2007 CADILLAC CTS V wheel

Notice:If your vehicle has 245/45R18,
P245/45ZR18 or P225/50R18 size tires, they are
classied as low-prole tires. Low-prole
tires are more susceptible to damage from road
hazards or curb impact than standard prole
tires. Tire and or wheel assembly damage
can occur when coming into contact with road
hazards like, potholes, or sharp edged
objects or when sliding into a curb. Your GM
warranty does not cover this type of damage.
Keep tires set to the correct ination
pressure and when possible avoid contact with
curbs, potholes and other road hazards.
Winter Tires
If you expect to drive on snow or ice covered
roads often, you may want to get winter tires for
your vehicle. All season tires provide good overall
performance on most surfaces but they may
not offer the traction you would like or the same
level of performance as winter tires on snow or ice
covered roads.Winter tires, in general, are designed for increased
traction on snow and ice covered roads. With
winter tires, there may be decreased dry
road traction, increased road noise, and shorter
tread life. After switching to winter tires, be alert for
changes in vehicle handling and braking.
See your dealer for details regarding winter tire
availability and proper tire selection. Also,
seeBuying New Tires on page 411.
If you choose to use winter tires:
Use tires of the same brand and tread type on
all four wheel positions.
Use only radial ply tires of the same size, load
range, and speed rating as the original
equipment tires.
Winter tires with the same speed rating as your
original equipment tires may not be available for H,
V, W, Y, and ZR speed rated tires. If you choose
winter tires with a lower speed rating, never
exceed the tire’s maximum speed capability.
393

(B) Tire Width:The three-digit number indicates
the tire section width in millimeters from sidewall
to sidewall.
(C) Aspect Ratio:A two-digit number that
indicates the tire height-to-width measurements.
For example, if the tire size aspect ratio is 60,
as shown in item C of the illustration, it would
mean that the tire’s sidewall is 60 percent as high
as it is wide.
(D) Construction Code:A letter code is used to
indicate the type of ply construction in the tire.
The letter R means radial ply construction;
the letter D means diagonal or bias ply
construction; and the letter B means belted-bias
ply construction.
(E) Rim Diameter:Diameter of the wheel in
inches.
(F) Service Description:These characters
represent the load range and speed rating of the
tire. The load index represents the load carry
capacity a tire is certied to carry. The load index
can range from 1 to 279. The speed rating is
the maximum speed a tire is certied to carry a
load. Speed ratings range from A to Z.Tire Terminology and Denitions
Air Pressure:The amount of air inside the tire
pressing outward on each square inch of the
tire. Air pressure is expressed in pounds
per square inch (psi) or kilopascal (kPa).
Accessory Weight:This means the combined
weight of optional accessories. Some examples of
optional accessories are, automatic transmission,
power steering, power brakes, power windows,
power seats, and air conditioning.
Aspect Ratio:The relationship of a tire’s height
to its width.
Belt:A rubber coated layer of cords that is
located between the plies and the tread. Cords
may be made from steel or other reinforcing
materials.
Bead:The tire bead contains steel wires wrapped
by steel cords that hold the tire onto the rim.
Bias Ply Tire:A pneumatic tire in which the plies
are laid at alternate angles less than 90 degrees
to the centerline of the tread.
397

Vehicle Capacity Weight:The number of
designated seating positions multiplied by 150 lbs
(68 kg) plus the rated cargo load. SeeLoading
Your Vehicle on page 321.
Vehicle Maximum Load on the Tire:Load on an
individual tire due to curb weight, accessory
weight, occupant weight, and cargo weight.
Vehicle Placard:A label permanently attached to
a vehicle showing the vehicle’s capacity weight
and the original equipment tire size and
recommended ination pressure. See “Tire and
Loading Information Label” underLoading
Your Vehicle on page 321.
Run-Flat Tires (CTS-V)
If your vehicle has run-at tires, there is no spare
tire and no tire changing equipment. Your
vehicle also has a Tire Pressure Monitor (TPM)
which will alert you if there is a loss of tire pressure
in any of the tires. SeeTire Pressure Monitor
System on page 405.
{CAUTION:
When the low tire warning light is
displayed on the instrument panel cluster,
your vehicle’s handling capabilities will be
reduced during severe maneuvers. If you
drive too fast, you could lose control of
your vehicle. You or others could be
injured. Do not drive over 55 mph (90 km/h)
when the low tire warning light is
displayed. Drive cautiously and check your
tire pressures as soon as you can.
If a tire goes at, you will not need to stop on the
side of the road to change the tire. You can
just keep on driving. The tire can operate
effectively with no air pressure for up to 65 miles
(105 km) at speeds up to 55 mph (90 km/h).
The shorter the distance you drive and the slower
the speed, the greater the chance that the tire
will not have to be replaced. When a tire is lled
with air, it provides a cushion between the
road and the wheel.
400

