to 20 seconds
for each of the remaining cycles. The heated
windshield washer uid system may be turned off
at any time by sliding the switch on the turn
signal/multifunction lever to this position again.
When the heated windshield washer uid system
is activated under certain outside temperature
conditions, steam may ow out of the washer
nozzles for a short period of time before washer
uid is sprayed. This is a normal condition.
WASHER FLUID LOW ADD FLUID will be
displayed on the Driver Information Center (DIC)
when the washer uid is low. SeeDIC Warnings
and Messages on page 246.
175

Cruise Control
With cruise control, you can maintain a speed of
approximately 25 mph (40 km/h) or more without
keeping your foot on the accelerator. This is helpful
on long trips. Cruise control does not work at
speeds below about 25 mph (40 km/h). When
cruise control is on, you will see a cruise light
on the instrument panel cluster.
When you apply your brakes, the cruise control
shuts off.{CAUTION:
Cruise control can be dangerous where
you cannot drive safely at a steady speed.
So, do not use your cruise control on
winding roads or in heavy traffic.
Cruise control can be dangerous on
slippery roads. On such roads, fast
changes in tire traction can cause
excessive wheel slip, and you could
lose control. Do not use cruise control
on slippery roads.
If your vehicle is in cruise control when the
Traction Control System (TCS) begins to limit
wheel spin, the cruise control automatically turns
off. SeeTraction Control System (TCS) on
page 309. When road conditions let you safely use
it again, you can turn the cruise control back on.
176