Because you will not have this cushion when
driving on a deated run-at tire, try to avoid
potholes that could damage your wheel and
require replacement of it.
Some road hazards can damage a tire beyond
repair. This damage could occur even before you
have driven on the tire in a deated condition.
When a tire has been damaged, or if you
have driven any distance on a run-at tire, check
with an authorized run-at tire service center
to determine whether the tire can be repaired or
should be replaced. To maintain your vehicle’s
run-at feature, all replacement tires must
be self-supporting tires. As soon as possible,
contact the nearest authorized GM or run-at
servicing facility for inspection and repair or
replacement. To locate the nearest GM or run-at
servicing facility, call Roadside Service. See
Roadside Service on page 488for details.
{CAUTION:
Run-at tires are constructed differently
than other tires and could explode during
improper service. You or others could be
injured or killed if you attempt to repair,
replace, dismount, or mount a run-at tire.
Let only an authorized run-at service
center repair, replace, dismount, and
mount run-at tires.
The valve stems on your run-at tires have sensors
that are part of the Tire Pressure Monitor System
(TPMS). These sensors contain batteries which are
designed to last for 10 years under normal driving
conditions. See your dealer if you ever need to
have a wheel replaced, or if the sensors ever need
replacement.
Notice:Using liquid sealants can damage the
tire valves and tire pressure monitor sensors in
your vehicle’s run-at tires. This damage would
not be covered by warranty. Do not use liquid
sealants in your vehicle’s run-at tires.
401

The high-performance tires, size P225/55R16,
P225/50R17 or P225/50R18 require ination
pressure adjustment when driving your vehicle at
speeds of 100 mph (160 km/h) or higher. Set
the cold tire ination pressure to the maximum
ination pressure shown on the tire sidewall,
or 38 psi (262 kPa), whichever is lower. See the
example following.
Example:
You will nd the maximum load and ination
pressure molded on the tire’s sidewall, in small
letters, near the rim ange. It will read something
like this: Maximum load 710 kg (1565 lbs)
350 kPa (51 psi) Max. Press.
For this example, you would set the cold ination
pressure for high-speed driving at 38 psi (262 kPa)
When you end high-speed driving, return the tires
to the cold ination pressures shown on the
tire and loading information label. SeeLoading
Your Vehicle on page 321.Tire Pressure Monitor System
Your vehicle may have a Tire Pressure Monitor
System (TPMS). This system uses radio and
sensor technology to check tire pressure levels.
If your vehicle has this feature, sensors are
mounted on each the tire and wheel assembly,
except for the spare tire. The TPMS sensors
monitor the air pressure in the vehicle’s tires and
transmits the tire pressure readings to a receiver
located in the vehicle.
If your vehicle has the base audio system, the
Driver Information Center (DIC) displays TPMS
warnings and messages on the radio’s display
screen. SeeSystem Controls on page 223
andDIC Warnings and Messages on page 232for
additional information and details about the DIC
operation and displays. If your vehicle has
the Navigation system, TPMS warnings and
messages are displayed on the message center
screen, located inside the tachometer. See
Message Center (CTS-V) on page 215for
information about the message center operation
and displays.
405

Your vehicle’s TPMS can alert you about a low
tire pressure condition but it does not replace
normal tire maintenance. SeeTire Inspection and
Rotation on page 409andTires on page 392.
Notice:Do not use a tire sealant if your vehicle
has Tire Pressure Monitors. The liquid sealant
can damage the tire pressure monitor sensors.
Resetting the TPMS Identication
Codes
Each TPMS sensor has a unique identication
code. Any time you replace one or more of
the TPMS sensors or rotate the tires, the
identication codes will need to be matched to the
new tire and wheel position. The sensors are
matched to the tire and wheel positions in
the following order: driver’s side front tire,
passenger’s side front tire, passenger’s side rear
tire, and driver’s side rear tire using a TPMS
diagnostic tool. See your GM dealer for service.
The TPMS sensors may also be matched to each
tire and wheel position by increasing or
decreasing the tire’s air pressure. When increasing
tire pressure do not exceed the maximum
ination pressure indicated on the tire’s sidewall.You will have two minutes to match the rst tire
and wheel position, and ve minutes overall
to match all four tire and wheel positions. If it takes
longer than two minutes, to match the rst tire
and wheel, or more than ve minutes to match all
four tire and wheel positions the matching
process stops and you will need to start over.
The TPM matching process is outlined below:
1. Set the parking brake.
2. Turn the ignition switch to ON with the
engine off.
3. Using the Remote Keyless Entry (RKE)
transmitter, lock and unlock the vehicle’s
doors.
4. Press the lock and unlock buttons, at the
same time, on the RKE transmitter. A single
horn chirp will sound, indicating that the
TPMS system is ready, and the sensor
matching process can begin.
5. Start with the driver’s side front tire.
407

6. Remove the valve cap from the valve stem.
Activate the TPMS sensor by increasing
or decreasing the tire’s air pressure for
ve seconds, or until a horn chirp sounds. The
horn chirp, which may take up to 30 seconds,
conrms that the sensor identication code has
been matched to this tire position. To decrease
the tire’s air-pressure use the pointed end of
the valve cap, a pencil-style air pressure gage,
or a key.
7. Proceed to the passenger’s side front tire, and
repeat the procedure in Step 6.
8. Proceed to the passenger’s side rear tire, and
repeat the procedure in Step 6.
9. Proceed to the driver’s side rear tire, and
repeat the procedure in Step 6.
10. After hearing the conrming double horn
chirp, for the left rear tire, exit the matching
process by turning the ignition switch to OFF.
11. Set all four tires to the recommended
air pressure level as indicated on the tire and
loading information label.
12. Put the valve caps back on the valve stems.The TPMS will not function properly, if one or
more of the TPMS sensors are missing or
inoperable. If your vehicle has a compact spare
tire, the spare tire and wheel assembly does
not contain a TPMS sensor. If you replace one of
the road tires with the spare, or if the system
detects a missing or inoperable sensor, the
Service Tire Monitor System message will be
displayed on the DIC. If you have replaced a tire
and wheel assembly without transferring the
TPMS sensors, the error message will be
displayed. Once you re-install the TPMS sensors,
the message should go off. See your GM
dealer for service if all TPMS sensors are installed
and the error message comes on and stays on.
Have your vehicle serviced as soon as possible.
If your vehicle has a message center and the
system detects a missing or inoperable sensor an
error message of several dashes–––will be
shown on the message center display. If you have
replaced a tire and wheel assembly without
transferring the TPMS sensors, the error message
will be displayed. Once you re-install the TPMS
sensors, the error message should go off.
See your GM dealer for service if all TPMS
sensors are installed and the error message
comes on and stays on.
408

Federal Communications Commission
(FCC) and Industry and Science Canada
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following
two conditions:
1. This device may not cause harmful
interference.
2. This device must accept any interference
received, including interference that may
cause undesired operation.
This device complies with RSS-210 of Industry
Canada. Operation is subject to the following
two conditions:
1. This device may not cause interference.
2. This device must accept any interference
received, including interference that may
cause undesired operation of the device.
Changes or modications to this system by other
than an authorized service facility could void
authorization to use this equipment.
Tire Inspection and Rotation
Tires should be rotated every 5,000 to 8,000 miles
(8 000 to 13 000 km).
If your vehicle has P245/45ZR18 96W size tires,
GM recommends rotating these tires at 3,000 mile
(4 800 km) intervals. These tires are optimized for
dry traction and handling performance. Tread life
may be 15,000 miles (24 140 km) or less for these
tires, depending on how and where you drive.
Any time you notice unusual wear, rotate your
vehicle’s tires as soon as possible and check
wheel alignment. Also check for damaged tires or
wheels. SeeWhen It Is Time for New Tires on
page 411andWheel Replacement on page 416for
more information.
The purpose of regular rotation is to achieve more
uniform wear for all tires on the vehicle. The
rst rotation is the most important. SeeScheduled
Maintenance on page 462.
409